All India Institute Of Medical Sciences - Bihar

38953253 tender for supply and installation of ht cable from substation 4a to substation 5 at aiims patna ; 1 supplying of under ground power cable 3core 300sqmm stranded circular aluminium conductor, conductor screen with extruded semi conducting compound, xlpe insulated, inuslation screening with extruded semi conducting compound in combination with copper tape, cross laid up, innersheath of pvc, galvenised steel flat strip armoured & overall pvc sheathed cable confirming to is 7098 ( part 2 ) 2011 with upto date amendmets suitable for 11kv ( make havells model aluminium conductor a2xfy / / rr / polycab or similar / superior ) 2 supplyingandinstallingfollowingsizeofperforatedpaintedwith powder coating m.s. cable trays with perforation not more than17.5%, inconvenientsections, joinedwithconnectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width x 50 mm depth x 1.6 mm thickness 3 layingandfixingofonenumberpvcinsulatedandpvc sheathed / xlpe power cable of 1.1 kv grade of following size on cable tray as required.above185sq.mmandupto400 sq.mm ( clampedwith 40x3mm ms flat clamp ) 4 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cmx50cmat thetopwithathicknessof10cmincluding inscription duly engraved as required. 5 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. 6 laying of one number pvc insulated and pvc sheathed / xlpe powercableof11kvgradeoffollowingsizedirect inground includingexcavation, sandcushioning, protectivecoveringand refilling the trench etc as required.above 120 sq. mm and upto 400 sq. mm 7 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 11 kv grade of following size in the existing rcc / hume / metal pipe as required. above 120 sq. mm and upto 400 sq. mm 8 laying of one number pvc insulated and pvc sheathed / xlpe powercableof11kvgradeoffollowingsizeintheexisting masonry open duct as required.above 120 sq. mm and upto 400 sq. mm 9 supplyingandmakingindoorcableendterminationwithheat shrinkablejointingkitcompletewithallaccessoriesincluding lugssuitableforfollowingsizeof3core, xlpealuminium conductor cable of 11 kv grade as required : 300 sq mm 10 supplying and making outdoor cable end termination with heat shrinkablejointingkitcompletewithallaccessoriesincluding lugssuitableforfollowingsizeof3core, xlpealuminium conductor cable of 11 kv grade as required : 300 sq mm 11 supplying and making straight through cable jointing with heat shrinkablejointingkitcompletewithallaccessoriesincluding ferrulessuitableforfollowingsizeof3core, xlpe aluminium conductor cable of 11 kv grade as required : 300 sq. mm 12 supplying and laying of following size dwc hdpe pipe isi marked alongwithallaccessorieslikesocket, bend, couplersetc. conforming to is 14930, part ii complete with fitting and cutting, jointing etc.direct in ground ( 75 cm below ground level ) including excavation andrefilling the trenchbut excludingsandcushioning and protective covering etc., complete as required.160 mm dia ( od 160 mm & id 135 mm nominal ) 13 excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returningthe soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : all kinds of soil pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm 14 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 15 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) derived from natural sources : 8 graded stone aggregate 40 mmnominal size derived from natural sources ) 16 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level : 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources ) 17 centering and shuttering including strutting, propping etc. and removal of form for lintels, beams, plinth beams, girders, bressumers and cantilevers 18 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.thermo mechanically treated bars of grade fe 500d or more 19 half brick masonry with common burnt clay f .p .s. ( non modular ) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) 20 finishing12 mm cement plaster of mix : 1:6 ( 1 cement: 6 fine sand ) 21 road workdry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete :with common burnt clay f .p .s. ( non modular ) bricks of class designation 7.5...

Ministry Of Power - Bihar

38801395 bids are invited for tools and tackels tools1 , tools2 , tools3 , tools4 , tools5 , tools6 , tools7 , tools8 , tools9 , tools10 , tools11 , tools12 , tools13 , tools14 , tools15 , tools16 , tools17 , tools18 , tools19 , tools20 , tools21 , tools22 , tools23 , tools24 , tools25 , tools26 , tools27 , tools28 , tools29 , tools30 , tools31 , tools32 non sparkling 8x9 ring & de spanner set non sparkling 10x11 ring & de spanner set non sparkling 12x13 ring & de spanner set non sparkling 14x15 ring & de spanner set non sparkling 16x17 ring & de spanner set non sparkling 18x19ring & de spanner set non sparkling 21x23ring & de spanner set non sparkling 24x27 ring & de spanner set non sparkling 25x28 ring & de spanner set non sparkling 30x32 ring & de spanner set non sparkling 36x41 ring & de spanner set non sparkling 46x50 ring & de spanner set non sparkling flat file 300mm non sparkling half round file 300mm non sparkling round file 300mm non sparkling center punch 150mm non sparkling combination pliers 200mm non sparkling adjustable wrench 300mm non sparkling pipe wrench 300mm non sparkling pipe wrench 600mm non sparkling socket set 1 / 2inch sq. socket ( mm ) non sparkling sledge hammer 2000gm non sparkling external circlip plier 300mm non sparkling internal circlip plier 300mm non sparkling flat screw drivers with blade 400mm flat screw drivers with blade 300mm precision screw driver set ( 6 pcs ) tapper guage 0 15 mm tapper guage 15 30 mm 200x200x450mm, 5compartments cantilever tool box sand paper 400 grit wet and dry sand paper 1200 grit wet and dry total quantity : 176...

Police Department - Bihar

37763515 tender for supply of computer table wooden, computer table iron, ladder arm chair, cantilever chair, ladder wing chair, computer operator chair, folding chair, executive chair, executive table wooden, center table wooden, waiting room seat iron, woodan outdoor chair, dining room chair, godrej almirah, ladder sofa, wooden wadrobe, wooden almirah, iron rack, wooden rack, dining room table, conference table with chair wooden, coffee table (wooden, glass, etc), bookcase (wooden, iron etc), vacuum cleaner, bedside table, wall shelves, shoe rack, revolving chair, office table wooden, dressing table, edura bed set wooden, clothes valet, recliner, dining wooden table, high back revolving chair, plastic chair, plastic table, rolltop desk, tv tray table and wooden stool...

