Military Engineer Services - Bihar

37044332 tender for special repair to omqs / smqs at af station bihta 1 excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 m deep and getting out including forming bottom surface for laying of pipes complete all as specified and directed. 2 returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 mm thick complete all as specified and directed. 3 removal of excavated material to a distance not exc 50 meter and depositing wheredirected at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 4 supplying, laying and cushioning for cable protection in trenches 8 cm deep before laying cable and 15 cm deep over the cable including well punning complete all as specified and dierected 5 m&l cement concrete 1:5:10 type e2, using 40 mm graded stone coarse aggregate in sunken floor, all as specified and directed 6 m&lreinforced cement concrete (1:2:4) type b 1, (20 mm graded aggregate) as in slab supported on walls, beam, column and in similar work, complete all as specified and directed. 7 s & f for factory made solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet, reinforced with ms square tube fixed in opening complete as per manufacturers specifications and as directed. 8 s & f for 30 mm thick factory made solid panel pvc door shutter conferming to criteria of testing as per is : 4020, consisting of frame made out of ms tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails ms frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded pvc `c channel of size 30x50mm forming styles and 5mm thick 75mm wide pvc sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross pvc sheet as gap insert for top rail and bottom rail panelling of 5 mm thick pvc sheet to be fitted in the ms frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick pvc sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick pvc strip of 20 mm width is to be struck on the interior side of c channel using pvc solvent adhesive complete as per manufacturers specifications & drawings & all as directed. 9 s & f pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete as specified. 10 s & f pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified. 11 m & l for pcc 1:3:6 type c 0 using 12.5mm aggregate crushed stone aggregate as in filling back side of pressed steel door/window frames, all as specified & directed. 12 s&f glazed/wire gauged/skeleton shutter 35 mm thick out of (well kilnseasoned)2nd class hard wood (hollock) the size of rails and style as per is chemically pressure treated in factory gainst termite infestation prepared to receive wire gauge (without sash bars) edges of frame chamfered or rounded fitted with cut and mitered beads, all as specified & directed.(note : wire gauge/glazing to be measured and paid separately). 13 s&f factory made 40 mm thick plain, framed, panelled shutter (two panel) with lock rail using 2nd class hw (hollock) kiln seasoned andchemicallypressure treated the size of rail and style as per is 1003 (part i) and panel insert of 9mm thick bwp commercial facing plywood or 12mm veneered particle boards with commercial ply all as specified 14 s&f plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed in 2nd class hardwood. 15 s&f of 25 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both sides all as specified and as directed. 16 s&f in repairs of 12 mm thick plywood, grade bwr, type bb, fixed with screws to timber frame work etc. in built in cupboard complete all as specified and as directed. 17 s&f for 100mm long mild steel butt hinges, heavy weight cold rolled mild steel, all as specified and as directed. 18 s&f for 75mm long mild steel butt hinges, heavy weight cold rolled mild steel, all as specified and as directed. 19 s&f 150 mm long aluminium anodised handles, cast type, all as specified and as directed. 20 s&f for 150 mm long aluminium, anodised, barrel tower bolts of extruded section, all as specified and as directed. 21 s&f 300 mm long aluminium alloy, anodised, sliding dooor bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, all as specified and as directed. 22 s&f for 200 mm long aluminium, anodised, barrel tower bolts of extruded section, all as specified and as directed. 23 s&f mild steel 300 mm ordinary rat tail rod pattern springs including roller & rooler plate complete all as specified and as directed. 24 s&f floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140mm, all as specified and as directed. 25 s&f hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws of 100 mm size, all as specified and as directed. 26 s&f in repairs of harrison rail mild steel chromium plated of 19/20mm dia for curtain rod fixed with two nos of brackets for each rail all as specified and as directed. 27 s&f mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, all as specified and as directed. 28 s&f anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed. (note : minimum thickness of powder coating 50 micron). 29 s&f anodised aluminium powder coated window and ventilator shutters, hung type without sash bar, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. anodised aluminium fittings such as peg stays 150 mm long (01 no), hinges b 21 100 mm long (02 no), suitable handle (01 no) complete all as specified.(note : minimum thickness of powder coating 50 micron). 30 s&f sheet glass 4 mm thick ordinary quality & glazing with rubber gasket in square n.exc 0.5 sqm in each pane, all as specified and directed.. 31 s&f 3 mm thick figured glass, pinhead type in squares n.exc 0.50 sqm each pane, all as specified and directed. 32 m&lfor mild steel tmt bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete, all specified and directed. 33 s&f in repair 18mm thick celuka pvc sheet minimum 600 kg/cum density grade 1 quality of both side plain white colour rigidlam glossy finish fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet sides top and bottom and shelves inside the cabinet completeas per specifications and as directed. note: (i) cup board accessories ie fittings,handles,hinges, will be measured and paid under this schedule.(ii) quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type).(iii) fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only. 34 s&f auto closing stainless steel (grade 304) hinges 35 mm of 0 crank (kh 001) or 8 crank (kh 002) openable at 110 degree for kitchen cabinet shutters all as specified & directed. 35 s&f stainless steel handles of 100 mm size for kitchen cabinet shutter complete all as specified. 36 m&l for app basedpolymeric water proofing membrane minimum weight 3 kg/ sqm and minimum 3mm thick reinforced with polyster non wove fabrick (weight not less than 150gms/sqm), laid with torched application with the strict supervision of manufacturers technical supervisor, laid over hot blown bitumen 85/25 grade @1.2 kg per sqm over bitumen primer @0.30 ltr/sqm including cleaning surface, complete all as specified and directed.(note membrane shall be laid with 100mm side/end lap on prepared surface as per manufacturer instruction work shall be carried out strictly with the technical tradesmen and supervision of technical staff of manufacturer) 37 m&l for 40 mm thick brick tiles laid on bedding of 15 mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) on treated roof all as specified and as directed 38 m&l for applying bituminous primer @ 0.40 kg/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm as in sunken complete all as specified including fixing of 40 mm dia gi spout pipe at bottom of slab/plastered surface etc, all as specified & directed. 39 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, all as specified & directed. 40 m&l for providing cement concrete type b 1, 1:2:4 (20 mm graded aggregate) as in roof padding, roof kerbs (rounded or chamfered on edge) etc all as specified & directed. 41 m&l 75 mm thick cement concrete type d 2, 1:4:8 (using 40 mm graded aggregate) as in subbase to floor, ll as specified and directed.. 42 m&l for 25 mm thick cement concrete type b 0, 1:2:4 (12.5 mm graded aggregate) as on floor, ll as specified and directed.. 43 m & lnon skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15 mm thick screed bed in cement mortar 1:6 all as specified and directed. 44 m & lnon skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15 mm thick screed bed 1:6 all as specified and directed. 45 m & l glazed ceramic coloured tiles of approved quality isi marked (450 x 300 x 7 mm / 350 x 250 x 7 mmthick) as in vertical surfaces such as skirting dados etc set jointed in neat cement slurry and pointed in coloured cement to match with the tiles including 1:4 cement plaster 10 mm thick on brick work and concrete surface, all as specified and directed. 46 m&l for 15 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms (including a hole of gas pipe) and like including 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, all as specified and directed. 47 rounding to edges of stone slabs one edge, such as in steps, cooking platform, and similar situations, all as specified and directed.. 48 m&l for rendering 10 mm thick in cement mortor 1:4 on fair faces of brick work, surfaces finished even and fair without using extra cementwith water proofing compound, all as specified and directed. (note : wpc shall be measured and paid seperatelly). 49 m&l for 10 mm thick rendering in cement mortor (1:6) on air faces of brick work, surfaces finished even and smooth without using extra cement cement, all as specified and directed 50 m & l for 15 mm thick rendering in cm (1:4) on vertical surfaces of brick walls finished even and smooth without using extra cement with using water proofing compound, all as specified & directed. (note wpc will be measured and paid separately). 