Military Engineer Services - Bihar

37044332 tender for special repair to omqs / smqs at af station bihta 1 excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 m deep and getting out including forming bottom surface for laying of pipes complete all as specified and directed. 2 returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 mm thick complete all as specified and directed. 3 removal of excavated material to a distance not exc 50 meter and depositing wheredirected at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 4 supplying, laying and cushioning for cable protection in trenches 8 cm deep before laying cable and 15 cm deep over the cable including well punning complete all as specified and dierected 5 m&l cement concrete 1:5:10 type e2, using 40 mm graded stone coarse aggregate in sunken floor, all as specified and directed 6 m&lreinforced cement concrete (1:2:4) type b 1, (20 mm graded aggregate) as in slab supported on walls, beam, column and in similar work, complete all as specified and directed. 7 s & f for factory made solid pvc door frame of size 50mm x 47mm made out of 5mm plain colour pvc sheet, reinforced with ms square tube fixed in opening complete as per manufacturers specifications and as directed. 8 s & f for 30 mm thick factory made solid panel pvc door shutter conferming to criteria of testing as per is : 4020, consisting of frame made out of ms tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails ms frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded pvc `c channel of size 30x50mm forming styles and 5mm thick 75mm wide pvc sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross pvc sheet as gap insert for top rail and bottom rail panelling of 5 mm thick pvc sheet to be fitted in the ms frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick pvc sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick pvc strip of 20 mm width is to be struck on the interior side of c channel using pvc solvent adhesive complete as per manufacturers specifications & drawings & all as directed. 9 s & f pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete as specified. 10 s & f pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified. 11 m & l for pcc 1:3:6 type c 0 using 12.5mm aggregate crushed stone aggregate as in filling back side of pressed steel door/window frames, all as specified & directed. 12 s&f glazed/wire gauged/skeleton shutter 35 mm thick out of (well kilnseasoned)2nd class hard wood (hollock) the size of rails and style as per is chemically pressure treated in factory gainst termite infestation prepared to receive wire gauge (without sash bars) edges of frame chamfered or rounded fitted with cut and mitered beads, all as specified & directed.(note : wire gauge/glazing to be measured and paid separately). 13 s&f factory made 40 mm thick plain, framed, panelled shutter (two panel) with lock rail using 2nd class hw (hollock) kiln seasoned andchemicallypressure treated the size of rail and style as per is 1003 (part i) and panel insert of 9mm thick bwp commercial facing plywood or 12mm veneered particle boards with commercial ply all as specified 14 s&f plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed in 2nd class hardwood. 15 s&f of 25 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both sides all as specified and as directed. 16 s&f in repairs of 12 mm thick plywood, grade bwr, type bb, fixed with screws to timber frame work etc. in built in cupboard complete all as specified and as directed. 17 s&f for 100mm long mild steel butt hinges, heavy weight cold rolled mild steel, all as specified and as directed. 18 s&f for 75mm long mild steel butt hinges, heavy weight cold rolled mild steel, all as specified and as directed. 19 s&f 150 mm long aluminium anodised handles, cast type, all as specified and as directed. 20 s&f for 150 mm long aluminium, anodised, barrel tower bolts of extruded section, all as specified and as directed. 21 s&f 300 mm long aluminium alloy, anodised, sliding dooor bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, all as specified and as directed. 22 s&f for 200 mm long aluminium, anodised, barrel tower bolts of extruded section, all as specified and as directed. 23 s&f mild steel 300 mm ordinary rat tail rod pattern springs including roller & rooler plate complete all as specified and as directed. 24 s&f floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 140mm, all as specified and as directed. 25 s&f hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws of 100 mm size, all as specified and as directed. 26 s&f in repairs of harrison rail mild steel chromium plated of 19/20mm dia for curtain rod fixed with two nos of brackets for each rail all as specified and as directed. 27 s&f mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm, all as specified and as directed. 28 s&f anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed. (note : minimum thickness of powder coating 50 micron). 29 s&f anodised aluminium powder coated window and ventilator shutters, hung type without sash bar, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. anodised aluminium fittings such as peg stays 150 mm long (01 no), hinges b 21 100 mm long (02 no), suitable handle (01 no) complete all as specified.(note : minimum thickness of powder coating 50 micron). 30 s&f sheet glass 4 mm thick ordinary quality & glazing with rubber gasket in square n.exc 0.5 sqm in each pane, all as specified and directed.. 31 s&f 3 mm thick figured glass, pinhead type in squares n.exc 0.50 sqm each pane, all as specified and directed. 32 m&lfor mild steel tmt bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete, all specified and directed. 33 s&f in repair 18mm thick celuka pvc sheet minimum 600 kg/cum density grade 1 quality of both side plain white colour rigidlam glossy finish fixed with screws, solvent cement/adhesive as per manufacturer instructions to make kitchen cabinet sides top and bottom and shelves inside the cabinet completeas per specifications and as directed. note: (i) cup board accessories ie fittings,handles,hinges, will be measured and paid under this schedule.(ii) quoted rates deem to be include fixing of cabinet on wall with appropriate rawl plug/ dash through fastener (hammer type).(iii) fabrication and installation of cabinet to be carried out by authorised vendor of manufacturer only. 34 s&f auto closing stainless steel (grade 304) hinges 35 mm of 0 crank (kh 001) or 8 crank (kh 002) openable at 110 degree for kitchen cabinet shutters all as specified & directed. 35 s&f stainless steel handles of 100 mm size for kitchen cabinet shutter complete all as specified. 36 m&l for app basedpolymeric water proofing membrane minimum weight 3 kg/ sqm and minimum 3mm thick reinforced with polyster non wove fabrick (weight not less than 150gms/sqm), laid with torched application with the strict supervision of manufacturers technical supervisor, laid over hot blown bitumen 85/25 grade @1.2 kg per sqm over bitumen primer @0.30 ltr/sqm including cleaning surface, complete all as specified and directed.(note membrane shall be laid with 100mm side/end lap on prepared surface as per manufacturer instruction work shall be carried out strictly with the technical tradesmen and supervision of technical staff of manufacturer) 37 m&l for 40 mm thick brick tiles laid on bedding of 15 mm thick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) on treated roof all as specified and as directed 38 m&l for applying bituminous primer @ 0.40 kg/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm as in sunken complete all as specified including fixing of 40 mm dia gi spout pipe at bottom of slab/plastered surface etc, all as specified & directed. 39 roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, all as specified & directed. 40 m&l for providing cement concrete type b 1, 1:2:4 (20 mm graded aggregate) as in roof padding, roof kerbs (rounded or chamfered on edge) etc all as specified & directed. 41 m&l 75 mm thick cement concrete type d 2, 1:4:8 (using 40 mm graded aggregate) as in subbase to floor, ll as specified and directed.. 42 m&l for 25 mm thick cement concrete type b 0, 1:2:4 (12.5 mm graded aggregate) as on floor, ll as specified and directed.. 43 m & lnon skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15 mm thick screed bed in cement mortar 1:6 all as specified and directed. 44 m & lnon skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15 mm thick screed bed 1:6 all as specified and directed. 45 m & l glazed ceramic coloured tiles of approved quality isi marked (450 x 300 x 7 mm / 350 x 250 x 7 mmthick) as in vertical surfaces such as skirting dados etc set jointed in neat cement slurry and pointed in coloured cement to match with the tiles including 1:4 cement plaster 10 mm thick on brick work and concrete surface, all as specified and directed. 46 m&l for 15 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms (including a hole of gas pipe) and like including 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, all as specified and directed. 47 rounding to edges of stone slabs one edge, such as in steps, cooking platform, and similar situations, all as specified and directed.. 48 m&l for rendering 10 mm thick in cement mortor 1:4 on fair faces of brick work, surfaces finished even and fair without using extra cementwith water proofing compound, all as specified and directed. (note : wpc shall be measured and paid seperatelly). 49 m&l for 10 mm thick rendering in cement mortor (1:6) on air faces of brick work, surfaces finished even and smooth without using extra cement cement, all as specified and directed 50 m & l for 15 mm thick rendering in cm (1:4) on vertical surfaces of brick walls finished even and smooth without using extra cement with using water proofing compound, all as specified & directed. (note wpc will be measured and paid separately). 51 m&l for 5 mm thick rendering in cm (1:3) on ceiling surfacesoffinished even and fair without using extra cement, all as specified & directed.. 52 supply only integral water proofing compound 53 s&f 15 mm gi tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors including taking up or down old steel tube complete all as specified and directed. 54 s&f 20 mm gi tubes medium grade with all fitting and fixed complete to walls, ceilings or laid infloors including taking up or down old steel tube complete all as specified and directed. 55 m&l for preparation of new wood basesurfaces of any description, over 10 cm in width or girth, not otherwise described and appling twocoats of synthetic enamel paint (ordinary tint) overone coats of pink primer, all as specified and directed. 56 m&l peparation of old painted wooden surfaes of any dscription over 10cm width or girth and applying one coatof synthetic enamel paint complete all as specified and as directed. 57 m&l peparation of old painted steel surfaces of any description over 10cmwidth or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. 58 m&l for preparation of new plastered surfaces of ceiling and applying three coats of white wash all as specified and directed. 59 m&l for preparation of old surfaces of ceiling and applying two coats of white washall as specified and directed. 60 m&l for preparation of new plastered surfaces of wall and applying three coats of white wash all as specified and directed. 61 m&l for preparation of old decorated plasteredsurfaces of wall and applying two coat of white wash all as specified and directed. 62 m&l for preparation of new plastered surfaces of wall and applying two coats oil bound distemper over a coat of alkali resistant primer over a coat of 1 mm thick wall care putty in two different layers complete all as specified & as directed.(note treatment slall be carried our by spraying with mechanical means) 63 m&l for complete removal of existing treatment of wall and applying two coats oil bound distemper over a coat of alkali resistant primer over a coat of 1 mm thick wall care putty in two different layers complete all as specified & as directed.(note treatment slall be carried our by spraying with mechanical means) 64 m&l for complete removing of existing treatment of wall surfaces by scrapping with mechanical sander (having mechanical vacuum mechanism)to make surface clean, free from dust, loose paint etc and applying two coat of cement base paint of different colours complete all as specified and directed. 65 m&l for preparation of new plastered surfaces of walls and applying two coat of cement base paint of any colours and pattern (two or more colours) complete all as specified and directed.(note : colour and pattern of paint will be directed by ge) 66 m&l for pvc (swr) pipe of 110 mm boresingle socketed in any length with rubber ring joint fixed to wall with suitable clamps of adequate numbers etc complete all as specified and directed. 67 s&fpvc swr bends 110 mm boreall as specified and directed. 68 s&f cast iron soil, waste pipe100 mm dia, sand cast, in any length with or without ear, with cement joint, laid in trenches, complete all as specified. 69 s&f cast iron soil, wastepipe100 mm dia, sand cast, in any length with or without ear, with cement joint, laid in trenches, complete all as specified. 70 s&f cast iron soil, waste and vent pipe100 mm dia, sand cast, in any length with or without ear, with cement joint, fixed on wall, complete all as specified. 71 s&f cast iron soil, waste and vent pipe100 mm dia, sand cast, in any length with or without ear, with cement joint, fixed on wall, complete all as specified & directed. 72 s & f in repairs of 100 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured), all as specified & directed.. 73 s & f in repairs of 75 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured), all as specified & directed.. 74 s&f cast iron cowls of 100 mm bore pipe, all as specified & directed. 75 s & f in repairs cast iron floor trap with chromium plated graating of 100 mm size including jointing to waste pipe with cement joints etc, all as specified & directed. 76 s&f soap dish brass chromium plated decorative type, size 160x90mm complete all as specifed and directed. 77 s&f 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick ac buildg board or commercial plywood and fixed to wooden plugs with cpbrass screws and cup washers complete all as specified and directed. 78 s&f in repairbrass chromium plated, tubular towel rails 20 mm dia, d type, 60cm long between flanges, completed all as specified and directed. 79 s&f in repair chromium plated 125 mm size shower rose with swivel joints, in square with cp long shank arm including fixing to steel pipe or union of 15 mm bore, complete all as specified and as directed. 80 s&f in repairs vitreous china squatting pan “orissa pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in ssr and including s&f trap set complete all as specified and directed. 81 s&f in repairs pvc flushing cistern 10 ltr capacity valve less syphonic action type low level with and including dual flushball valve float & handle, waste pipe & brackets complete set complete all as specified and directed. 82 s & f in repairvitreous china wash basin, flat back, size 630x450mm white, excluding waste coupling, chain & plug, ci prackets, pvc waste pipe 32 mm,and porcelain stopper but including brackets. 83 s&f in repair chromium plated fancy type, stop cock/angular cock, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed. 84 s&f in repair chromium plated concealed type, stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed. 85 s & f in repair 15mm bore chromium plated bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron or brass ferrule, complete all as specified and directed. 86 s&f sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12mm wide with chromium plated bracket guard and railing, 600mm long,complete all as specified and directed. 87 s & f in repair pillar taps fancy type(long body)cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe, complete all as specified and directed. 88 s&f in repairpvc connections 15mm size with ptmt nuts of length 450 mm, complete all as specified and as directed. 89 s&frotational moulded polythene water storage tank of capacity 500 ltrs (cylindrical/vertical with closed top), triple layer construction, isi marked, hoisted & fixed in position including followings : (i)20 mm gi pipe medium grade,over flow 450mm long.(ii) 20 mm gi pipe medium grade waste pipe 600mm long.(iii) 20 mm brass ball valve/float valves, high pressure & high density plastic ball screwed for iron pipe and fixed.(iv) 20 mm gun metal globe/gate valve with iron wheel head, screwed on both ends for fixing including one gi nipple(20mm bore). 90 s&f in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including pvcwaste pipe, cp waste coupling,bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified anddirected. 91 s&f 1mm thick stainless steel kitchen plate rack of size 750x 900mm best quality assembled with brass washer and nut and bolts including hooks (spoon/cup holders) complete all as specified & directed. 92 demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level), all as specified & directed..note : all demolished items/ debris to be removed out side of mod land. 93 demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, all as specified & directed..note : all demolished items/ debris to be removed out side of mod land. 94 demolition of reinforced cement concrete of any description & in any position, complete all as specified and directed. 95 dismantling of stone slabs and tiles of any description or thickness in floors aprons etc including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 96 dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises,all as specified and directed. 97 taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed 98 taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site all as specified and directed. 99 taking down chowkats or frame with shutter (without taking out shutter from the frame) exceeding 1.50 sqm and n exc 4.00 sqm each and removal from site all as specified and directed 100 taking down of shutters of any description exc 1.00 sqm but n. exc 2 sqm each, all as specified and directed 101 taiking up or down steel tubing and connections, 15 mm bore including cleaning, complete all as specified and directed. 102 taiking up or down steel tubing and connections, 20 mm bore including cleaning, complete all as specified and directed. 103 dismantling pvc water tankcapacity exceeding 250 but not exceeding 500 ltr, complete all as specified and directed. 104 taking down100/75 mm cast iron soil waste pipe (any size or patterns) moulding all fittings heads shoes, bends etc (measured over all as fixed along the confrece line over fittings and accessories), all as specified and directed. 105 taking down rain water pipes (any size or pattern) ,including all fittings all as specified and directted . 106 demolition of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc (each layer) laid, bedded and pointed in any mortar including removal of debris/muds etc complete all as specified and as directed.note : all demolished items/ debris to be removed out side of mod land. 107 demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and finally cleaning the surface with wire brush to remove old treatment to lay pcc padding, complete all as specified and directed..note : all demolished items/ debris to be removed out side of mod land 108 taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc, complete all as specified and directed. 109 taking down old unserviceable mcb db tpn4 way (vertical), double door, 415 v, ac, 50 hz, includingmcb63 amps 16 ka ,ip 40 protection conforming to is 13032 universal mounting with copper bus bar,neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides, complete all as specified & directed. 110 material and labour for concealed point wring for one light/fan/exhaust fan point controlled by 1 no,one way 5/6 amp switch ,using approved colour coding (phase red,neutral black,earth green) complete with frls pvc insulated and unshealthedstranded copper conductor cable 1.5 sqmm single coreconforming to is 694 including medium duty concealed unplasticised pvc conduit conforming to is 9537(part 3) and isi marked not less than 20 mm dia with concealed in wall pressed steel terminal box of not less than 2 mm thick of required size including painting terminal boxs inside and outside with two coat of synthetic enamle paint over one coat of red oxide primerwith top cover3 mm thickbakelight laminated sheetwith brass screws and cup washer with all assessories including frls pvc insulated and unshealthedstranded copper conductor cable 1.5 sqmm single core in green colouras earth wireconnected to earth dolly . complete all as specified and directed . 111 all as per item no 110 above butfor one 3 pin /5 pin socket outlet 5 amp controlled by 1 no one way 5/6 amp switch on same board along with other switches ,fan regulator etc. 112 all as per item no 110 above butfor one 3 pin /5 pin socket outlet 5 amp controlled by 1 no one way 5/6 amp switch on independent board. 113 all as per item no 110 above butfor one call bell/buzzer point controlled by one push button switch. 114 material and labour for point wring ,using approved colour coding (phase red,neutral black,earth green) complete for one socket outlet 15 amp on independent board with frls pvc insulated and unshealthedstranded copper conductor cable 2.5 sqmm single coreconforming to is 694 including medium duty concealed unplasticised pvc conduit conforming to is 9537(part 3) and isi marked not less than 20 mm dia with concealed in wall pressed steel terminal box of not less than 2 mm thick of required size including painting terminal boxs inside and outside with two coat of synthetic enamle paint over one coat of red oxide primerwith top cover3 mm thickbakelight laminated sheetwith brass screws and cup washer with all assessories including frls pvc insulated and unshealthedstranded copper conductor cable 2.5 sqmm single core in green colouras earth wireconnected to earth dolly complete all as specified and directed. 115 s&f switch piano flush button single pole one way 5/6 amp, 240 volts conforming to is 3854 isi marked all as specified and directed. 116 s&ffor socket outlet, 5 pin, 5/6 amp flush type conforming to is 1293 isi marked all as specified and directed. 117 s&f switch piano flush button single pole one way 15 amp, 240 volts conforming to is 3854 isi marked including taking down old one, all as specified and directed. 118 s&ffor socket outlet, 3 pin, 15 amp flush type conforming to is 1293 isi marked including taking down old one, all as specified and directed. 119 s&fceiling rose, surface bakelite,isolated bodythree terminals including taking down old one, all as specified and directed. 120 s&f lamp holder pvc/polycarbonate type with back plate suitable for batten fittings, all as specified and directed. 121 supply only led bulb of 09 watt complete all as specified and directed. 122 s&f forbell push flush type 5 a sp 240 v all as specified and directed. 123 s&fbell (ding dong) 230 volts, single pole all as specified and directed. 124 taking down ceiling fan including cable, dismantling blades and carry out mnr repair and fixing of damaged parts like capacitor, bushes, bearings and screws etc and keeping in safe custody of contractor up to re fixing in the same. all as specified & directed. 125 m&l for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust, all as specified and directed. 126 hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, all as specified and directed. 127 m & l for repair / rewinding of ceiling fand replacement of requisite spares like bush, bearing, down rod, capacitor, fan clamp, fan blade etc if necessary all as specified and directed. 128 m & l for repair / rewinding of exaust fand replacement of requisite spares like bush, bearing, capacitor, fan clamp, fan blade etc if necessary all as specified and directed. 129 supply and fixing led tube lights fitting 1x 18w, 220v, including led tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling roseand complete all as specified and directed. 130 supply and fixing led batten type tube light complete fitting 1x 10 w, 220v,connecting up with three core flexible copper conductor cable of suitable size from ceiling roseand complete all as specified and directed. 131 supply &fixing and connecting up complete mcb db tpn 4 way (vertical), double door, 415 v, ac, 50 hz, with and includingmcb63 amps 16 ka ,ip 40 protection conforming to is 13032 universal mounting with copper bus bar,neutral link, earth link, earthing studs, detachable gland plates with knockouts on both sides, complete all as specified & directed. 132 s&f sheet metal enclosures (mcb distribution board) when mcb’s to be used singlepole and neutral 8 ways 220 volt with 200 amps rated bus bar, double door with bus bar neutral link earth bar, din rail, necessary blanking plated, including fixing db flush in wall complete with making good disturbed surfaces and colour matching all as specified and directed including taking down old one, complete all as specified & directed. 133 s&f mcb’s single pole, 10 ka ,32 amp to 40 amp 240 volts,and of b series with required wiring connections and lugs etc and erecting in provided enclouser/destribution board.mcbs shall be of current limiting type ,isi marked conforming to is 8828 1996, including taking down old one, complete all as specified & directed. 134 s&f sheet metalenclosure with socket plug top and mcbs single pole with a two pin and earth plug andsocket complete with one single pole mcb ofc series of cap 20 amps including taking out the old one all as specified and directed. 135 s&f mcb’s dp, 10 ka, 32 amp to 40 amp 240 volts,and of b series with required wiring connections and lugs etc and erecting in provided enclouser/destribution board. mcbs shall be of current limiting type ,isi marked conforming to is 8828 1996,including taking down old one complete all as directed. 136 supply and fixing stud 10 w led lights energy saving bulk head luminaries including led light driver, holder connecting up with three core flexible copper conductor cable of suitable size from ceiling roseand complete all as specified and directed. 137 s&f sub main wiring using approved colour coding (phase red,neutral black,earth green) complete with two single core frls pvc insulated and unsheathedstranded copper conductor cable 6 sqmmas current carrying conductor and one run of 6.0 sqmm as neutral cable ,voltage rating 1100 volt ,isi marked drawn in and including concealed pvc conduit isi marked of dia not less than 25 mm and thickness 2 mm with stranded accessories along with one run of frls pvc green colour insulated,unshealthed,stranded copper conductor of size 6 sqmm all as specified and directedincluding taking down old one, complete all as specified and directed.(note: two run of single core frls pvc cable with one run of earth contunity conductor and conduit shall be measured as one unit.) 138 m&l for earthing complete with galvanized steel earth plate 600x600x6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire of 4mm dia as earthing lead by means of bolts, nuts, check nuts, and washers of galvanised iron or steel besides welding at all joints as shown in drawings and including excavation and earth work, gi pipe light grade 15 mm bore for protection of giwire from earth electrodeto test point /machinery / equipment.supplying and laying charcoal dustcomman saltpcc(1:2:4) type b1 using 20 mm gradedstone agregratechamber andrcc cover 54 cm x 54cm x50 mm thick (1:2:4) type b 1using 20 mm stone agrigrtae )reinforced with 8 mm dia tmt bars @75mm c/c both ways with mild steel handle 12 mm dia,using round bar ,pgi funnel with wire mesh, 20 mm dia gi pipe medium grade for watering all as shown in electrical plate no 3 of ssr part 1including testing and taking out the old one complete all as specified and directed(note cost of gi wire and gi protection pipe up to a distance 7.5 m shall be includedin quated rate of above items) 139 s&f 415 v, 10 ka ,b curve miniature circuit breaker mcb tpn 63 amps, 16 ka complete all as specified and directed. 140 supply, laying, connecting and testing xlpe cable underground pvc insulated and over all sheathed with aluminium conductor heavy duty 1100 volts grade 3.5 core 35 sqmm sizes, laid in trenches, floors, ducts passing through pipe forroad crossing etc including taking down old unsv cable of any size complete all as directed including taking out old damaged cable and all as specified and directed. (note excavation, earth work, brick protection sand cushioningand gi pipe etc shall be measured & paid for separately) 141 m&l for laying of bricks subclass ‘b’ old size having crushing strengh not s than 75 kg/sqcm, laid flat perpendicular to the direction of cable for protection of cable complete all as specified & directed. 142 m&l gi tubing 50 mm dia light grade, laid in trench/floor or fixed on wall with all fixingaccessories etc as specified and directed. ...

Bharat Heavy Electricals Limited - Bihar

36352061 supply of trench materials cable trays , supply trench material : ladder type tray, 2mm thick, hot dip galvanized cable tray 600mm wide , supply trench material : ladder type tray, 2mm thick, hot dip galvanized cable tray 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories 90° horizontal bend for cable tray 600mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories 90° horizontal bend for cable tray 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories 90° vertical bend (inside) for cable tray 600mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories 90° vertical bend (inside) for cable tray 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories 90° vertical bend (outside) for cable tray 600mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories 90° vertical bend (outside) for cable tray 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories horizontal tee for cable tray 600mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories horizontal tee for cable tray 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories horizontal cross for cable tray 600mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories horizontal cross for cable tray 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories right hand reducer for cable tray 600mm wide to 450mm wide , supply trench material : ladder type tray, cable trays, fittings and accessories left hand reducer for cable tray 600mm wide to 450mm wide , supply trench material : bolted assembly, vertical support single channel (c1) of length 450mm , supply trench material : bolted assembly, horizontal support cantilever arm (ca1) of length 650mm along with necessary base plate, bolts, nuts with long springs, washers, etc. required for fixing on vertical support channel. , supply trench material : bolted assembly, clamp cc1 suitable for single channel for fixing vertical support channel c1 along with necessary anchor/ rawl bolts/ spring nuts/ washer, etc. , supply trench material : panhead screws m6, m6 nut with long spring for fixing trays on support racks , supply trench material : tray fixing clamp (tc1)...

Building Construction Department - Bihar

35845259 tender for supplying and installing office chair of dimension 480x475x410 with 220 (+5mm) mm arm lenth, arm width 30mm +2mm, 390 mm back rest width of b series model b 84 round no revolving and non tilting with continuous armrest, chair frame cantilever type and padded seat and backrest, over flat size in depth wise of the frame on both side with minimum 3 screws and seat backrest fitted by round head screws 3nos (minimum) on each side, frame material of steal tube (erw quality) conforming to is:1161 (with latest amendments), rounded tubular section of frame, 25 mm diameter/ sides of frame, 1.6mm thick frame section wall thikness, cushion pad fixed on arm rest frame of 15 mm thickness, single piece of cold reduced carbon steel sheet confirming to grade cro of is: 513 part i (with latest amendments, seat material 15 mm thickness, backrest material thickness 12mm. color as per requirement, supplying and installing steel almirah of size 1981x916x486 mm multi band construction and inter locking design and full lenth over lapping doors and sides. three way bolting mechanism, spot welding & co2 welding anti corrosion treated components, oven backed power coating process. material thickness 0.9mm top, bottom, lh & rh sides and back material thickness= 0.9mm, removable rh & lh main door with stiffeners material thickness= 0.9mm, 4 adjustable shelves of thickness =0.8mm, supplying and installing 3 seater steel chrome chair cross beammade of ms erw rectangular black powder coated tube of 80 x 40 x 2 mm leg & arm rest chrome plated made of cold rolled steel. arm rest & leg assembled to the cross beam with m10 x 100 mm bolts. seat & back 1.6mm thick powder coated perforated shell of cold rolled ms sheet. side bar of chrome plated solid steel 30 x 12 mm (din 174) with flunting & plastic insert.the shell is assembled on the cross beam with help of m8 bolts the overall dimension is 1608mm (l) x 695mm (h) x 555mm (d), seat height: 405mm, providing & installing 250 lph capacity ro plant with 1 t water chiller plant i/c plumbering work in sub divisional court campus shahpur patori with all complete job as per direction of e.i. all the material must be of stander make up & specification....

East Central Railway - Bihar

35258024 supply of hydraulic manual scissor lift table platform, size 1800 mmx1200mm, closed height: 350mm +600 mm lifting height, load capacity 1000 kg. bill deck 30 mm steel ball with washer and proper fitting. cantilever 450 mm+200mm lip. wheel swivel with brake and fixed wheel handle t type detachable hyd pump type with handle. note %u2013material delivery at parcel office danapur and as desired by the consignee. comprehensive warranty of all parts of hydraulic manual scissor lifts 03 years. [ warranty period: 30 months after the date of delivery ] ...

East Central Railway - Bihar

35140323 supply of hydraulic manual scissor lift table platform.hydraulic manual scissor lift table platform., hydraulic manual scissor lift table platform ( size: 1800 mm x 1200 mm. closed height 350mm + 600mm lifting height, load capacity 1000 kg , ball deck 30mm steel ball with washer and proper fitting. cantilever 450mm + 200mm lipi wheel swive with brake and fixed wheel handle t type detachable hyd. pump type with handle or similar. [ warranty period: 30 months after the date of delivery ] => limited...

East Central Railway - Bihar

35089539 auction sale of scrap misc. items ferrous and n / ferrous ( 1 ) misc. ferrous, iron fittings, gi, nuts & bolts, cantilever, fe 2430.00kg ( 2 ) misc. copper, cu 60.00kg ( 3 ) contact wire, cu 150.00kg ( 4 ) catnary wire, cu 150kg ( 5 ) misc. brass / bronze, 100.00kg ( 1 5 ) location sse / trd / kms...

Science And Technology Information Institute - Bihar

35071146 bids are invited for b , st , dd , dt , uwco , ocb , pc , ecvcanv , smchr total quantity : 656 s.no. dst code description qty. 1 b hostel bed made out of steel with overall size length 1994mm, width 907mm, height 822/623/ rest height 450mm, structure of metal bed frame including legs and head structure mild steel pipe, head board shape of headboard semi circular, thickness of hollow section in structure (1.2mm), support panel for placement of mattresses mild steel hollow box rectangular section, thickness of support panel (in 1.2mm), material of head board mild steel erw tube is:7138 square tube of 38.1 mm x 1.2 mm thick, material of mattress panel ms perforated / sheet, thickness of mattress panel 1.2 (mm), size of support members in mm (±5 mm) 50 x 50mm, number of support members is 04 nos., paint /finish of all m s parts powder coating 60 micron. 150 2 st supply of desk and chair of size: length:600mm, width: 450mm, height: 750m. top made of 18 mm partical board , with injection molded ppcp edges. seat & back molded ppcp material. metallic structure consist of 40mm x 20mm x 16 guege oval tube. 6mm rod used for book shelf. 0.8mm metal sheet used for apron. 70 micron powder coating on metal structure. chair specification metallic structure consists of 40mm x 20mm x 16 guege and 35mm x 15mm x 16 guege. hdpe meterial is use in seat and back, 70 micron powder coating on metal structure. all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. 150 3 dd dual desk is specially designed for rugged use with overall dimentions of l1054 x w980 x h760 mm and all edges are fillet. the desk is made of pressed formed ms crca section & crca tube fitted with pre laminated particle board top, seat & back with injection molded ppcp edge. hanger for water bottle and bag. space for keeping pen, pencil and scale. the overall appearance of the product shall be as per photograph. top injection molded ppcp edge. size : 1054x450x18 mm thk. particle board. seat injection molded ppcp edge. seat height : 450 mm , seat size : 1054x304x18 mm thk. particle board. back injection molded ppcp edge. back size : 1054x154x18 mm thk. particle board. shelf shelf 0.8 mm thk. crca sheet. bullnose front edge with stiffner 1 mm thk crca. modesty modesty 0.8 mm thk. crca sheet. slot perforated. tie members horizontal tie members 25x25x1.2 mm thk. crca pipe. footrest footrest pressed formed crca section 1.5 mm thk. side frame side frame c section pressed formed 1 mm thk.crca sheet welded with 25x50x1.2 mm thk tube. and back rest pipe ø25 x 1.2 mm thk. cap & levellers all pipe caps are curved ppcp material. finish all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. 180 4 dt 4 seater pu coated size shall be 1135mm width x 1175mm depth x 750mm height. top shall be 25 mm thick base material shall be 25 mm mdf board. on top pu painting of minimum 2h hardness with 75% glass as per colour chart . white laminate on bottom specially profiled edges for comfort. thenunder structure shall be having bend pipe structure of ms powder coated. pipe dia 38 mm, 2 mm thick and it shall be fitted with top by ss machine screws. legs shall be of ms powder coated and 38 mm dia. pipe legs are fixed with under structure and table top. glide shall be of plastic fixed at the under structure to prevent the damage of table top during stacking . 8 technical specification page 1 of 2 s.no. dst code description qty. 5 uwc o computer chair with seat and back are made on injection moulded high impact strength polypropylene polymer compound with indoor graade uv resistance.the tubular weled frame is made from dia2.22 +/ 0.03cmx 0.12+/ 0.0128 cm and 3.5+/ 0.03 cm x 0.12+/ 0.0128 cm m.s.e.r.w. tube. the shoes are made of high impact strenght polypropylene polymer. compond with indoor grad uv resistance and pressed fitted with tubularfram. size : (w)52 cm*(d)55 cm*(h)84 cm* 60 6 oc b office chair: size: total height 840mm, depth 600mm, width 575mm seat height:450mm. under structure cantilever type ms cold rolled close annealed tube 1.6 mm thick. hot pressed ply wood with steel t nuts for rigid fastening. single piece integral skin pu arm rest. quality tapestry. seat and back covered with pp covers. high density pu moulded cushion. all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. 36 7 pc principal chair: overall size max/min. height 1285/1165mm, width 690mm, depth 700mm, seat height 640/520mm, seat size w 560mm x d 530mm, back size h 770mm x w 530mm, 5 prong nylon base for stability. twin wheel heavy duty castor for easy mobility under load. hot pressed ply wood with steel t nuts for rigid fastening. sturdy steel column gas lift for centre support and seat height adjustment. telescopic abs cover over steel column. lockable centre tilt mechanism and with single piece die castes nylon arm rest with cushion. quality latherite tapestry with single and double stitch. high density pu cushion. over all appearance of product as shown in picture. available in only black latherite. 3 8 ec vcanv visitor overall size height 1035mm, width 690mm, depth 690mm, seat height 490mm, seat size w 560mm x d 530mm, back size h 640mm x w 530mm, under structure cantilever type ms cold rolled close annealed tube dia. 32mm x 1.6 mm thick. hot pressed ply wood with steel t nuts for rigid fastening. single piece die castes nylon arm rest with cushion. quality latherite tapestry with single and double stitch. high density pu cushion. all steel components should be epoxy powder coated followed by seven tanks anti corrosion treatment of surface. the overall appearance of the product shall be as per photograph. available in only black latherite. 9 9 smchr chair with full tablet size: total height 850mm, seat height: 440mm, tablet height: 665mm, depth 270mm & width:550mm. under structure cantilever type ms cold rolled close annealed tube 1.6 mm thick. hot pressed ply wood with steel t nuts for rigid fastening. single piece integral skin pu arm rest. quality tapestry. high density pu moulded cushion. book rack made of plastic coated wire mesh fitted at bottom of seat and tablet made of 18mm thick pre laminated particle board. 60 page 2 of 2 ...

Department Of Science And Technology - Bihar

34872901 bids are invited for physics and chemistry lab items 1 to find the viscosity of a given liquid ( glycerin ) by stokes law. 2 to find the coefficient of linear expansion of the material of rod. 3 to determine atmospheric pressure at a place using fortins barometer 4 to determine and verify the time period of a cantilever 5 to determine velocity of ultrasonic in different liquids using ultrasonic interferometer. 6 to verify laws of resistances in series and parallel combination. 7 to find the frequency of ac main using electrical vibrator 8 to verify kirchhoffs law using electric circuits. 9 to convert a galvanometer into an ammeter. 10 to convert a galvanometer into a voltmeter. chemistry lab item 1 oxalic acid 2 sodium carbonate 3 phenophtal1n 4 hcl 5 112504 6 methyl orange 7 sodium hydroxide 8 formaldehyde solution 9 acetic acid 10 phenol 11 barium chloride 12 barium sulphate 13 cupric oxide 14 copper sulphate 15 sodium thiosulphate 16 sodium nitrate 17 methyl alcohalimethanol ) 18 lab solvent 19 acetone 20 distilled water 21 digital balance 22 measuring flask 23 funnel stand 24 magnet bar 25 titration flask 26 digital ph meter 27 muffale / electric furnace 28 dust bin...

East Central Railway - Bihar

33305843 auction sale of scrap ferrous and non ferrous(1)misc ferrous, stay turn buckle, no. plate,cantilever tube(bracket, stay, register), fe 1400kg(2)contact wire, cu 20kg(3)dropper, cu 10kg(4)feeder wire, al 50kg(5)bracket suspension, brass/bronze 100kg(1 5)location sse/trd/ohe/ddu...

Mother Dairy - Bihar

33008975 tender for civil work for: 1. engineering workshop and chemical storage (part 01) & 2. new boundary wall, labour toilet extension, etp equalization tank, treated water tank, new dock with cantilever shed, sludge drying bed, rcc road at tanker cleaning area and wtp to boiler and shed at bulk acid caustic preparation area (part 02). at mother dairy, motihari bihar plant....

Urban Development And Housing Department - Bihar

32366631 bids are invited for overhead cantilever gantry sign boardauto extension if any seller submits price in last 15 minutes, the rawill be auto extended by 15 minutes. ( a maximum of20 times ) total quantity : 7...