51 m&l for 5 mm thick rendering in cm (1:3) on ceiling surfacesoffinished even and fair without using extra cement, all as specified & directed.. 52 supply only integral water proofing compound 53 s&f 15 mm gi tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors including taking up or down old steel tube complete all as specified and directed. 54 s&f 20 mm gi tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors including taking up or down old steel tube complete all as specified and directed. 55 m&l for preparation of new wood basesurfaces of any description, over 10 cm in width or girth, not otherwise described and appling twocoats of synthetic enamel paint (ordinary tint) overone coats of pink primer, all as specified and directed. 56 m&l peparation of old painted wooden surfaes of any dscription over 10cm width or girth and applying one coatof synthetic enamel paint complete all as specified and as directed. 57 m&l peparation of old painted steel surfaces of any description over 10cmwidth or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. 58 m&l for preparation of new plastered surfaces of ceiling and applying three coats of white wash all as specified and directed. 59 m&l for preparation of old surfaces of ceiling and applying two coats of white washall as specified and directed. 60 m&l for preparation of new plastered surfaces of wall and applying three coats of white wash all as specified and directed. 61 m&l for preparation of old decorated plasteredsurfaces of wall and applying two coat of white wash all as specified and directed. 62 m&l for preparation of new plastered surfaces of wall and applying two coats oil bound distemper over a coat of alkali resistant primer over a coat of 1 mm thick wall care putty in two different layers complete all as specified & as directed.(note treatment slall be carried our by spraying with mechanical means) 63 m&l for complete removal of existing treatment of wall and applying two coats oil bound distemper over a coat of alkali resistant primer over a coat of 1 mm thick wall care putty in two different layers complete all as specified & as directed.(note treatment slall be carried our by spraying with mechanical means) 64 m&l for complete removing of existing treatment of wall surfaces by scrapping with mechanical sander (having mechanical vacuum mechanism)to make surface clean, free from dust, loose paint etc and applying two coat of cement base paint of different colours complete all as specified and directed. 65 m&l for preparation of new plastered surfaces of walls and applying two coat of cement base paint of any colours and pattern (two or more colours) complete all as specified and directed.(note : colour and pattern of paint will be directed by ge) 66 m&l for pvc (swr) pipe of 110 mm boresingle socketed in any length with rubber ring joint fixed to wall with suitable clamps of adequate numbers etc complete all as specified and directed. 67 s&fpvc swr bends 110 mm boreall as specified and directed. 68 s&f cast iron soil, waste pipe100 mm dia, sand cast, in any length with or without ear, with cement joint, laid in trenches, complete all as specified. 69 s&f cast iron soil, wastepipe100 mm dia, sand cast, in any length with or without ear, with cement joint, laid in trenches, complete all as specified. 70 s&f cast iron soil, waste and vent pipe100 mm dia, sand cast, in any length with or without ear, with cement joint, fixed on wall, complete all as specified. 71 s&f cast iron soil, waste and vent pipe100 mm dia, sand cast, in any length with or without ear, with cement joint, fixed on wall, complete all as specified & directed. 72 s & f in repairs of 100 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured), all as specified & directed.. 73 s & f in repairs of 75 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured), all as specified & directed.. 74 s&f cast iron cowls of 100 mm bore pipe, all as specified & directed. 75 s & f in repairs cast iron floor trap with chromium plated graating of 100 mm size including jointing to waste pipe with cement joints etc, all as specified & directed. 76 s&f soap dish brass chromium plated decorative type, size 160x90mm complete all as specifed and directed. 77 s&f 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick ac buildg board or commercial plywood and fixed to wooden plugs with cpbrass screws and cup washers complete all as specified and directed. 78 s&f in repairbrass chromium plated, tubular towel rails 20 mm dia, d type, 60cm long between flanges, completed all as specified and directed. 79 s&f in repair chromium plated 125 mm size shower rose with swivel joints, in square with cp long shank arm including fixing to steel pipe or union of 15 mm bore, complete all as specified and as directed. 80 s&f in repairs vitreous china squatting pan “orissa pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in ssr and including s&f trap set complete all as specified and directed. 81 s&f in repairs pvc flushing cistern 10 ltr capacity valve less syphonic action type low level with and including dual flushball valve float & handle, waste pipe & brackets complete set complete all as specified and directed. 82 s & f in repairvitreous china wash basin, flat back, size 630x450mm white, excluding waste coupling, chain & plug, ci prackets, pvc waste pipe 32 mm,and porcelain stopper but including brackets. 83 s&f in repair chromium plated fancy type, stop cock/angular cock, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed. 84 s&f in repair chromium plated concealed type, stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed. 85 s & f in repair 15mm bore chromium plated bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron or brass ferrule, complete all as specified and directed. 86 s&f sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12mm wide with chromium plated bracket guard and railing, 600mm long,complete all as specified and directed. 87 s & f in repair pillar taps fancy type(long body)cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe, complete all as specified and directed. 88 s&f in repairpvc connections 15mm size with ptmt nuts of length 450 mm, complete all as specified and as directed. 89 s&frotational moulded polythene water storage tank of capacity 500 ltrs (cylindrical/vertical with closed top), triple layer construction, isi marked, hoisted & fixed in position including followings : (i)20 mm gi pipe medium grade,over flow 450mm long.(ii) 20 mm gi pipe medium grade waste pipe 600mm long.(iii) 20 mm brass ball valve/float valves, high pressure & high density plastic ball screwed for iron pipe and fixed.(iv) 20 mm gun metal globe/gate valve with iron wheel head, screwed on both ends for fixing including one gi nipple(20mm bore). 90 s&f in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including pvcwaste pipe, cp waste coupling,bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified anddirected. 91 s&f 1mm thick stainless steel kitchen plate rack of size 750x 900mm best quality assembled with brass washer and nut and bolts including hooks (spoon/cup holders) complete all as specified & directed. 92 demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level), all as specified & directed..note : all demolished items/ debris to be removed out side of mod land. 93 demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, all as specified & directed..note : all demolished items/ debris to be removed out side of mod land. 94 demolition of reinforced cement concrete of any description & in any position, complete all as specified and directed. 95 dismantling of stone slabs and tiles of any description or thickness in floors aprons etc including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 96 dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises,all as specified and directed. 97 taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed 98 taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site all as specified and directed. 99 taking down chowkats or frame with shutter (without taking out shutter from the frame) exceeding 1.50 sqm and n exc 4.00 sqm each and removal from site all as specified and directed 100 taking down of shutters of any description exc 1.00 sqm but n. exc 2 sqm each, all as specified and directed 101 taiking up or down steel tubing and connections, 15 mm bore including cleaning, complete all as specified and directed. 102 taiking up or down steel tubing and connections, 20 mm bore including cleaning, complete all as specified and directed. 103 dismantling pvc water tankcapacity exceeding 250 but not exceeding 500 ltr, complete all as specified and directed. 104 taking down100/75 mm cast iron soil waste pipe (any size or patterns) moulding all fittings heads shoes, bends etc (measured over all as fixed along the confrece line over fittings and accessories), all as specified and directed. 105 taking down rain water pipes (any size or pattern) ,including all fittings all as specified and directted . 106 demolition of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc (each layer) laid, bedded and pointed in any mortar including removal of debris/muds etc complete all as specified and as directed.note : all demolished items/ debris to be removed out side of mod land. 107 demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and finally cleaning the surface with wire brush to remove old treatment to lay pcc padding, complete all as specified and directed..note : all demolished items/ debris to be removed out side of mod land 108 taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc, complete all as specified and directed. 