Building Construction Department - Bihar

31919687 provision of supply and installation of digital delegate unit flush mounted audio conference system for conference hall/audio controller system and digital delegate unit audio conference system/conference multicore cable for connecting conference units and digital delegate unit flush mounted consisting modular components audio conference system/digital wooden flooring and upvc work, veneered wood paneling work, double skin veneer partition toughed glass door, renovation of conference hall, provision supply and installation of fire alarm and fire extinguisher system for safety protection, vip cantilever chair furniture work, conference table, chair furniture work, loudspeaker amplifier, speaker cable, audio sound reinforcement system, intell digital mixer, audio processor, digital interface unit etc...

Department Of Science And Technology - Bihar

31795656 bids are invited for 1 flywheel 2 2 spring constant 4 3 inverse square law of radiation using photoelectric method ( inverse square law ) 1 4 v i charecterstic of semiconductor diode ( pn junction diode ch. apparatus 4 5 pn junction kit 2 6 he ne laser source and diffraction grating setup 1 7 terminal velocity measure stokes law setup 2 8 fortins barometer 1 9 mercury for fortins barometer. 1 10 mercury thermometer 5 11 ultrasonic interometer ( measuring device for velocity of ultra sonics 1 12 plain mirror 10 13 glass slab 75x50x18mm and prism50x50mm 10 14 convex lens 10 15 omhslaw apparatus 4 16 kirchoffs law verification kit ( electric circuit0 verification of kcl&kvl. 2 17 slide callipers 10 18 screw gauge 10 19 spherometer 10 20 wensar pbg gold balance 2 21 universal force table 2 22 hooks law apparatus with all accessories 4 23 cantilever set...

Building Construction Department - Bihar

31163433 estimate of furniture for new govt. engineering . college, khagaria 1 office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side one drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock. 2 2 seater sofa overall size 1130w x 700d x 785 h cm, seat height 43.5 cm side frame assembly: the side frame assembly is fitted to the two ends of the connecting beam assembly to form, the leg cum armrest assembly. it is made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick ms e.r.w. tube and powder coated ( dft 40 60 microns ). the ends are fitted with abs moulded end caps, 3. seatrest assembly:the seat rest assembly consists of a fabricated inner frame assembly insitu moulded high resilience (hr) polyurethane foam having density = 45 +/ 2 kg/m3 with hardness load 25 ± 2 kgf as per is:7888 for 25% compression of the foam. the complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover *seat size: 52.0cm. (w) x 50.0cm. (d) x 6.0cm. (t), 4. backrest assembly:the backrest assembly is flexing type and consists of a fabricated inner frame assembly insitu moulded with high resilience (hr) polyurethane foam having density = 45 +1 2 kg/m3 with hardness load 14 ± 2 kgf as per is:7888 for 25% compression of the foam. the complete moulded backrest assembly is covered with a replaceable fabric upholstery cover. *back size: 52.0cm. (w) x 59.0cm. (h) x 6.0cm. (t), 5. adj. glides: the adj glide is injection moulded in black nylon & fitted to the front end of side frame assembly along with abs moulded adj. glide base to take care or unleveled floor surface 3 3 seater sofa the side frame assembly made of 38mm dia 2mm thick is fitted to the two ends of the connecting beam assembly to form the leg cum armrest assembly. it is made of a ms. e.r.w. tube duly powder coated. the ends are fitted with abs moulded end caps. tie member: it is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. the tie member is made of ms. e.r.w. tube 40mmx40mm 2mm thick duly powder coated. the seat/back assemblies are mounted on the tie member. l bracket of 6mm thick steel connects the back to the tie member assembly. seat foam is of 45 +/ 5 kg/m3 and back foam is of 32 +/ 5 kg/m3 with hardness of 25+/ 2 on hampden m/c. at 25% compression of the foam. seat size 52cm widex50cm deep and back size 52 cm wide and 60cm high. back of the sofa flexes for additional comfort 1 seater –601mmwx700mmdx 810mmh, 3 seater –1640w x 700d x 785 h cm 4 3 seater steel chair cross beammade of ms erw rectangular black powder coated tube of 80 x 40 x 2 mm leg & arm rest chrome plated made of cold rolled steel. arm rest & leg assembled to the cross beam with m10 x 100 mm bolts. seat & back 1.6mm thick powdercoated perforated shell of cold rolled ms sheet. side bar of chrome plated solid steel 30 x 12 mm (din 174) with flunting & plastic insert .the shell is assembled on the cross beam with help of m8 bolts the overall dimension is 1608mm (l) x 695mm (h) x 555mm (d), seat height : 405mm 5 work bench of size 4’ x 3’, angle 1.5 x 1.5 with 2 pair of legs with work top with overall dimensions. 1200mm l x 900mm d x 950mm h, the worktop of mdf ext garde is12406 wood. max udl 1500kgs the worktop should be made of various layers of beech wood which are planed, glued and pressed together. this should make the work top non deformable, and load and wear resistant. this shall be covered with 4mm steel sheet. leg: the bench leg should be powder coated should be 80mm l x 1265mm d x 960mm h. back bracing for stability 6 centre table of size 1200w x 600d x 378h built with the extremely durable rubberwood, the table can hold weight up to 25kgs. with a very suitable cappuccino color, the table will complement any style of décor. the tapered legs provide stable support. it’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. the well thought out dimensions of the table make it easier to position it anywhere in the house 7 work bench of size 8’ x 4’ with 2 pair of legs with work top with overall dimensions. 2400mm l x 1200mm d x 950mm h, the worktop of mdf ext garde is12406 wood. max udl 1500kgs made of various layers of beech wood which are planed, glued and pressed together. this should make the work top non deformable, and load and wear resistant. bench leg: the bench leg should be powder coated should be 80mm l x 1265mm d x 960mm h. back bracing for stability 8 executive chair with cushioned seat is made of injection molded plastic outer & inner. plastic inner is upholstered with stitched cover and moulded high resilience polyurethane foam of density 4542 kg/m*,and hardness load 16 + 2 kgf as per 15:7888 for 25% compression.the stitched cover is made from spacer fabric and leatherette seat size : 47.0 cm. (w) x 48.0 cm. (d), tunular frame : the powder coated (dft 40 60 micron) tubular frame is cantilever type & made of 02.5440.03 cm x 0.240.016 cm thk ms erw tube.the back connected to frame through powder coated (dft 40 60 micron) high pressure die cast connector. 9 office chair with seat and back are made from seasoned wood and plywood. the same is upholstered with black synthetic leather and polyurethane foam. back size 46.0cm(w)x27.0cm(h). seat size 46.0cm(w)x40.0cm(h). the armrest is gas assisted injection moulded from black polypropylene. the understructure assembly is a cantilever type frame.width of the chair 58cm, depth 56.5cm,height 87.5cm,seat height 48cm. 10 office chair : the seat and back are made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per qa method described in ocp qlta p14 18 and upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the back foam is designed with contoured lumbar support for extra comfort. back size 49.0 cm. (w) x 47.0 cm. (h) , seat size 49.0 cm. (w) x 44.0 cm. (id) high resilience (hr) polyurethane foam: the hr polyurethane foam is moulded with density = 45 ±2 kg/m3 and hardness load 16 ± 2 kgf as per is:7888 for 25% compression. 11 principal chair: the seat is made up of 1.4± 0.1 chick hot press 4 plywood upholstered with fabric and moulded polyurethane foam. it has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. seat size: 50.0cm (w)x 49.0cm(d).the back is injection moulded in glass filled polyamide which is upholstered with mesh fabric. the back consist of adjustable lumbar support made of injection moulded polypropylene having an adjustment of 6.0±0.1cm.backsize: 50.0cm(w) x68.0 cm(h).the polyurethane foam for seat is of density 55± 5kg/m3. it is made of glass filled polyamide arm structure with pu arm top and height adjustment of 7.0 ±0.5cm.the arm top has swivel and to for movements. to for movement is 6.0± 0.5cm.the inner tube of armrest is chrome plated. the mechanism is designed with the following features:• 360° revolving type.• centre tilt synchro• 3 position (including upright lock) giving option of variable tilt angle to the chair with anti shock feature. the headrest is injection moulded din glass filled polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the full back chair. the pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.the pedestal is high pressure die cast polished aluminum and fitted with 5 nos. twin wheel castors. the pedestal is 65.0±0.5 cm p.c.d. the twin wheel castors are injection moulded in black glass filled polyamide having 6.0±0.1cm wheel diameter. the chrome plated tubular frame is made of día2.8±0.03cm x0.2±0.02 cm the m.s. round tube. the frame is fitted with plastic caps made of injection moulded glass filled polypropylene. 75(w)* 75(d)* 115 130(h)* 44.5 53.5(sh). 12 computer chair with seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade uv resistance.the tubular weled frame is made from dia2.22 +/ 0.03cmx 0.12+/ 0.0128 cm and 3.5+/ 0.03 cm x 0.12+/ 0.0128 am stainless steel 202 grade tube.the tube are buff polished to give shiny finish. cm. the shoes are made of high impact strenght polypropylene polymer. compond with indoor grad uv resistance and pressed fitted with tubularfram. size : (w)52.5cm*(d)55.8cm*(h)84.5cm*(seat h) 45.0 cmseat size 52.5cm(w)*53.2 cm(d) back size 51.6 cm(w)*40.5 cm (h). 13 office chair mid back pneumatic height adjustment cushioned revolving chair made up of 1.2cm thick hot pressed ply wood seat & back upholstered with fabric with moulded polyurethane foam together with moulded abs seat & back integral skin polyurethane with reinforced with m.s. insert. the tilt mechanism adjustment upright locking, 360 degree revolving type fitted with 05 nos. twin wheel castor dia 5 cm. 14 compactor on 12 feet rail length moves on rails. the cabinet body rigid knock down construction made of 0.8 thick crca steel eonforming to is: 513 gld. body units are bolted to undercarriage. optimizer height from ground is 2081] mm (1930 hody+ 65 under 35 channel systems] finish: — the bodies inciuding shelves are given anti rust surface treatment 8‘ are powder coated with epoxy polyester powder oven backed with a controlled temperature of 130 deg. to 200 deg. c.sheif:l made of 0.8 thick crca steel conforming to is;513 gd. max load bearing capacin is fit! kg. udl per ahett x 5:400 kg. eauh cabinet. undercarriage: the undercarriage is a welded trams made of hr sheet 3.15 mm thick conforming [0 is; 1d?48movement of the system: push pull configuration {type p utype f~2} movement of units achieved pushing or putting chrome plated 0 handle fitted suitable height on one side at body. 15 conference table of 30 seater capacity shall be an eco modular conference table enables various configurations to suit different conference rooms. it is made of particle board and has wire management facilities for uncluttered wiring. it has profiled legs with twin colored modesty for better looks, double 1350.0wx 600.0dx 750.0h, work surface top thickness is 25mm plb with pvc beading allover, legs modesty wire manager made from 18mm thick plt having curved profile.made from plt (prelaminated twin) boards 18mm thick in two shades. a wire manager running along the width of desk fitted on the modesty panel from inside. 16 corner table of size 530w x 450d x 450h built with the extremely durable rubberwood, with a very suitable cappuccino color, the table will complement any style of décor. the tapered legs provide stable support. it’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. the well thought out dimensions of the table make it easier to position it anywhere in the house. 17 dining table of 8 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical/data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309/7558 (black color). 18 file cabinet with 4 drawer width: 470mm, height: 1320mm, depth: 620mm , rigid knockdown construction, material: top, side & drawer frontmade from0.7mm thk **crca, drawer inside cover, side back side made from0.6mmthk **crca, back, bottom, drawer bottommade from 0.5mmthk **crca, **crcasteel confirming to is 513, grade d, label holder snap on type plastic label holder on drawer fronts, locking & anti tipping arrangement centralized lockingwith camlock& having antitipping arrangement to ensure that when one ,drawer is opened for use, it does not allow other drawers to be opened, finish epoxy polyester powder coated to the thickness of 50 microns (+/ 10). 19 fire proof cabinet shall be designed to protect the contents (paper media documents) against the fire hazard.shell: the external shell of the cabinet shall be of steel of minimum 2 mm thick and internal shell of steel of 1.6 mm thick, both conforming to is 513. further fortified by suitable in situ insulating fire resistant barriers to meet the required protection. the overall protection to the contents shall be minimum 70 mm on all six sides. door: the external door of the cabinet shall be of steel of minimum 2 mm thick conforming is 513 and further fortified with hard plate over the lock for burglary protection and in situ insulating fire resistant barrier material to meet required fire protection.  bolt work: the door shall be secured by four way locking mechanism / bolt work with minimum 8 moving shooting bolts of 20 mm diameter. door & body fitment: the door fits in the cabinet having tongue and groove construction that stops hot gases and high temperature to pass through and withstand temperature up to 1010 deg.c. locking: the frrc shall be equipped with a dual control high precision key lock of minimum six levers. the lock body shall be of zinc alloy and the levers in the lock shall be of brass conforming to is 410. there shall not be any dummy lever in the lock. the storage capacity shall be minimum 650 liters with minimum usable internal sizes in mm as 1620 (h) x 670 (w) x 599 (d).the cabinet shall be provided with minimum four nos. adjustable shelves. 20 office chair with seat/back assembly: the cushioned seat assembly consists of seat base moulded in glass filled poly amide, moulded polyurethane foam & upholstered with high stretch knitted polyester fabric. the cushioned back assembly consists of back inner moulded in polypropylene in situ moulded with polyurethane foam & upholstered with high stretch knitted polyester fabric. back size : 45.5 cm. (/1/) x 53.0 cm. (h) seat size : 48.5 cm. (w) x 49.0 cm. (d) high resilience (hr) polyurethane foam: the hr polyurethane foam used in seat and back cushion is moulded in density min 48 kg/m3, and hardness load 15 ± 2 kgf as per is:7888 for 25% compression. tilt mechanism, spines & spine connector: the seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. the cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. the s shaped spines moulded in high strength glass filled poly amide and the spine connector moulded in glass filled poly amide form the back spine structure involved in multi dimensional recline motion. the variable tilt angle recline motion can be adjusted with 3 position tilt limit feature which should be inbuilt in seat base and the tension (return force) should be user weight dependent. adjustable armrests: the assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled poly amide: the height adjustment feature should be button operated having adjustment of 6.6±0.5cm. the armrest top should be made up of integral skin pu moulded over plastic inner moulded in glass filled poly amide. pneumatic height adjustment: the seating height can be adjusted with a pneumatic gas lift having an adjustment stroke of 9.2 ± 0.3 cm pedestal assembly: the pedestal should be injection moulded in glass filled poly amide and fitted with 5 nos. twin wheel castors. the pedestal should be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors twin wheel castors :5 nos. twin wheel castos are injection moulded in poly amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal. 21 hod table of size 1500 x 750 x 743 understructure: the understructure is in prelam panels, made with plt boards.drawer storage units with different combinations to support tops, made with 18mmplt boards of different colours. modesty and back panels, made with 18mm plt boards. the pedestals/storages are fitted with necessary locks plt board tops (straight edges): wenge and savannah maple plt board used for making tops. pvc membrane tops (with profiles): 22 job display board with dimensions (1200x900x150)mm board having 9 mm ply 23 tool display board (1200x900x150)mm board having 9 mm ply 24 chemistry lab table of size 4130mm x 1540mm x 900mm with pp drop sink of size 560 x 355, single tap deck mounted 8 swing goose neck, ss peg board 550x420x55 with 25 pegs. two reagent shelves of width 1050 with glass shelf. c frames all cframes assemblies should be manufactured from standard hollow metal sections; confirming to i.s. code 7138:1973 (indian standard specification for steel tubes for furniture) and all sheet metal components should be of crca confirming to is code 513:1994. the suspended under bench welded units should be supported on heavy duty steel frames fully carrying the load of worktops. c frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. the c frame shall also have skirting at back bottom side. horizontal members should be made from rectangular pipes of 2mm thickness. 25 lab table of size 4130mm x 1540mm x 900mm frames all cframes assemblies should be manufactured from standard hollow metal sections; confirming to i.s. code 7138:1973 (indian standard specification for steel tubes for furniture) and all sheet metal components should be of crca confirming to is code 513:1994. the suspended under bench welded units should be supported on heavy duty steel frames fully carrying the load of worktops. c frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. the c frame shall also have skirting at back bottom side. horizontal members should be made from rectangular pipes of 2mm thickness. cross sectional dimensions of the pipe should be 60 x 30 x 2 mm. 26 locker unit with 4 door plu + lkr (base) with stand size 1830hx380wx450d, stackibilit the add on units can be stacked width wise to formbank of lockers having common side panel, locking cam lock with lock leveroption of hasp arrangement, material crca 0.6mmthickness, rigid knockdown construction, shelf uniformly distributed load capacity per each shelf level is 35 kg maximum, hat self 4 door model at the top, finish epoxy polyester powder coated to the thickness of 50 microns (+/ 10).ventilation attractive punched pattern for ventilation 27 long table of size 1800 x 900 x 740 worktop 25 mm thick plb tops with 2mm thick pvc edge beading understructure c – frames legs 1.6 mm thick m.s c­frame supporting the top. legs dia. 38.1 x 1.6 mm thick m.s erw tube. 28 meeting table with 10 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical/data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309/7558 (black color) 29 notice board with size 4 x 3 surface material woolen felt / fabric in various colours,core material 9 mm thick soft board,backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour or 0.16 to 0.25 mm thick isi mark gp sheet,aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness 30 reception table double arch with dl top of size 2410 x 1065 x 725 worksurface, 1035 counter, d l top top clean matt pu finish 18mm thick inside radius 700.0 mm outside radius – 1350.0 mm depth – 650 mm glass frosted glass 10mm thick diamond cut finishing on edges inside radius – 1202.5mm outside radius – 1402.5mm depth – 200mm, modesty panel ms perforated sheet below worksurface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) above worksurface : 0.8mm (thick) x 260 mm (height) x 1345.0 mm (flat length), legs ms tube 1.6 mm thick diameter 50.8 mm height 604 mm. 31 non magnetic small white board 4 x 3 surface material 0.62 to 0.72 mm thick laminate sheet with extra melamine surface,core material 8 mm thick particle board,backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour,aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness. 32 steel almirah of size 1981 x 916 x 486 mm multi bend construction and inter locking design and full length over apping doors and sides. three way bolting mechanism. spot welding & co2 welding. anticorrosion treated components, oven baked powder coating process. material thickness 0.9mm.top, bottom,lh & rh sides and back material thickness= 0.9mm,removable rh & lh main door with stiffeners material thickness= 0.9mm, 4 adjustable shelves of thickness= 0.8mm 33 steel rack of size 6x36x18 with six shelves prime quality crc sheet conforming to is 513d/10748/5986. the pitches of the slots at 19.05 mm, panel/shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back (minimum) in mm 0.8, paint powder coated with lead free paint. 34 lab stool of circular type 30.0 +/ 0.5 cm and made up of 0.1+/ 0.012 cm thk cr steel. it is welded to the understructure and black powder coated ( dft 40 60 microns ). understructure assembly: the understructure is made of ms tube 2.2 +/ 0.03 cm x 0.16+/ 0.0128 cm thk ms erw tube. lt is welded ti the ms fabricated circular seat assembly and black powder coated ( dft 40 60 microns ). the understructure is provided with black pp injection moulded ferrules. 35 steel rack of size 2 6x36x18 with three shelves prime quality crc sheet conforming to is 513d/10748/5986. the pitches of the slots at 19.05 mm, panel/shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back (minimum) in mm 0.8, paint powder coated with lead free paint. 36 office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side three drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock. 37 computer table of size 600w x 450d x 750h mm compact and easy to use . top made up of 1.5 cm medium density fiber. all the other panels are made of particle board. vacuum lamination of pvc has been done on the table to surface. 0.4mm lapping is used for all the other panels 38 office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18 mm thick pre laminated top size 1365 x 680 x 735 (approx.) with both side drawer unit one side three drawers & another side two drawers made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with both side drawer lock 39 principal table main desk of size 1800 x 900 x 740, eru of size 1550 x 450 x 705 made up of top 25 mm thick plain particle board (ppb) clad with 0.6mm thick post formed laminate and 1mm thick backing laminate (bdl). flat edge duly sealed with 2mm thick pvc beading., modesty 18mm thick plain particle board (ppb) clad with 1.0mm thick decorative laminate (dl) on both sides. edge sealed with 2mm thick pvc beading with 01 no. 3 drawers free standing pedestal. 40 office table with eru & pedestal of size 1350 x 750 x 750 mm + eru + pedestel main desk of size 1350 x 750 x 750 with eru of size 1200 x 450 x 750 & 01 no. 3 drawers pedestal: top panel made from 25 ±0.5 mm thk pre laminated boards as per is 12823 with 2 mm thick pvc beading on all sides. side panel the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm pvc beading on all sides. modestty 1 & 2 the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm thick pvc beading on all edges. the panel is made from 25 ±0.5 mm thk pre laminated boards as per is 12823 with 2 mm thick pvc beading on all sides, the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm pvc beading on all sides. the panel is made from 18 ±0,5 mm thk pre laminated boards as per is 12823 with 0.8 mm thick pvc beading on all edges. pedestal wooden panel ( 1 box+ 1 filling) back wooden panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with pvc beading on all sides. the panel is made from 9 ±0.5 mm thk pre laminated board. 41 steel table with stainless steel top of size 1180 x 750 x 750. worktop the top is in stainless steel brushed finish with plb insert for durability. easy to clean and maintain hygiene. side frames made from 30mm x 30mm x 1.5mm thick m.s powder coated tubes at base which are welded and are fixed to top with screws. the bottom ends are closed with plastic buffers. ms shade : s/g metallic dark grey (nerocoat 9000626), cross member made from 30mm x 30mm x 1.5mm thick m.s powder coated tube, which is welded and bolted to side frames. 42 teaching platform with the dimensions of length 6 ft x breadth 4 ft x height 1.5 ft with 19 mm plywood on top, shall be rectangular hallow box shape without legs. 43 teaching platform with the dimensions of length 12 ft x breadth 6 ft x height 1.5 ft with 19 mm plywood on top, shall be rectangular hallow box shape without legs. 44 wooden podium with dimensions: 45 h x 20 w x 15 d to 50 h x 25 w x 20 dpresenter side height: 40 to 45shelves: 20 h x 20 w x 10 d to 25 h x 25 w x 12 dproduct weight: 50 to 55 lbs.shipping weight: 65 to 70 lbs.material: scratch resistant high pressure laminate.the top of the table shall be provided 19 mm ost. the table shall be neatly finished and polished. 45 seminar chair with understructures could be revolving or fixed type as per need. option of hinge type and retractable desk let.desklet 100% voc free powder coating knock down design reducing transportation emissions designed for long life 46 office table of size 900 x 590 x 750 made of ms erw square tube 18 mm x 25mm x 1.2mm thick with pre laminated top size 1199 x 590 x 750 mm thick with single side one drawers, drawer unit made of .5mm thick ms crca sheet, all steel components have powder coated paint 47 non magnetic long white board 8 x 4 size and surface material 0.62 to 0.72 mm thick laminate sheet with extra melamine surface,core material 8 mm thick particle board,backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour,aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness. 48 double sided book rack with the dimensions width 900mm, height: 1850mm, depth: 600mm, rigid knockdown construction. construction, material crca0.8mmthickness, finish epoxypolyester powder coated to the thickness of 50 microns (+/ 10).number of adjustable shelf: five adjustable shelves on one side (total 12 loading levels). uniformlydistributed load capacity per each shelf is 80 kgmaximum. label holder & range indicator label holder & range indicator on eachmain unit for inserting labels. 49 single sided book rack with the dimensions width 900mm, height: 1850mm, depth: 316mm, rigid knockdown construction, material crca 0.8 mm thickness,finish: epoxypolyester powder coated to the thickness of 50 microns (+/ 10).,number of adjustable shelf five adjustable shelves. (total 6 loading levels). uniformlydistributed load capacity per each shelf is 80 kg maximum, label holder & range indicator label holder & range indicator on eachmain unit for inserting labels. 50 magazine rack with overall dimensions of all steel periodical display rack shall be 900mm(w)x450mm(d)x1830mm(h). rigid knockdown construction ,panels shall be made from crca 0.6 mm thick and front frame shall be made from crca 0.8 mm thick . crca d grade as per is 513 . there shall be 5 level racks , display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . receding facility to access the storage behind . sliding on plastic rollers . behind storage shelving each of 5 level has a behind storage shelf . uniformly distributed load capacity per each shelf is 40 kg . leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns. 51 almirah with glass door size 916mm(w) x 486mm(d) x 1980mm #(h) # excluding leveler, construction & material • welded construction, • 0.7mm thk (±0.07mm) crca* for shelf,• 0.8mm thk (±0.08mm) high yield strength crca** for doors and back,• 0.9mm thk (±0.08mm) crca* for all other components,crca ‘d’ grade as per is:513,crca ‘d’ grade high yield strength as per is:513,locking & handle • brass handle with • two way locking mechanism with shooting bolt, shelves • height wise adjustable shelf mounting • uniformly distributed load capacity per each full shelf is 40 kg maximum, • 4nos. of adjustable full shelf, • box file a4 size (85wx345hx285d) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm,• m10 screw type leveler with hex plastic base,finish • epoxy powder coated to the thickness of 50 microns (+ 10). 52 dual desk is specially designed for rugged use with overall dimentions of l1054 x w980 x h760 mm and all edges are fillet. the desk is made of pressed formed ms crca section & crca tube fitted with pre laminated particle board top, seat & back with injection molded ppcp edge. hanger for water bottle and bag. space for keeping pen, pencil and scale. the overall appearance of the product shall be as per photograph.top injection molded ppcp edge. size : 1054x450x18 mm thk. particle board.seat injection molded ppcp edge. seat height : 450 mm , seat size : 1054x304x18 mm thk. particle board.back injection molded ppcp edge. back size : 1054x154x18 mm thk. particle board.shelf shelf 0.8 mm thk. crca sheet. bullnose front edge with stiffner 1 mm thk crca.modesty modesty 0.8 mm thk. crca sheet. slot perforated.tie members horizontal tie members 25x25x1.2 mm thk. crca pipe.footrest footrest pressed formed crca section 1.5 mm thk. side frame side frame c section pressed formed 1 mm thk.crca sheet welded with 25x50x1.2 mm thk tube. and back rest pipe ø25 x 1.2 mm thk. top end rounded.cap & levellers all pipe caps are curved ppcp material.finish all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. 53 item deleted vide e.n.c. bcd , patna letter no. 6010(bh) anu dated 11.10.2021 54 item deleted vide e.n.c. bcd, patna letter no. 6010(bh) anu dated 11.10.2021 55 dressing table of size 460w x 486d x 1710h mm , mirror w x h: 362 mm x 1156 mm dressing table comes with a long mirror, two storage drawers, and a stool. available in wenge color, the dresser is crafted from good quality mdf wood, making it sturdy and lasting. the shelves of this stylish dressing table can be used to keep items like perfume bottles, hair products, and medicines, for that clutter free look. the stool, also wenge color with an orange colored cushion, offers comfortable seating, while the full length mirror is perfect to dress up, and check your overall ensemble. 56 steel almirah with mirror of size 900w x 507d x 1950h mm rafted from prime steel, your slimline cupboard will be resistant to corrosion and peststhis cupboard comes with 2 easily adjustable shelvesthe hanging rod inside the cupboard ensures ample space for your daily wear, suits, sarees and/or dressesknock down construction makes shifting and handling of slimline easieravailable with over head unit option to maximize vertical space usage you can also choose to have a mirror with slimlinestylish snap shut flush handle enhances slimline’s aesthetics. 57 auditorium chair seat/back assembly: the seat and back are made up of 1.2±0.1 cm. thick hot pressed plywood measured as per qa method described in ocp qlta p14 18 and upholstered with fabric and moulded polyurethane foam. the back is, flexing type.back size 47.0 cm. (w) x 51.0 cm. (h), seat size 47.0 cm. (w) x 47.0 cm. (d). 2. high resilience (hr) polyurethane foam: the hr polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per is:7888 for 25% compression.3. armrests :the one piece armrests are made of black integral skin polyurethane foam with 50 70 shore hardness and reinforced with m.s. insert. the armrests are scratch and weather resistant.5. understructure assembly: it is made of dia. 2.54±0.03cm. x 0.2±0.016cm. thk. m.s.e.r.w. tube with connecting strips made of 0.5 ± 0.05 cm. thk. hr steel welded to it for holding the seat. the assembly is powder coated ( dft 40 60 microns ).the auditorium chair is designed to get mounted/grouted on floors with flooring specification as mentioned in flooring pre requisite godrej doc no: stg 129368.overall width 57.0, depth 57.0, height 86.0, seat height 44.0 cm. 58 movable chair made out of stainless steel, understructure seat and back are made up of injection moulded high impact strength polypropylene polymer compound with indoor grade uv resistance *seat size: 52.5 cm. (w) x 53.2 cm. (d), * back size : 51.6 cm. (w) x 40.5 cm. (h) .s.s. understructure: the tubular welded frame is made from dia 2.22 ± 0.03 cm x o.12 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.12 ± 0.0128 cm stainless steel 202 grade tube. the tubes are buff polished to give shiny finish. 59 hostel bed made out of steel with overall size length 1994mm, width 907mm, height 822/623/ rest height 450mm, structure of metal bed frame including legs and head structure mild steel pipe, head board shape of headboard semi circular, thickness of hollow section in structure (1.2mm), support panel for placement of mattresses mild steel hollow box rectangular section, thickness of support panel (in 1.2mm), material of head board mild steel erw tube is:7138 square tube of 38.1 mm x 1.2 mm thick, material of mattress panel ms perforated / sheet, thickness of mattress panel 1.2 (mm), size of support members in mm (±5 mm) 50 x 50mm, number of support members is 04 nos., paint /finish of all m s parts powder coating 60 micron. 60 dining table of 8 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical/data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309/7558 (black color). 61 item deleted vide e.n.c. bcd, patna letter no. 6010(bh) anu dated 11.10.2021 62 study chair is made of blow molded high density polyethylene andis fixed on the understructure assembly with the help of stainless steel pop rivets.seat: seat is made of blow molded high density polyethylene and is fixed on the understructure assembly.understructure all side metal frames and cross connectors are made from mild steel erw tubes ,40 x 20 x 2mm thk(approx. 14 swg) as per 1s:7138 which are welded togetherthe welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. bag storage tray made of 04 mild steel rod (as per 15:432) forms a cage at the bottom and is welded to the main understructure. seat support channel made of 1mm thk mild steel sheet (as per is:513) is welded to the understructure for fixing seat. plastic caps plastic caps made of polypropylene are provided on the foot rest side tubes and back leg tubes adding more aestheic value to the product. 63 study table with all sides metal frames and cross connectors are made from mild steel erw tubes ,40 x 20 x 2mm thk(approx. 14 swg) as per 15:7138 which are welded together.the welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. shelf tray and desktop mounting brackets made of 2mm thk mild steel sheet(as per 15:513) are welded to the understructure for fixing shelf tray and desktop respectively. hooks are provided ori the vertical side frames on both sides of the desk for hanging bags/bottles. they are made from 09 mild steel rod (as per 15:432) and are welded to the main understructure plastic caps: plastic caps made of polypropylene are provided on the foot rest side tubes and front leg tubes adding more aestheic value to the product. ...