109 taking down old unserviceable mcb db tpn4 way (vertical), double door, 415 v, ac, 50 hz, includingmcb63 amps 16 ka ,ip 40 protection conforming to is 13032 universal mounting with copper bus bar,neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides, complete all as specified & directed. 110 material and labour for concealed point wring for one light/fan/exhaust fan point controlled by 1 no,one way 5/6 amp switch ,using approved colour coding (phase red,neutral black,earth green) complete with frls pvc insulated and unshealthedstranded copper conductor cable 1.5 sqmm single coreconforming to is 694 including medium duty concealed unplasticised pvc conduit conforming to is 9537(part 3) and isi marked not less than 20 mm dia with concealed in wall pressed steel terminal box of not less than 2 mm thick of required size including painting terminal boxs inside and outside with two coat of synthetic enamle paint over one coat of red oxide primerwith top cover3 mm thickbakelight laminated sheetwith brass screws and cup washer with all assessories including frls pvc insulated and unshealthedstranded copper conductor cable 1.5 sqmm single core in green colouras earth wireconnected to earth dolly . complete all as specified and directed . 111 all as per item no 110 above butfor one 3 pin /5 pin socket outlet 5 amp controlled by 1 no one way 5/6 amp switch on same board along with other switches ,fan regulator etc. 112 all as per item no 110 above butfor one 3 pin /5 pin socket outlet 5 amp controlled by 1 no one way 5/6 amp switch on independent board. 113 all as per item no 110 above butfor one call bell/buzzer point controlled by one push button switch. 114 material and labour for point wring ,using approved colour coding (phase red,neutral black,earth green) complete for one socket outlet 15 amp on independent board with frls pvc insulated and unshealthedstranded copper conductor cable 2.5 sqmm single coreconforming to is 694 including medium duty concealed unplasticised pvc conduit conforming to is 9537(part 3) and isi marked not less than 20 mm dia with concealed in wall pressed steel terminal box of not less than 2 mm thick of required size including painting terminal boxs inside and outside with two coat of synthetic enamle paint over one coat of red oxide primerwith top cover3 mm thickbakelight laminated sheetwith brass screws and cup washer with all assessories including frls pvc insulated and unshealthedstranded copper conductor cable 2.5 sqmm single core in green colouras earth wireconnected to earth dolly complete all as specified and directed. 115 s&f switch piano flush button single pole one way 5/6 amp, 240 volts conforming to is 3854 isi marked all as specified and directed. 116 s&ffor socket outlet, 5 pin, 5/6 amp flush type conforming to is 1293 isi marked all as specified and directed. 117 s&f switch piano flush button single pole one way 15 amp, 240 volts conforming to is 3854 isi marked including taking down old one, all as specified and directed. 118 s&ffor socket outlet, 3 pin, 15 amp flush type conforming to is 1293 isi marked including taking down old one, all as specified and directed. 119 s&fceiling rose, surface bakelite,isolated bodythree terminals including taking down old one, all as specified and directed. 120 s&f lamp holder pvc/polycarbonate type with back plate suitable for batten fittings, all as specified and directed. 121 supply only led bulb of 09 watt complete all as specified and directed. 122 s&f forbell push flush type 5 a sp 240 v all as specified and directed. 123 s&fbell (ding dong) 230 volts, single pole all as specified and directed. 124 taking down ceiling fan including cable, dismantling blades and carry out mnr repair and fixing of damaged parts like capacitor, bushes, bearings and screws etc and keeping in safe custody of contractor up to re fixing in the same. all as specified & directed. 125 m&l for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust, all as specified and directed. 126 hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, all as specified and directed. 127 m & l for repair / rewinding of ceiling fand replacement of requisite spares like bush, bearing, down rod, capacitor, fan clamp, fan blade etc if necessary all as specified and directed. 128 m & l for repair / rewinding of exaust fand replacement of requisite spares like bush, bearing, capacitor, fan clamp, fan blade etc if necessary all as specified and directed. 129 supply and fixing led tube lights fitting 1x 18w, 220v, including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling roseand complete all as specified and directed. 130 supply and fixing led batten type tube light complete fitting 1x 10 w, 220v,connecting up with three core flexible copper conductor cable of suitable size from ceiling roseand complete all as specified and directed. 131 supply &fixing and connecting up complete mcb db tpn 4 way (vertical), double door, 415 v, ac, 50 hz, with and includingmcb63 amps 16 ka ,ip 40 protection conforming to is 13032 universal mounting with copper bus bar,neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides, complete all as specified & directed. 132 s&f sheet metal enclosures (mcb distribution board) when mcb’s to be used singlepole and neutral 8 ways 220 volt with 200 amps rated bus bar, double door with bus bar neutral link earth bar, din rail, necessary blanking plated, including fixing db flush in wall complete with making good disturbed surfaces and colour matching all as specified and directed including taking down old one, complete all as specified & directed. 133 s&f mcb’s single pole, 10 ka ,32 amp to 40 amp 240 volts,and of b series with required wiring connections and lugs etc and erecting in provided enclouser/destribution board.mcbs shall be of current limiting type ,isi marked conforming to is 8828 1996, including taking down old one, complete all as specified & directed. 134 s&f sheet metalenclosure with socket plug top and mcbs single pole with a two pin and earth plug andsocket complete with one single pole mcb ofc series of cap 20 amps including taking out the old one all as specified and directed. 135 s&f mcb’s dp, 10 ka, 32 amp to 40 amp 240 volts,and of b series with required wiring connections and lugs etc and erecting in provided enclouser/destribution board. mcbs shall be of current limiting type ,isi marked conforming to is 8828 1996,including taking down old one complete all as directed. 136 supply and fixing stud 10 w led lights energy saving bulk head luminaries including led light driver, holder connecting up with three core flexible copper conductor cable of suitable size from ceiling roseand complete all as specified and directed. 137 s&f sub main wiring using approved colour coding (phase red,neutral black,earth green) complete with two single core frls pvc insulated and unsheathedstranded copper conductor cable 6 sqmmas current carrying conductor and one run of 6.0 sqmm as neutral cable ,voltage rating 1100 volt ,isi marked drawn in and including concealed pvc conduit isi marked of dia not less than 25 mm and thickness 2 mm with stranded accessories along with one run of frls pvc green colour insulated,unshealthed,stranded copper conductor of size 6 sqmm all as specified and directedincluding taking down old one, complete all as specified and directed.(note: two run of single core frls pvc cable with one run of earth contunity conductor and conduit shall be measured as one unit.) 138 m&l for earthing complete with galvanized steel earth plate 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire of 4mm dia as earthing lead by means of bolts, nuts, check nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, gi pipe light grade 15 mm bore for protection of giwire from earth electrodeto test point /machinery / equipment.supplying and laying charcoal dustcomman saltpcc(1:2:4) type b1 using 20 mm gradedstone agregratechamber andrcc cover 54 cm x 54cm x50 mm thick (1:2:4) type b 1using 20 mm stone agrigrtae )reinforced with 8 mm dia tmt bars @75mm c/c both ways with mild steel handle 12 mm dia,using round bar ,pgi funnel with wire mesh, 20 mm dia gi pipe medium grade for watering all as shown in electrical plate no 3 of ssr part 1including testing and taking out the old one complete all as specified and directed(note cost of gi wire and gi protection pipe up to a distance 7.5 m shall be includedin quated rate of above items) 139 s&f 415 v, 10 ka ,b curve miniature circuit breaker mcb tpn 63 amps, 16 ka complete all as specified and directed. 140 supply, laying, connecting and testing xlpe cable underground pvc insulated and over all sheathed with aluminium conductor heavy duty 1100 volts grade 3.5 core 35 sqmm sizes, laid in trenches, floors, ducts passing through pipe forroad crossing etc including taking down old unsv cable of any size complete all as directed including taking out old damaged cable and all as specified and directed. (note excavation, earth work, brick protection sand cushioningand gi pipe etc shall be measured & paid for separately) 141 m&l for laying of bricks subclass ‘b’ old size having crushing strengh not s than 75 kg/sqcm, laid flat perpendicular to the direction of cable for protection of cable complete all as specified & directed. 142 m&l gi tubing 50 mm dia light grade, laid in trench/floor or fixed on wall with all fixingaccessories etc as specified and directed. ...

Department of Defence Production - Bihar

35997455 bids are invited for micro mech pump and spares mse bare pump model no mic 32 to 160 , mechanical seal set , base frame ms , impeller solid pfa lined , back plate with pfa lined , casing with pfa lined , coupling set ms total quantity : 10...

Indian Oil Corporation Limited - Bihar

34557484 supply of fs elliot compressor spares at barauni refinery , list of item(s) / work(s) as per tender documents , rotor a1 l.s, p/n 250990 312 , rotor a1 h.s, p/n 250097 546 , brg, jour. p300,p400,a,a1, p/n dp1087 6 , shim pack,p/n:280002 gr1 , brg,thrust(inactive),p/n:p1562g9300 , brg,thrust(active),p/n:p1562g9350 , shim (brass),p/n:p835b3000 , seal oil,p/n:p7963a1450 , retaining ring, p/n p27j61 , o ring , seal housing,p/n:p700d040 , ring, retaining, p/n 280004 3 , seal carbon ring,p/n:p7963a3110 , o ring , back plate,p/n:p700d238 , o ring, p/n p700a010 , shim diffuser, p/n 270689 gr 1 , shim casing, p/n p835w152 , filter elt,primary air,p/n:p3515f200 1 , filter elt,secondary air,p/n:p3515f200 2 , filter elt,oil mist,p/n:p3515b165 1 , oil filter elt,p/n:p99v15 , main oil pump,p/n:p7210t1050 , oil cooler, p/n p2275j1080...