Building Construction Department - Bihar

31163384 supplying and installation furniture for new govt. polytechnic, khagaria 1 1 drawer office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side one drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock. 2 2 seater sofa overall size 1130w x 700d x 785 h cm, seat height 43.5 cm side frame assembly: the side frame assembly is fitted to the two ends of the connecting beam assembly to form, the leg cum armrest assembly. it is made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick ms e.r.w. tube and powder coated ( dft 40 60 microns ) . the ends are fitted with abs moulded end caps, 3. seatrest assembly:the seat rest assembly consists of a fabricated inner frame assembly insitu moulded high resilience ( hr ) polyurethane foam having density = 45 + / 2 kg / m3 with hardness load 25 ± 2 kgf as per is:7888 for 25% compression of the foam. the complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover *seat size: 52.0cm. ( w ) x 50.0cm. ( d ) x 6.0cm. ( t ) , 4. backrest assembly:the backrest assembly is flexing type and consists of a fabricated inner frame assembly insitu moulded with high resilience ( hr ) polyurethane foam having density = 45 +1 2 kg / m3 with hardness load 14 ± 2 kgf as per is:7888 for 25% compression of the foam. the complete moulded backrest assembly is covered with a replaceable fabric upholstery cover. *back size: 52.0cm. ( w ) x 59.0cm. ( h ) x 6.0cm. ( t ) , 5. adj. glides: the adj glide is injection moulded in black nylon & fitted to the front end of side frame assembly along with abs moulded adj. glide base to take care or unleveled floor surface 3 ( 3+1+1 ) seater sofa the side frame assembly made of 38mm dia 2mm thick is fitted to the two ends of the connecting beam assembly to form the leg cum armrest assembly. it is made of a ms. e.r.w. tube duly powder coated. the ends are fitted with abs moulded end caps. tie member: it is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. the tie member is made of ms. e.r.w. tube 40mmx40mm 2mm thick duly powder coated. the seat / back assemblies are mounted on the tie member. l bracket of 6mm thick steel connects the back to the tie member assembly. seat foam is of 45 + / 5 kg / m3 and back foam is of 32 + / 5 kg / m3 with hardness of 25+ / 2 on hampden m / c. at 25% compression of the foam. seat size 52cm widex50cm deep and back size 52 cm wide and 60cm high. back of the sofa flexes for additional comfort 1 seater –601mmwx700mmdx 810mmh, 3 seater –1640w x 700d x 785 h cm 4 3 seater steel chair cross beammade of ms erw rectangular black powder coated tube of 80 x 40 x 2 mm leg & arm rest chrome plated made of cold rolled steel. arm rest & leg assembled to the cross beam with m10 x 100 mm bolts. seat & back 1.6mm thick powder coated perforated shell of cold rolled ms sheet. side bar of chrome plated solid steel 30 x 12 mm ( din 174 ) with flunting & plastic insert .the shell is assembled on the cross beam with help of m8 bolts the overall dimension is 1608mm ( l ) x 695mm ( h ) x 555mm ( d ) , seat height : 405mm 5 bed side locker with one cabinet and one drawer unit . the drawer as well as cabinet is provided with cam lock. there is a gap between the drawer unit and cabinet, to keep the general items for frequent use . castors are provided for easy handling. astainless steel tray is provided at top with raised borders on three sides dimensions ( l ) 402mmx ( w ) 422mmx ( h ) 840mm. drawer has ball slide for easy operation and lock for safety. telescopic ball slides are used for easy and smooth operation of the drawer. plastic moulded castor, 2 castor with lock. recessed handle is provided to open the cabinet door. 6 work bench of size 4’ x 3’, angle 1.5 x 1.5 with 2 pair of legs with work top with overall dimensions. 1200mm l x 900mm d x 950mm h, the worktop of mdf ext garde is12406 wood. max udl 1500kgs the worktop should be made of various layers of beech wood which are planed, glued and pressed together. this should make the work top non deformable, and load and wear resistant. this shall be covered with 4mm steel sheet. leg: the bench leg should be powder coated should be 80mm l x 1265mm d x 960mm h. back bracing for stability 7 centre table of size 1200w x 600d x 378h built with the extremely durable rubberwood, the table can hold weight up to 25kgs. with a very suitable cappuccino color, the table will complement any style of décor. the tapered legs provide stable support. it’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. the well thought out dimensions of the table make it easier to position it anywhere in the house 8 work bench of size 8’ x 4’ with 2 pair of legs with work top with overall dimensions. 2400mm l x 1200mm d x 950mm h, the worktop of mdf ext garde is12406 wood. max udl 1500kgs made of various layers of beech wood which are planed, glued and pressed together. this should make the work top non deformable, and load and wear resistant. bench leg: the bench leg should be powder coated should be 80mm l x 1265mm d x 960mm h. back bracing for stability 9 executive chair with cushioned seat is made of injection molded plastic outer & inner. plastic inner is upholstered with stitched cover and moulded high resilience polyurethane foam of density 4542 kg / m*, and hardness load 16 + 2 kgf as per 15:7888 for 25% compression.the stitched cover is made from spacer fabric and leatherette seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) , tunular frame : the powder coated ( dft 40 60 micron ) tubular frame is cantilever type & made of 02.5440.03 cm x 0.240.016 cm thk ms erw tube.the back connected to frame through powder coated ( dft 40 60 micron ) high pressure die cast connector. 10 office chair with seat and back are made from seasoned wood and plywood. the same is upholstered with black synthetic leather and polyurethane foam. back size 46.0cm ( w ) x27.0cm ( h ) . seat size 46.0cm ( w ) x40.0cm ( h ) . the armrest is gas assisted injection moulded from black polypropylene. the understructure assembly is a cantilever type frame.width of the chair 58cm, depth 56.5cm, height 87.5cm, seat height 48cm. 11 office chair : the seat and back are made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per qa method described in ocp qlta p14 18 and upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the back foam is designed with contoured lumbar support for extra comfort. back size 49.0 cm. ( w ) x 47.0 cm. ( h ) , seat size 49.0 cm. ( w ) x 44.0 cm. ( id ) high resilience ( hr ) polyurethane foam: the hr polyurethane foam is moulded with density = 45 ±2 kg / m3 and hardness load 16 ± 2 kgf as per is:7888 for 25% compression. 12 principal chair: the seat is made up of 1.4± 0.1 chick hot press 4 plywood upholstered with fabric and moulded polyurethane foam. it has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. seat size: 50.0cm ( w ) x 49.0cm ( d ) .the back is injection moulded in glass filled polyamide which is upholstered with mesh fabric. the back consist of adjustable lumbar support made of injection moulded polypropylene having an adjustment of 6.0±0.1cm.backsize: 50.0cm ( w ) x68.0 cm ( h ) .the polyurethane foam for seat is of density 55± 5kg / m3. it is made of glass filled polyamide arm structure with pu arm top and height adjustment of 7.0 ±0.5cm.the arm top has swivel and to for movements. to for movement is 6.0± 0.5cm.the inner tube of armrest is chrome plated. the mechanism is designed with the following features:• 360° revolving type.• centre tilt synchro• 3 position ( including upright lock ) giving option of variable tilt angle to the chair with anti shock feature. the headrest is injection moulded din glass filled polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the full back chair. the pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.the pedestal is high pressure die cast polished aluminum and fitted with 5 nos. twin wheel castors. the pedestal is 65.0±0.5 cm p.c.d. the twin wheel castors are injection moulded in black glass filled polyamide having 6.0±0.1cm wheel diameter. the chrome plated tubular frame is made of día2.8±0.03cm x0.2±0.02 cm the m.s. round tube. the frame is fitted with plastic caps made of injection moulded glass filled polypropylene. 75 ( w ) * 75 ( d ) * 115 130 ( h ) * 44.5 53.5 ( sh ) . 13 computer chair with seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade uv resistance.the tubular weled frame is made from dia2.22 + / 0.03cmx 0.12+ / 0.0128 cm and 3.5+ / 0.03 cm x 0.12+ / 0.0128 am stainless steel 202 grade tube.the tube are buff polished to give shiny finish. cm. the shoes are made of high impact strenght polypropylene polymer. compond with indoor grad uv resistance and pressed fitted with tubularfram. size : ( w ) 52.5cm* ( d ) 55.8cm* ( h ) 84.5cm* ( seat h ) 45.0 cmseat size 52.5cm ( w ) *53.2 cm ( d ) back size 51.6 cm ( w ) *40.5 cm ( h ) . 14 office chair mid back pneumatic height adjustment cushioned revolving chair made up of 1.2cm thick hot pressed ply wood seat & back upholstered with fabric with moulded polyurethane foam together with moulded abs seat & back integral skin polyurethane with reinforced with m.s. insert. the tilt mechanism adjustment upright locking, 360 degree revolving type fitted with 05 nos. twin wheel castor dia 5 cm. 15 compactor on 12 feet rail length moves on rails. the cabinet body rigid knock down construction made of 0.8 thick crca steel eonforming to is: 513 gld. body units are bolted to undercarriage. optimizer height from ground is 2081 ] mm ( 1930 hody+ 65 under 35 channel systems ] finish: — the bodies inciuding shelves are given anti rust surface treatment 8‘ are powder coated with epoxy polyester powder oven backed with a controlled temperature of 130 deg. to 200 deg. c.sheif:l made of 0.8 thick crca steel conforming to is;513 gd. max load bearing capacin is fit! kg. udl per ahett x 5:400 kg. eauh cabinet. undercarriage: the undercarriage is a welded trams made of hr sheet 3.15 mm thick conforming [ 0 is; 1d?48movement of the system: push pull configuration { type p utype f~2 } movement of units achieved pushing or putting chrome plated 0 handle fitted suitable height on one side at body. 16 conference table of 30 seater capacity shall be an eco modular conference table enables various configurations to suit different conference rooms. it is made of particle board and has wire management facilities for uncluttered wiring. it has profiled legs with twin colored modesty for better looks, double 1350.0wx 600.0dx 750.0h, work surface top thickness is 25mm plb with pvc beading allover, legs modesty wire manager made from 18mm thick plt having curved profile.made from plt ( prelaminated twin ) boards 18mm thick in two shades. a wire manager running along the width of desk fitted on the modesty panel from inside. 17 corner table of size 530w x 450d x 450h built with the extremely durable rubberwood, with a very suitable cappuccino color, the table will complement any style of décor. the tapered legs provide stable support. it’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. the well thought out dimensions of the table make it easier to position it anywhere in the house. 18 dining table of 8 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical / data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309 / 7558 ( black color ) . 19 file cabinet with 4 drawer width: 470mm, height: 1320mm, depth: 620mm , rigid knockdown construction, material: top, side & drawer frontmade from0.7mm thk **crca, drawer inside cover, side back side made from0.6mmthk **crca, back, bottom, drawer bottommade from 0.5mmthk **crca, **crcasteel confirming to is 513, grade d, label holder snap on type plastic label holder on drawer fronts, locking & anti tipping arrangement centralized lockingwith camlock& having antitipping arrangement to ensure that when one , drawer is opened for use, it does not allow other drawers to be opened, finish epoxy polyester powder coated to the thickness of 50 microns ( + / 10 ) . 20 fire proof cabinet shall be designed to protect the contents ( paper media documents ) against the fire hazard.shell: the external shell of the cabinet shall be of steel of minimum 2 mm thick and internal shell of steel of 1.6 mm thick, both conforming to is 513. further fortified by suitable in situ insulating fire resistant barriers to meet the required protection. the overall protection to the contents shall be minimum 70 mm on all six sides. door: the external door of the cabinet shall be of steel of minimum 2 mm thick conforming is 513 and further fortified with hard plate over the lock for burglary protection and in situ insulating fire resistant barrier material to meet required fire protection.  bolt work: the door shall be secured by four way locking mechanism / bolt work with minimum 8 moving shooting bolts of 20 mm diameter. door & body fitment: the door fits in the cabinet having tongue and groove construction that stops hot gases and high temperature to pass through and withstand temperature up to 1010 deg.c. locking: the frrc shall be equipped with a dual control high precision key lock of minimum six levers. the lock body shall be of zinc alloy and the levers in the lock shall be of brass conforming to is 410. there shall not be any dummy lever in the lock. the storage capacity shall be minimum 650 liters with minimum usable internal sizes in mm as 1620 ( h ) x 670 ( w ) x 599 ( d ) .the cabinet shall be provided with minimum four nos. adjustable shelves. 21 office chair with seat / back assembly: the cushioned seat assembly consists of seat base moulded in glass filled poly amide, moulded polyurethane foam & upholstered with high stretch knitted polyester fabric. the cushioned back assembly consists of back inner moulded in polypropylene in situ moulded with polyurethane foam & upholstered with high stretch knitted polyester fabric. back size : 45.5 cm. ( / 1 / ) x 53.0 cm. ( h ) seat size : 48.5 cm. ( w ) x 49.0 cm. ( d ) high resilience ( hr ) polyurethane foam: the hr polyurethane foam used in seat and back cushion is moulded in density min 48 kg / m3, and hardness load 15 ± 2 kgf as per is:7888 for 25% compression. tilt mechanism, spines & spine connector: the seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. the cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. the s shaped spines moulded in high strength glass filled poly amide and the spine connector moulded in glass filled poly amide form the back spine structure involved in multi dimensional recline motion. the variable tilt angle recline motion can be adjusted with 3 position tilt limit feature which should be inbuilt in seat base and the tension ( return force ) should be user weight dependent. adjustable armrests: the assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled poly amide: the height adjustment feature should be button operated having adjustment of 6.6±0.5cm. the armrest top should be made up of integral skin pu moulded over plastic inner moulded in glass filled poly amide. pneumatic height adjustment: the seating height can be adjusted with a pneumatic gas lift having an adjustment stroke of 9.2 ± 0.3 cm pedestal assembly: the pedestal should be injection moulded in glass filled poly amide and fitted with 5 nos. twin wheel castors. the pedestal should be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors twin wheel castors :5 nos. twin wheel castos are injection moulded in poly amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal. 22 hod table of size 1500 x 750 x 743 understructure: the understructure is in prelam panels, made with plt boards.drawer storage units with different combinations to support tops, made with 18mmplt boards of different colours. modesty and back panels, made with 18mm plt boards. the pedestals / storages are fitted with necessary locks plt board tops ( straight edges ) : wenge and savannah maple plt board used for making tops. pvc membrane tops ( with profiles ) : 23 job display board with dimensions ( 1200x900x150 ) mm board having 9 mm ply 24 tool display board ( 1200x900x150 ) mm board having 9 mm ply 25 chemistry lab table of size 4130mm x 1540mm x 900mm with pp drop sink of size 560 x 355, single tap deck mounted 8 swing goose neck, ss peg board 550x420x55 with 25 pegs. two reagent shelves of width 1050 with glass shelf. c frames all cframes assemblies should be manufactured from standard hollow metal sections; confirming to i.s. code 7138:1973 ( indian standard specification for steel tubes for furniture ) and all sheet metal components should be of crca confirming to is code 513:1994. the suspended under bench welded units should be supported on heavy duty steel frames fully carrying the load of worktops. c frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. the c frame shall also have skirting at back bottom side. horizontal members should be made from rectangular pipes of 2mm thickness. 