Department Of Science And Technology - Bihar

33967262 bids are invited for mech lab equipments ( q3 ) , milling machine is:6893 , is:8614 , is:9474 ( q2 ) total quantity : 2 1 engineering mechanics lab. equipment a screw jack apparatus with weights screw jack ( without weights)all metallic construction accurately machine cut screw with a pitch of 5 mm carrying a double fanged turn table of about 20 cm diameter. fitted on a heavy cast iron base and complete with two adjustable pulleys, cord and hooks. 02 b worm and worm wheel :: single with weights an all metallic self contained apparatus useful for demonstrating the efficiency for worm and wheel and also the principle of work. consisting of a machine cut worm gear of 25 cm diameter, carrying a meta l drum of 12 cm diameter, and machine cut worm on steel spindle carrying a 12 cm diameter pulley. 02 c worm and worm wheel :: double with weights an all metallic self contained apparatus useful for demonstrating the efficiency of worm and wheel and also the principle of works. consisting of machine cut worm gear of 25 cm diameter, carrying a metal drum on 12 cm diameter, and machine cut worm on steel spindle carrying a 12 cm diameter pulley. double weight 02 d worm and worm wheel :: tripple with weights an all metallic self contained apparatus useful for demonstrating the efficiency of worm and wheel and also the principle of work, consisting of machine cut worm gear of 25cm diameter carrying a metal drum of 12 cm diameter pulley. 02 e wheel and differential axle 30 cm with weight the axle having dia of 15 & 7.5 cm respectively giving a ratio of 1:2:4. centre of the wheel which is mounted on ball bearing in cast iron brackets reducing friction to minimum. 02 f winch crab single purchase with weight fitted with heavy cast iron wall brackets. the grooved wheel is of 25 cm diameter and gears are machine cut. this apparatus is used for experiments in efficiency of mechanical advantage weights are included. 02 g winch crab double purchase with weight there are two geared wheels; one wheel carries a big axle round which a string is wound to lift a load w. the second geared wheel (upper one) carries a pulley which a string is wound to carry the effort p. suppose the first geared wheel (with axle) has n1 teeth and the second geared wheel (with pulley) is given n revolutions the first geared wheel will take : n(n1/n2 ) 02 h universal force table (normal) for experimentally verifying the lows of triangle, parallelogram and polygon if force comprising of equal circular 40cm.dia.aluminiym disc graduated into div ,compel with levelling screws, clamping device to fix the table ,string and five sets iron nicked slotted weight. 02 i moment of inertia of flywheel 25 cm with weights. experiment on the moment of mass inertia of a flywheel. steel flywheel. steel shaft used as drive pulley. set of weights ball bearing mounted shaft. anodised aluminium base plate wall mounted. 25 cm with weights 02 j parallel forces apparatus (dial type 10 kg. balance) verification of condition of equilibrium of parallel forces, law of lever and forces on beam etc. consisting of two compression thrust type 10 kg. dial type compression balances fixed on wooden polished board, a wooden bar with steel back plate 02 2 machine drawing lab. equipment a hemispherical sectional models of screw threads whitworth, square, butteress, acme. right and left hand screw; set of all the six threads made of aluminium metal mounted on base with nomeclature 02 b hemispherical sectional models of screw threads nuts set of six sectional model of nuts, properly mounted on base with nomenclature. 02 c standard bolt diameter 25 mm, length about 15 cm. approximately. properly constructed model is of aluminium alloy, complete with whit worth nut, lock nut and washer. 02 d bolts of four types ordinary. eye type, stud type and set screw type. properly constructed and mounted on base with nomenclature. 02 e foundation bolts 02 rag bolt, cotter bolt and lewis bolt a set of three aluminium models fitted on base. f foundation bolts (with nomenclature) four different types of bolts with nomenclature mounted on base. 02 g locking arrangement of bolts check nut, castle nut. grooved nut, swan nut, stop plate nut and spring washer nut. with the help of these models actual locking systems can be demonstrated. 02 h rivetted joints wooden 02 i screw jack apparatus with weights all metallic construction accurately machine cut screw with a pitch of 5 mm carrying a double fangedturntableofabout20cmdiameter.fittedon a heavy cast iron base and complete with two adjustable pulleys, cord and hooks. with weight 02 j bush bearing 02 k plummer block or pedestal bearing 02 l foot step bearing 02 m flexible coupling 02 n flanged coupling 02 o stuffing box 02 p connecting rod 02 q spark plug 02 3 fluid machinery a reciprocating pump test rig description: the experimental unit provides the basic experiments to get to know the operating behaviour and the important characteristic variables of piston pumps. setup features a closed water circuit with water tank, a piston pump with variable speed via a frequency converter and an air vessel. the piston of the pump is mounted in a housing and can be observed during operation. the cycle that takes place (intake and discharge of water) can be shown clearly in the p v diagram. the pulsating pressure curve of the pump can be damped with the aid of the air vessel. flow rate and head are adjusted via a needle valve and overflow valve. the experimental unit is fitted with manometer for pressure and sensor for flow rate. pressure manometer measures the pressure at the outlet of the pump. specification: · functioning and operating behaviour of a piston pump · closed water circuit contains piston pump with variable speed via frequency converter, transparent water tank and air vessel ·valve for adjusting the flow rate · overflow valve for adjusting the head · pulsation damping of the head using air vessel with bleed valve ·manometer for pressure at pump outlet. technical details: piston pump speed: 30…180min 1 max. flow rate: 135l/h max. head: 40m drive motor power: 180w gear transmission ratio: i=7,5 overflow valve: 1…4bar measuring ranges pressure (outlet): 0…5bar flow rate: 0,2…6l/min experimentation: principle of operation of a piston pump recording of pump characteristics pressure curves of delivery pressure p v diagram determination of efficiencies 01 b centrifugal pump test rig ms tank with frp lining unit, centrifugal pump of size 25x25mm todischarge about 60 lpm at 12m total head when run at maximum 01 speed.motor1hpdcelectricmotorisimarkedspeedvariationthirstiercontrolled arrangement with panel board. electrical panel: dp switch, isimark & energy meter for the measurement of input power. sump tank:size : 800 x 800 x 500 mm , measuring tank : size 400x400x600mmprovided with standard fittings for measuring discharge of water. digitalstop watch, others: piping system consisting of pipes, gate valve (isimark) & fittings with pressure gauge,a standard pump of 1 hp, allaccessories and spares for normal running maintenance of the machine (1set), 2 hard copies of operation manual willbe supplied along with theset up c hydraulic bench the hydraulic bench should be suitable for the use of basic fluid mechanics experiments of fluid mechanics. it should supply the water in the closed circuit; the determination of volumetric flow rate and the positioning of the experimental unit on the working surface of the base module and the collection of dripping water. the closed water circuit consists of the sump tank with the submersible pump and the measuring tank arranged above, in which the returning water is collected. the measuring tank is stepped, for large and smaller volumetric flow rates. a measuring cylinder should be provided for very small volumetric flow rates. a stopwatch should also be provided for measuring the flow rate. the top surface should enable the various experimental units to be easily and safely positioned. specification 1. base module for supplying experimental units in fluid mechanics 2. closed water circuit with storage tank, submersible pump and measuring tank. 3. measuring tank divided into two for volumetric flow rate measurement. 4. measuring cylinder with scale for very small volumetric flow rates.. 5. measurement of volumetric flow rate by using a stopwatch. 6. work surface with inside edge for safe placement of the accessories and for collecting the dripping water. technical data pump power consumption:500 750 w max. flow rate:200 450l/min max. head: 7 14m storage tank, contents: 180l measuring tank at large volumetric flow rates: 40l at small volumetric flow rates: 10l measuring cylinder with scale for very small volumetric flow rates content: 2l utility required 230v, 50/60hz,1 phase 01 d air blower apparatus description: this equipment comprises of a fd centrifugal blower coupled to a motor. three interchangeable impellers with forward, backward and radial vanes are provided with the test rig. a pitot tube is provided in the delivery line of blower for static and dynamic pressure measurement. power input to the dc motor is varied by means of a thyristor controlled dc drive to vary the rpm of motor. a rpm indicator with proximity sensor indicates the rpm of blower. technical details: motor: dc motor with thyristor controlled dc drive for variable speed blower: centrifugal, forced draft type impeller (3 nos.): forward curved, backward curved & radial curved pitot tube (with manometer): for static, dynamic & differential pressure measurement. stop watch: electronic control panel comprises of : standard make on/off switch, mains indicator, etc. energy measurement: electronic energy meter. rpm measurement: digital rpm indicator with proximity sensor. instruction manual: an english instruction manual will be provided along with the apparatus. experimentation: · to study the effect of forward curved, back curved and radial curved impeller. 01 · to find out the discharge, head and efficiency of the centrifugal blower. · to plot the graph efficiency vs discharge · to plot the graph discharge vs head 4 dynamics of machinery a four bar chain mechanism 01 b slide crank mechanism set of 3 01 c slip & creep measurement apparatus the apparatus consists of a variable speed d.c. motor, driving pulley and driven pulley of equal diameter. the pulleys ore mounted on input shaft (motor shaft) and output shaft. the driven pulleys can slide on the base with bearing block to change initial tension in belt. brake drum mounted on output shaft helps to measure power output. the motor speed is varied by dimmer stat. a two channel rpm indicator is provided to measure speeds of driven and driving pullies respectively. specifications: d.c. motor:1 hp 1500 rpm, variable speed. driving & driven pullies of equal diameters. brake drum along with spring balance. flat belt of fixed length of following materials: fabric belt , rubber belt tightening arrangement, speed controller unit, two channel digital apm indicator stroboscope. range of experiment: to measure co efficient of friction between pulley material and different belt materials. to measure power transmitted with varied belt tensions and plotting graph of (t1 t2). tension characteristics. to measure percentage slip at fixed belt tension by varying load on brake drum and plot graph of (t1 t2) vs percentage slip le. slip characteristics. finding a creep zone from graph. to measure belt slip speed and observe the limiting value float at constant speed when the slip just starts. 01 d cam analysis machine the apparatus is designed to study the cam profiles and performance of cam and follower system. the apparatus consists of a shaft supported by ball bearings upon which three different types of cams be mounted. the push rod for follower is supported vertically, which can adopt three different types of followers. cams and followers can be changed easily. a variable speed motor rotates the cam. a dial gauge permits plotting of follower displacement with respect to cam position. by operating the system at different speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. jump can be visualized also with the help of an optional stroboscope. specifications: · cam eccentric, tangent and circular arc type one each · follower mushroom, flat faced end roller type one each · cams and followers are hardened to reduce wear of the surfaces. · variable speed motor coupled to cam shaft of suitable range and variac · a dial gauge to note the follower displacement 01 e epicyclic gear train and torque holding apparatus it is a motorized unit consisting of sun gear mounted on input shaft. these planet gears are mounted on a common arm to which output shaft is fitted. loading arrangement is provided for loading the system and to measure holding torque. specifications external type epicyclic gear train: bearing blocks for input & output shafts a gear train with holding drum and holding internal typo epicyclic gear train: a compact gear train. variable speed d.c. motor rope brake arrangement to measure output torque and holding torque. control panel comprising of : digital ammeter and voltmeter. rpm indicator. speed controller. 01 f motorized gyroscope 01 the apparatus consists of a rotor mounted in bearings, this rotor is free to rotate about a. its own axis i.e. axis of spin. b. axis at precession. c. axis of gyroscopic couple the rotor is connected to the variable speed motor. the weight of the motor is balanced by another weight which is on either side of the rotor, by putting weights on the weight platform torque can be supplied to rotor, which is also called gyroscopic couple specifications: rotor diameter 250mm free about 3 axis of rotation driven by variable speed motor. dimmer stat to control the motor speed. stopwatch to measure the angular speed about the axis of procession. weights: 0.2kg, 0.5kg, 1kg. g motorized governor apparatus the unit consists of a main spindle driven by a variable speed motor. three different governor assemblies can be mounted over the spindle. pointer measures the lift of the governor. students can calculate characteristic of governor and compare their performance viz. sensitivities, stability, governor effort, etc specifications governor assemblies hartnell, porter& porpel governor assembly one each with rotating weights. variable speed fhp d.c. motor to drive the main spindle. sliding weights for porter & proell governor. scale & a pointer to measure governor lift. spring & spring compression adjustment arrangement. 01 h static & dynamic balancing apparatus. equipment is designed for carrying out the experiment for balancing 8 rotation mass systems. the apparatus consists of a stainless steel shaft fixed in a rectangular frame. a set of four blocks with a clamping arrangement is provided for static balancing. each block is individually clamped on shaft and its relative weight is found out using cord and container system in terms of number of steel bans. for dynamic balancing a moment polygon is drawn using relative weights and angular and axial position of blocks is determined. the block are clamped on shaft is rotated by a motor to check dynamic balance of the system. the system is provided with angular and longitudinal scales and is suspended with chains for dynamic balancing. experiments: 1. to balance the masses statically and dynamically of a single rotating mass system. 2. to observe the effect of unbalance in a rotating mass system. technical specification drive motor fhp motor, variable speed, with speed controller balancing weight 4 nos. of stainless steel with different sized eccentric mass for varying unbalance rotating shaft – material stainless steel 0.5 kw, 220v, single phase 01 i bar pendulum or compound pendulum 01 j rope brake dynamometer 01 k prony brake dynamometer 01 l whirling of shaft apparatus. the unit consists of a base upon which the bearing holders and driving motor and bearing can be fitted in a holders to end conditions of test shafts. a variac provides control of driving motor. the unit demonstrates the phenomenon of whirling of shafts with single rotor as the test is destructive after the test same shaft cannot be used again, hence the unit only demonstrates the principle. specifications: test shaft: 4.75 mm, 6.35 mm and 7.9 mm 2 each. bearing to provided end conditions, (a) both ends fixed, (b) one end fixed and one end free. drive motor 1/8 hp. 1500 rpm with control arrangement. the whole unit is mounted on a sturdy base. rotor for each shaft of suitable size. 01 m journal bearing test rig description: 01 the apparatus consists of a plain steel shaft excavated in a bearing and directly driven by a fhp motor. the bearing is freely supported on the shaft and sealed at the motor end. the speed of the motor is controlled by the speed control unit. manometer is mounted on bearing to measure the pressure at different position around the circumference. bearing is free to rotate and can be adjusted at any position of circular scale. the bearing can be loaded by attaching weights to the arm supported beneath it. technical details: journal : diameter 50 mm bearing : diameter 55 mm weights : 4 weights. motor : variable speed fhp motor control panel : for speed control of motor. oil recommended : sae 40 manometer : 16 tube manometer instruction manual : an english instruction manual will be provided along with the apparatus. the whole set up is well designed and arranged in a good quality painted structure. experimentation: to study the pressure profile of lubricating oil at various conditions of load and speed. plotting the cartesian polar pressure curves. 5 single cylinder four stroke petrol engine test rig the setup consists of single cylinder, four stroke, petrol engine connected to eddy current dynamometer for engine loading. the setup has stand‐alone type independent panel box consisting of air box, fuel tank, manometer, fuel measuring unit, digital speed indicator and digital temperature indicator. the setup enables study of engine for brake power, bmep, brake thermal efficiency, volumetric efficiency, specific fuel consumption, air fuel ratio and heat balance. provision is also made for conducting morse test. set up is supplied with ms excel program for engine performance analysis. self calculation and graphs sheets with excel programmings for comparison. solution tabs as reference for online diagnostics to problems. almost components from highly reputed mnc and international imports. self calibration/check techniques available specification: engine: make ‐honda, model ‐honda gx200d qx, type‐single cylinder, 4 stroke petrol, air cooled, 4.1 kw at 3600 rpm, stroke 54 mm, bore 68mm. capacity 196 cc dynamometer: type eddy current, water cooled propeller shaft: with universal joints air box: m s fabricated with orifice meter and manometer fuel tank: capacity 15 lit with glass fuel metering column rpm indicator: digital with non contact type speed sensor temperature sensor: type thermocouple, type k temperature indicator: digital, range 0‐1200 deg c load indicator: digital, range 0‐50 kg, supply 230vac load sensor: load cell, type strain gauge, range 0‐50 kg...