26 lab table of size 4130mm x 1540mm x 900mm frames all cframes assemblies should be manufactured from standard hollow metal sections; confirming to i.s. code 7138:1973 ( indian standard specification for steel tubes for furniture ) and all sheet metal components should be of crca confirming to is code 513:1994. the suspended under bench welded units should be supported on heavy duty steel frames fully carrying the load of worktops. c frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. the c frame shall also have skirting at back bottom side. horizontal members should be made from rectangular pipes of 2mm thickness. cross sectional dimensions of the pipe should be 60 x 30 x 2 mm. 27 locker unit with 4 door plu + lkr ( base ) with stand size 1830hx380wx450d, stackibilit the add on units can be stacked width wise to formbank of lockers having common side panel, locking cam lock with lock leveroption of hasp arrangement, material crca 0.6mmthickness, rigid knockdown construction, shelf uniformly distributed load capacity per each shelf level is 35 kg maximum, hat self 4 door model at the top, finish epoxy polyester powder coated to the thickness of 50 microns ( + / 10 ) .ventilation attractive punched pattern for ventilation 28 long table of size 1800 x 900 x 740 worktop 25 mm thick plb tops with 2mm thick pvc edge beading understructure c – frames legs 1.6 mm thick m.s c­frame supporting the top. legs dia. 38.1 x 1.6 mm thick m.s erw tube. 29 bed mattress of size ( l ) 1900 x ( w ) 900 x ( h ) 100 mm providing and supplying sheet bed mattress 100mm the bed should be provided with 40 density 100mm thick single section pu from mattress which should be covered with heavy helium material is water proof , flame retardent vapour and x ray permeablee.the zip and stiches for the mattress cover should be concealed.the manufacturer should be compliant with iso 9001 , 14001, 13485 and ohsas 1800 and ce certification. the work shall be carried as per instruction of engineer in charge. 30 meeting table with 10 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical / data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309 / 7558 ( black color ) 31 notice board with size 4 x 3 surface material woolen felt / fabric in various colours, core material 9 mm thick soft board, backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour or 0.16 to 0.25 mm thick isi mark gp sheet, aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness 32 magazine rack with overall dimensions of all steel periodical display rack shall be 900mm ( w ) x450mm ( d ) x1830mm ( h ) . rigid knockdown construction , panels shall be made from crca 0.6 mm thick and front frame shall be made from crca 0.8 mm thick . crca d grade as per is 513 . there shall be 5 level racks , display tray shall be suitable for fullscape size magazines, periodicals, aesthetically appealing metal tray at an angle for easy viewing . receding facility to access the storage behind . sliding on plastic rollers . behind storage shelving each of 5 level has a behind storage shelf . uniformly distributed load capacity per each shelf is 40 kg . leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns. 33 patient bed with overall size ( l ) 2106mm x ( w ) 914mm x ( h ) 614mm , head board / leg board frame ms erw round tube thickness 1.6mm , lying surface 1.0mm crca sheet leg shoe neoprene rubber with reinforced metal washer for avoiding wear of legs. mosquito net pole holder provision for mounting of mosquito net pole, iv pole holder provision for mounting of iv pole , powder coating anti rust thermosetting epoxy polyster , formulated to fulfill the requirement for surface protection maximum patient load 135 kg . 34 reception table double arch with dl top of size 2410 x 1065 x 725 worksurface, 1035 counter, d l top top clean matt pu finish 18mm thick inside radius 700.0 mm outside radius – 1350.0 mm depth – 650 mm glass frosted glass 10mm thick diamond cut finishing on edges inside radius – 1202.5mm outside radius – 1402.5mm depth – 200mm, modesty panel ms perforated sheet below worksurface : 0.8 mm ( thick ) x 665.0 mm ( height ) x 1345.0 mm ( flat length ) above worksurface : 0.8mm ( thick ) x 260 mm ( height ) x 1345.0 mm ( flat length ) , legs ms tube 1.6 mm thick diameter 50.8 mm height 604 mm. 35 non magnetic small white board 4 x 3 surface material 0.62 to 0.72 mm thick laminate sheet with extra melamine surface, core material 8 mm thick particle board, backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour, aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness. 36 steel top stool overall dimension: overall size diagonal sizes diagonal leg dia. 538mm ( h ) 470min 655max . top plate should made of ss202 made sheet with spin section of thickness 1mm and should non corresive. it should have a diameter of 350mm seat base should made of ms ring and rectangular tube. en8 screw having dia of 22mm should be used for height adjustment of the seat base .the round hub should be made of ms erw tube haiving dia of 38mm and thickness 2mm . the hub should be welded with the legs and it should accommodated and cover the lid screw mechanism. the understructure should consist of 4 legs made up of ms erw tube of dia 25.4mm and 1.6mm thick. the press formed pipe leg should give a round and clean lock. the legs should be provided with 4 nos of nylon 6 bush. all metal components should be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbial epoxy polyster powder coating to fulfill the requirements bactarial protection against at last 2 commnly found bactaria in hospital environment ( gram positive and gram negative ) . safe working load must be 135 kg. 37 steel almirah of size 1981 x 916 x 486 mm multi bend construction and inter locking design and full length over apping doors and sides. three way bolting mechanism. spot welding & co2 welding. anticorrosion treated components, oven baked powder coating process. material thickness 0.9mm.top, bottom, lh & rh sides and back material thickness= 0.9mm, removable rh & lh main door with stiffeners material thickness= 0.9mm, 4 adjustable shelves of thickness= 0.8mm 38 steel rack of size 6x36x18 with six shelves prime quality crc sheet conforming to is 513d / 10748 / 5986. the pitches of the slots at 19.05 mm, panel / shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back ( minimum ) in mm 0.8, paint powder coated with lead free paint. 39 lab stool of circular type 30.0 + / 0.5 cm and made up of 0.1+ / 0.012 cm thk cr steel. it is welded to the understructure and black powder coated ( dft 40 60 microns ) . understructure assembly: the understructure is made of ms tube 2.2 + / 0.03 cm x 0.16+ / 0.0128 cm thk ms erw tube. lt is welded ti the ms fabricated circular seat assembly and black powder coated ( dft 40 60 microns ) . the understructure is provided with black pp injection moulded ferrules. 40 steel rack of size 2 6x36x18 with three shelves prime quality crc sheet conforming to is 513d / 10748 / 5986. the pitches of the slots at 19.05 mm, panel / shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back ( minimum ) in mm 0.8, paint powder coated with lead free paint. 41 office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side three drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock. 42 computer table of size 600w x 450d x 750h mm compact and easy to use . top made up of 1.5 cm medium density fiber. all the other panels are made of particle board. vacuum lamination of pvc has been done on the table to surface. 0.4mm lapping is used for all the other panels 43 office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18 mm thick pre laminated top size 1365 x 680 x 735 ( approx. ) with both side drawer unit one side three drawers & another side two drawers made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with both side drawer lock 44 principal table main desk of size 1800 x 900 x 740, eru of size 1550 x 450 x 705 made up of top 25 mm thick plain particle board ( ppb ) clad with 0.6mm thick post formed laminate and 1mm thick backing laminate ( bdl ) . flat edge duly sealed with 2mm thick pvc beading., modesty 18mm thick plain particle board ( ppb ) clad with 1.0mm thick decorative laminate ( dl ) on both sides. edge sealed with 2mm thick pvc beading with 01 no. 3 drawers free standing pedestal. 45 office table with eru & pedestal of size 1350 x 750 x 750 mm + eru + pedestel main desk of size 1350 x 750 x 750 with eru of size 1200 x 450 x 750 & 01 no. 3 drawers pedestal: top panel made from 25 ±0.5 mm thk pre laminated boards as per is 12823 with 2 mm thick pvc beading on all sides. side panel the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm pvc beading on all sides. modestty 1 & 2 the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm thick pvc beading on all edges. the panel is made from 25 ±0.5 mm thk pre laminated boards as per is 12823 with 2 mm thick pvc beading on all sides, the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm pvc beading on all sides. the panel is made from 18 ±0, 5 mm thk pre laminated boards as per is 12823 with 0.8 mm thick pvc beading on all edges. pedestal wooden panel ( 1 box+ 1 filling ) back wooden panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with pvc beading on all sides. the panel is made from 9 ±0.5 mm thk pre laminated board. 46 steel table with stainless steel top of size 1180 x 750 x 750. worktop the top is in stainless steel brushed finish with plb insert for durability. easy to clean and maintain hygiene. side frames made from 30mm x 30mm x 1.5mm thick m.s powder coated tubes at base which are welded and are fixed to top with screws. the bottom ends are closed with plastic buffers. ms shade : s / g metallic dark grey ( nerocoat 9000626 ) , cross member made from 30mm x 30mm x 1.5mm thick m.s powder coated tube, which is welded and bolted to side frames. 47 teaching platform with the dimensions of length 6 ft x breadth 4 ft x height 1.5 ft with 19 mm plywood on top, shall be rectangular hallow box shape without legs. 48 teaching platform with the dimensions of length 12 ft x breadth 6 ft x height 1.5 ft with 19 mm plywood on top, shall be rectangular hallow box shape without legs. 49 wooden podium with dimensions: 45 h x 20 w x 15 d to 50 h x 25 w x 20 d presenter side height: 40 to 45 shelves: 20 h x 20 w x 10 d to 25 h x 25 w x 12 d product weight: 50 to 55 lbs. shipping weight: 65 to 70 lbs. material: scratch resistant high pressure laminate. the top of the table shall be provided 19 mm ost. the table shall be neatly finished and polished. 50 seminar chair with understructures could be revolving or fixed type as per need. option of hinge type and retractable desk let. desklet 100% voc free powder coating knock down design reducing transportation emissions designed for long life 51 office table of size 900 x 590 x 750 made of ms erw square tube 18 mm x 25mm x 1.2mm thick with pre laminated top size 1199 x 590 x 750 mm thick with single side one drawers, drawer unit made of .5mm thick ms crca sheet, all steel components have powder coated paint 52 non magnetic long white board 8 x 4 size and surface material 0.62 to 0.72 mm thick laminate sheet with extra melamine surface, core material 8 mm thick particle board, backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour, aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness. 53 double sided book rack with the dimensions width 900mm, height: 1850mm, depth: 600mm, rigid knockdown construction. construction, material crca0.8mmthickness, finish epoxypolyester powder coated to the thickness of 50 microns ( + / 10 ) .number of adjustable shelf: five adjustable shelves on one side ( total 12 loading levels ) . uniformlydistributed load capacity per each shelf is 80 kgmaximum. label holder & range indicator label holder & range indicator on eachmain unit for inserting labels. 54 single sided book rack with the dimensions width 900mm, height: 1850mm, depth: 316mm, rigid knockdown construction, material crca 0.8 mm thickness, finish: epoxypolyester powder coated to the thickness of 50 microns ( + / 10 ) ., number of adjustable shelf five adjustable shelves. ( total 6 loading levels ) . uniformlydistributed load capacity per each shelf is 80 kg maximum, label holder & range indicator label holder & range indicator on eachmain unit for inserting labels. 55 almirah with glass door size 916mm ( w ) x 486mm ( d ) x 1980mm # ( h ) # excluding leveler, construction & material • welded construction, • 0.7mm thk ( ±0.07mm ) crca* for shelf, • 0.8mm thk ( ±0.08mm ) high yield strength crca** for doors and back, • 0.9mm thk ( ±0.08mm ) crca* for all other components, crca ‘d’ grade as per is:513, crca ‘d’ grade high yield strength as per is:513, locking & handle • brass handle with • two way locking mechanism with shooting bolt, shelves • height wise adjustable shelf mounting • uniformly distributed load capacity per each full shelf is 40 kg maximum, • 4nos. of adjustable full shelf, • box file a4 size ( 85wx345hx285d ) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm, • m10 screw type leveler with hex plastic base, finish • epoxy powder coated to the thickness of 50 microns ( + 10 ) . 56 dual desk is specially designed for rugged use with overall dimentions of l1054 x w980 x h760 mm and all edges are fillet. the desk is made of pressed formed ms crca section & crca tube fitted with pre laminated particle board top, seat & back with injection molded ppcp edge. hanger for water bottle and bag. space for keeping pen, pencil and scale. the overall appearance of the product shall be as per photograph. top injection molded ppcp edge. size : 1054x450x18 mm thk. particle board. seat injection molded ppcp edge. seat height : 450 mm , seat size : 1054x304x18 mm thk. particle board. back injection molded ppcp edge. back size : 1054x154x18 mm thk. particle board. shelf shelf 0.8 mm thk. crca sheet. bullnose front edge with stiffner 1 mm thk crca. modesty modesty 0.8 mm thk. crca sheet. slot perforated. tie members horizontal tie members 25x25x1.2 mm thk. crca pipe. footrest footrest pressed formed crca section 1.5 mm thk. side frame side frame c section pressed formed 1 mm thk.crca sheet welded with 25x50x1.2 mm thk tube. and back rest pipe ø25 x 1.2 mm thk. top end rounded. cap & levellers all pipe caps are curved ppcp material. finish all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. 57 item deleted vide e.n.c bcd, patna letter no 6010 ( bh ) anu dated 11.10.2021 58 item deleted vide e.n.c bcd, patna letter no 6010 ( bh ) anu dated 11.10.2021 59 hostel bed made out of steel with overall size length 1994mm, width 907mm, height 822 / 623 / rest height 450mm, structure of metal bed frame including legs and head structure mild steel pipe, head board shape of headboard semi circular, thickness of hollow section in structure ( 1.2mm ) , support panel for placement of mattresses mild steel hollow box rectangular section, thickness of support panel ( in 1.2mm ) , material of head board mild steel erw tube is:7138 square tube of 38.1 mm x 1.2 mm thick, material of mattress panel ms perforated / sheet, thickness of mattress panel 1.2 ( mm ) , size of support members in mm ( ±5 mm ) 50 x 50mm, number of support members is 04 nos., paint / finish of all m s parts powder coating 60 micron. 60 dining table of 8 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical / data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309 / 7558 ( black color ) . 61 item deleted vide e.n.c bcd, patna letter no 6010 ( bh ) anu dated 11.10.2021 62 study chair is made of blow molded high density polyethylene andis fixed on the understructure assembly with the help of stainless steel pop rivets.seat: seat is made of blow molded high density polyethylene and is fixed on the understructure assembly.understructure all side metal frames and cross connectors are made from mild steel erw tubes , 40 x 20 x 2mm thk ( approx. 14 swg ) as per 1s:7138 which are welded togetherthe welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. bag storage tray made of 04 mild steel rod ( as per 15:432 ) forms a cage at the bottom and is welded to the main understructure. seat support channel made of 1mm thk mild steel sheet ( as per is:513 ) is welded to the understructure for fixing seat. plastic caps plastic caps made of polypropylene are provided on the foot rest side tubes and back leg tubes adding more aestheic value to the product. 63 steel rack of size 6x36x18 with six shelves prime quality crc sheet conforming to is 513d / 10748 / 5986. the pitches of the slots at 19.05 mm, panel / shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back ( minimum ) in mm 0.8, paint powder coated with lead free paint. 64 study table with all sides metal frames and cross connectors are made from mild steel erw tubes , 40 x 20 x 2mm thk ( approx. 14 swg ) as per 15:7138 which are welded together.the welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. shelf tray and desktop mounting brackets made of 2mm thk mild steel sheet ( as per 15:513 ) are welded to the understructure for fixing shelf tray and desktop respectively. hooks are provided ori the vertical side frames on both sides of the desk for hanging bags / bottles. they are made from 09 mild steel rod ( as per 15:432 ) and are welded to the main understructure plastic caps: plastic caps made of polypropylene are provided on the foot rest side tubes and front leg tubes adding more aestheic value to the product. 65 office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side one drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock....