Military Engineer Services - Bihar

33366200 repair / maintenance of gyser at af stn bihta 1 material and labour for taking down of electric water heater / geyser from wall of capacity 25 / 50ltrs, dismantling / opening the same, servicing, cleaning and replacement of wornout, ms nut bolts, washers, clamps etc and made functional fully assembling, connected and testingcomplete all as specified and as directed. 2 material and labour for replacement of the following items required in repairs incorporated against items no19 abovecomplete all as specified and as directed. ( a ) elect water heater element 2 / 1.5kw as per existing size and specification 3 ( b ) apparatus ( syphon assembly ) plate as per existing size and specification complete all as specified and as directed. 4 ( c ) thermostate switch 30 70ºc ranging.as per existing size and specification complete all as specified and as directed. 5 ( d ) copper vessal ( inner tank ) of weighting 3.5kg suitable for water heater 25 ltr capacity complete all as specified and as directed. 6 ( e ) ss vessal ( inner tank ) suitable for 25 ltrs capacity water heater complete all as specified and as directed. 7 ( f ) copper vesal ( inner tank ) of weighting 4.5kg suitable for 50ltrs capacity water heater complete all as specified and as directed. 8 ( g ) ss vessal ( inner tank ) heavy duty suitable for 50ltrs capacity water heater complete all as specified and as directed. 9 ( h ) indicator lamp neon type 230w and all as per sample complete all as specified and as directed. 10 m&l for non return valves cast copper alloy isi mark 15 mm diaincluding taking out the old one complete all as required and complete all as specified and as directed. 11 m&l pressure release valve of brass inner threaded of 15 mm diaor as per sample approved by eicincluding taking out the old one complete all as specified and as directed. 12 m&l pressure release valve of brass outer threaded of 15 mm dia or as per sample approved by eicincluding taking out the old one complete all as specified and as directed. 13 s & f heavy duty steel bedded pvc polythene connection with 15mm dia 450mm long with cp brass nuts and leads pvc washer 02 nos on each endsfor hot waterincluding taking out the old one complete all as specified and directed. 14 s & f heavy duty steel bedded pvc polythene connection with 15mm dia 450mm long with cp brass nuts and leads pvc washer completefor cold water completeincluding taking out the old one complete all as specified and as directed. 15 m & l pvc insulated copper cable 3 core 40 / 0.0076, ac 1100 / 660 volt including taking down u / s cable complete all as specified and as directed. 16 m & lmetallic fastener screw 75mm long 6mm dia with bolt for hanging geyser, complete all as specified and as directed. 17 m&l painting of complete outer body of storage type geyser of capacity 25 to 50 litres with one coat of red oxide primer with two coat of synthetic enameled paint including preparing surface and including writing of mes no with black paint complete all as specified and as directed. 18 m&l gi tubing 15 mm dia medium gradeisi marked, laid in trench / floor or fixed on wall with all fixingaccessories etc complete all as specified and as directed. 19 m&l for multifunction safety valve cast copper alloy 15 mm dia isi markedincluding taking out the old one complete all as specified and as directed. 20 m&l forwater tapecast copper alloy 15 mm dia isi markedincluding taking out the old one complete all as specified and as directed. 21 s&f switch piano flush button single pole one way 15 amp, 240 volts conforming to is 3854 isi marked including taking down old one complete all as specified and as directed. 22 supply and replacement of rubber gasket flange as per site requirement for 25 / 50 ltr geyserincluding taking out the old one complete all as specified and as directed. 23 s & f sub main wiring using approved colour coding ( phase red, neutral black, earth green ) complete with two single core frls pvc insulated and unshealthedstranded copper conductor cable 6 sqmmas current carrying conductor and one run of 6.0 sqmm as earth contunity conductor , voltage rating 1100 volt , isi marked drawn in and including concealed pvc conduit isi marked of dia not less than 25 mm and thickness 2 mm with stranded accessories along with one run of frls pvc green colour insulated, unshealthed, stranded copper conductor of size 6 sqmm all as specified and directedincluding taking down old one complete all as specified and as directed. note: two run of single core frls pvc cable with one run of earth contunity conductor and conduit shall be measured as one unit. 24 s & f sub main wiring using approved colour coding ( phase red, neutral black, earth green ) complete with two single core frls pvc insulated and unshealthedstranded copper conductor cable 4 sqmmas current carrying conductor and one run of 4.0 sqmm as earth contunity conductor , voltage rating 1100 volt , isi marked drawn in and including concealed pvc conduit isi marked of dia not less than 25 mm and thickness 2 mm with stranded accessories along with one run of frls pvc green colour insulated, unshealthed, stranded copper conductor of size 4 sqmm all as specified and directedincluding taking down old one complete all as specified and as directed. note: two run of single core frls pvc cable with one run of earth contunity conductor and conduit shall be measured as one unit. 25 s&f mcb’s single pole, 10 ka , 6 amp to 30 amp 240 volts, and of c series with required wiring connections and lugs etc and erecting in provided enclouser / destribution board.mcbs shall be of current limiting type , isi marked conforming to is 8828 1996.the power loss per pole shall be low and shall be in accordance with is 8828 1996, all cable entries shall be either from bottom or top .mcb shall be of c curve charactertics & shall have quick make and break non welding self wiping silver alloy contact for 10 ka short circuit both on manual & automatic operation .including taking down old one complete all as specified and as directed. 26 s& f electric water heater storage type steel body with copper inner trank and heating element upto 2 kw capacity 25 litre bee 5 star rated complete with alkll accessories such as safety valve , thermostat , nrv connection piece etc. including taking down old one complete all as specified and as directed. 27 s&f mcb’s single pole and neutral, 10 ka , 32 amp to 40 amp 240 volts, and of c series with required wiring connections and lugs etc and erecting in provided enclouser / destribution board.mcbs shall be of current limiting type , isi marked conforming to is 8828 1996.the power loss per pole shall be low and shall be in accordance with is 8828 1996, all cable entries shall be either from bottom or top .mcb shall be of c curve charactertics & shall have quick make and break non welding self wiping silver alloy contact for 10 ka short circuit both on manual & automatic operation .all the active , live parts of mcbs should be out of human reach , ensuring safty & conforming to ip 55 degree of protection . including taking down old one complete all as specified and as directed. 28 s&f sheet metalenclosure with socket plug top and mcbs single pole with a two pin and earth plug andsocket complete with one single pole mcb ofc series of cap 16 32 ampincluding taking out the old one complete all as specified and as directed. 29 supply and fix switch socket combo of capacity of 15 / 16 amps with suitable make incl taking out old one complete all as specified and as directed. 30 supply and fix top plug of capacity 05 / 06 amps with suitable make incl taking out old one as complete all as specified and as directed. 31 supply and fix top plug of capacity 15 / 16 amps with suitable make incl taking out old one complete all as specified and as directed. 32 taking down old unserviceable mccb db tpn and supply, fixing and connecting up complete mccb db tpn 4 way ( vertical ) , double door, 415 v, ac, 50 hz, with and includingmccb32 amps 16 ka , ip 40 protection conforming to is 13032 universal mounting with copper bus bar, neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides complete all as specified and as directed. 33 s&f lamp holder pvc / polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. 34 s&f street light fitting 45 watt 230 v ac outdoor type high pressure die cast aluminum housiong and heat resistant complete with driver , lamp bracket with imapoact bracket and corrosive resistant incl thermal management complete with ip 65 protection complete all as specified and as directed. 35 s&f flexible wire including taking out the old one complete all as specified and as directed....

Eastern Railways - Bihar

31967085 supply of procurement of door way cross bar etc.procurement of door way cross bar etc.,door way cross bar pressing with back plate and packing piece in assembled condition to r.d.s.os drg. no. wd 80007 s 05, item no.2,14 & 15, alt no.28 (twenty eight)....

Eastern Railways - Bihar

27672747 supply of procurement of door way cross bar pressing with back plate and packing piece in assembled condition etc.procurement of door way cross bar pressing with back plate and packing piece in assembled condition etc., door way cross bar pressing with back plate and packing piece in assembled condition to rdsos drg. no. wd 80007 s 05, item no.2, 14 & 15, alt no.25...

National Thermal Power Corporation Limited - Bihar

26169049 supply of rc feeder spares of stage 2 and 3 mill at farakka stps . , back plate of stock feeder , bushing for coal feeder , grease retainer , grease seal outer , grease seal inner , grease retainer , seal ( cam side ) for gear box , seal ( cem side ) , seal ( worm gear shaft out put end ) coc , seal ( worm gear shaft output end ) coc , bearing cover for head pulley , bushing for coal feeder , bearing retainer for head pulley , drive sprockets rc60 , f1 / cms / a301792 , driven sprockets rc60 72t 3 , stage i feeder back plate , f1cmsa302901 . , stud & nut with body nut , f1 / cmsa303047 , stud & nut , f1cmsa303045 , shear pin for 1 w9009 gear box , torque arm for coc , take up screw for take up block , worm gear shaft for feeder drive gb , pin for head pulley of stock feeder , bearing cover for head pulley , bearing housing assembly for inlet span , bearing housing for weigh span roller , bearing housing casing for weigh span , roller for bunker outlet valve , gating assembly for coal valve , bushing for coal feeder , half coupling , take up drive block , screw take up , belt takeup screw block coal feeder belt , cover plate for main drive reducer , shaft tension roll 500 mw coal feeder , chain pin; , drive shaft & sprocket assly . for coc , belt take up block of stock feeder...

Eastern Railways - Bihar

23954950 supply of , back plate bolster to rdsos drg. no.wd 01065 s 02, item no. 2 , alt no. 2....

Eastern Railways - Bihar

23150011 supply of procurement of door way cross bar., door way cross bar pressing with back plate and packing piece in assembled condition for boxn wagon as per rdso drg. no. wd 80007 s 05,item 2,14 & 15, alt 24....

Indian Railway - Bihar

17662001 tender for back plate bolster drg no.wd 01065 s 02 item no 02 alt 02 or latest...

Eastern Railways - Bihar

17109678 tender for door way cross bar pressing with back plate and packing piece in assembled condition for boxnwagon as per rdso drg. no. wd 80007 s 05,item 2,14 & 15, alt 24 or latest....

Eastern Railways - Bihar

16700016 tender for door way cross bar pressing with back plate and packing piece in assembled condition for boxnwagon as per rdsos drg. no. wd 80007 s 05,item no. 2,14 & 15, alt no. 24....