Building Construction Department - Bihar

31015414 supply of furniture and other items for govt. engineering college, arwal. ot d office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side one drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock. 2ss 2 seater sofa overall size 1130w x 700d x 785 h cm, seat height 43.5 cm side frame assembly: the side frame assembly is fitted to the two ends of the connecting beam assembly to form, the leg cum armrest assembly. it is made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick ms e.r.w. tube and powder coated ( dft 40 60 microns ) . the ends are fitted with abs moulded end caps, 3. seatrest assembly:the seat rest assembly consists of a fabricated inner frame assembly insitu moulded high resilience ( hr ) polyurethane foam having density = 45 + / 2 kg / m3 with hardness load 25 ± 2 kgf as per is:7888 for 25% compression of the foam. the complete moulded seat rest assembly is covered with a replaceable fabric upholstery cover *seat size: 52.0cm. ( w ) x 50.0cm. ( d ) x 6.0cm. ( t ) , 4. backrest assembly:the backrest assembly is flexing type and consists of a fabricated inner frame assembly insitu moulded with high resilience ( hr ) polyurethane foam having density = 45 +1 2 kg / m3 with hardness load 14 ± 2 kgf as per is:7888 for 25% compression of the foam. the complete moulded backrest assembly is covered with a replaceable fabric upholstery cover. *back size: 52.0cm. ( w ) x 59.0cm. ( h ) x 6.0cm. ( t ) , 5. adj. glides: the adj glide is injection moulded in black nylon & fitted to the front end of side frame assembly along with abs moulded adj. glide base to take care or unleveled floor surface 3ss 3 seater sofa the side frame assembly made of 38mm dia 2mm thick is fitted to the two ends of the connecting beam assembly to form the leg cum armrest assembly. it is made of a ms. e.r.w. tube duly powder coated. the ends are fitted with abs moulded end caps. tie member: it is the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members are used to connect the side frames. the tie member is made of ms. e.r.w. tube 40mmx40mm 2mm thick duly powder coated. the seat / back assemblies are mounted on the tie member. l bracket of 6mm thick steel connects the back to the tie member assembly. seat foam is of 45 + / 5 kg / m3 and back foam is of 32 + / 5 kg / m3 with hardness of 25+ / 2 on hampden m / c. at 25% compression of the foam. seat size 52cm widex50cm deep and back size 52 cm wide and 60cm high. back of the sofa flexes for additional comfort 1 seater –601mmwx700mmdx 810mmh, 3 seater –1640w x 700d x 785 h cm 3s wc 3 seater steel chair cross beammade of ms erw rectangular black powder coated tube of 80 x 40 x 2 mm leg & arm rest chrome plated made of cold rolled steel. arm rest & leg assembled to the cross beam with m10 x 100 mm bolts. seat & back 1.6mm thick powder coated perforated shell of cold rolled ms sheet. side bar of chrome plated solid steel 30 x 12 mm ( din 174 ) with flunting & plastic insert .the shell is assembled on the cross beam with help of m8 bolts the overall dimension is 1608mm ( l ) x 695mm ( h ) x 555mm ( d ) , seat height : 405mm wb a work bench of size 4’ x 3’, angle 1.5 x 1.5 with 2 pair of legs with work top with overall dimensions. 1200mm l x 900mm d x 950mm h, the worktop of mdf ext garde is12406 wood. max udl 1500kgs the worktop should be made of various layers of beech wood which are planed, glued and pressed together. this should make the work top non deformable, and load and wear resistant. this shall be covered with 4mm steel sheet. leg: the bench leg should be powder coated should be 80mm l x 1265mm d x 960mm h. back bracing for stability cnt centre table of size 1200w x 600d x 378h built with the extremely durable rubberwood, the table can hold weight up to 25kgs. with a very suitable cappuccino color, the table will complement any style of décor. the tapered legs provide stable support. it’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. the well thought out dimensions of the table make it easier to position it anywhere in the house wb b work bench of size 8’ x 4’ with 2 pair of legs with work top with overall dimensions. 2400mm l x 1200mm d x 950mm h, the worktop of mdf ext garde is12406 wood. max udl 1500kgs made of various layers of beech wood which are planed, glued and pressed together. this should make the work top non deformable, and load and wear resistant. bench leg: the bench leg should be powder coated should be 80mm l x 1265mm d x 960mm h. back bracing for stability ec cu executive chair with cushioned seat is made of injection molded plastic outer & inner. plastic inner is upholstered with stitched cover and moulded high resilience polyurethane foam of density 4542 kg / m*, and hardness load 16 + 2 kgf as per 15:7888 for 25% compression.the stitched cover is made from spacer fabric and leatherette seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) , tunular frame : the powder coated ( dft 40 60 micron ) tubular frame is cantilever type & made of 02.5440.03 cm x 0.240.016 cm thk ms erw tube.the back connected to frame through powder coated ( dft 40 60 micron ) high pressure die cast connector. oc a office chair with seat and back are made from seasoned wood and plywood. the same is upholstered with black synthetic leather and polyurethane foam. back size 46.0cm ( w ) x27.0cm ( h ) . seat size 46.0cm ( w ) x40.0cm ( h ) . the armrest is gas assisted injection moulded from black polypropylene. the understructure assembly is a cantilever type frame.width of the chair 58cm, depth 56.5cm, height 87.5cm, seat height 48cm. oc b office chair : the seat and back are made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per qa method described in ocp qlta p14 18 and upholstered with fabric and moulded polyurethane foam with pvc lipping all around. the back foam is designed with contoured lumbar support for extra comfort. back size 49.0 cm. ( w ) x 47.0 cm. ( h ) , seat size 49.0 cm. ( w ) x 44.0 cm. ( id ) high resilience ( hr ) polyurethane foam: the hr polyurethane foam is moulded with density = 45 ±2 kg / m3 and hardness load 16 ± 2 kgf as per is:7888 for 25% compression. pc principal chair: the seat is made up of 1.4± 0.1 chick hot press 4 plywood upholstered with fabric and moulded polyurethane foam. it has a seat depth adjustment of 5.0±0.3 cm integrated in the seat through a sliding mechanism. seat size: 50.0cm ( w ) x 49.0cm ( d ) .the back is injection moulded in glass filled polyamide which is upholstered with mesh fabric. the back consist of adjustable lumbar support made of injection moulded polypropylene having an adjustment of 6.0±0.1cm.backsize: 50.0cm ( w ) x68.0 cm ( h ) .the polyurethane foam for seat is of density 55± 5kg / m3. it is made of glass filled polyamide arm structure with pu arm top and height adjustment of 7.0 ±0.5cm.the arm top has swivel and to for movements. to for movement is 6.0± 0.5cm.the inner tube of armrest is chrome plated. the mechanism is designed with the following features:• 360° revolving type.• centre tilt synchro• 3 position ( including upright lock ) giving option of variable tilt angle to the chair with anti shock feature. the headrest is injection moulded din glass filled polypropylene which is upholstered with foam and fabric has an adjustment of 6.0± 0.1cm & its assembled over the full back chair. the pneumatic height adjustment is chrome plated with an adjustment stroke of 9.0 ± 0.3cm.the pedestal is high pressure die cast polished aluminum and fitted with 5 nos. twin wheel castors. the pedestal is 65.0±0.5 cm p.c.d. the twin wheel castors are injection moulded in black glass filled polyamide having 6.0±0.1cm wheel diameter. the chrome plated tubular frame is made of día2.8±0.03cm x0.2±0.02 cm the m.s. round tube. the frame is fitted with plastic caps made of injection moulded glass filled polypropylene. 75 ( w ) * 75 ( d ) * 115 130 ( h ) * 44.5 53.5 ( sh ) . cc wa computer chair with seat and back are made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade uv resistance.the tubular weled frame is made from dia2.22 + / 0.03cmx 0.12+ / 0.0128 cm and 3.5+ / 0.03 cm x 0.12+ / 0.0128 am stainless steel 202 grade tube.the tube are buff polished to give shiny finish. cm. the shoes are made of high impact strenght polypropylene polymer. compond with indoor grad uv resistance and pressed fitted with tubularfram. size : ( w ) 52.5cm* ( d ) 55.8cm* ( h ) 84.5cm* ( seat h ) 45.0 cmseat size 52.5cm ( w ) *53.2 cm ( d ) back size 51.6 cm ( w ) *40.5 cm ( h ) . oc c office chair mid back pneumatic height adjustment cushioned revolving chair made up of 1.2cm thick hot pressed ply wood seat & back upholstered with fabric with moulded polyurethane foam together with moulded abs seat & back integral skin polyurethane with reinforced with m.s. insert. the tilt mechanism adjustment upright locking, 360 degree revolving type fitted with 05 nos. twin wheel castor dia 5 cm. comr compactor on 12 feet rail length moves on rails. the cabinet body rigid knock down construction made of 0.8 thick crca steel eonforming to is: 513 gld. body units are bolted to undercarriage. optimizer height from ground is 2081 ] mm ( 1930 hody+ 65 under 35 channel systems ] finish: — the bodies inciuding shelves are given anti rust surface treatment 8‘ are powder coated with epoxy polyester powder oven backed with a controlled temperature of 130 deg. to 200 deg. c.sheif:l made of 0.8 thick crca steel conforming to is;513 gd. max load bearing capacin is fit! kg. udl per ahett x 5:400 kg. eauh cabinet. undercarriage: the undercarriage is a welded trams made of hr sheet 3.15 mm thick conforming [ 0 is; 1d?48movement of the system: push pull configuration { type p utype f~2 } movement of units achieved pushing or putting chrome plated 0 handle fitted suitable height on one side at body. cnft conference table of 30 seater capacity shall be an eco modular conference table enables various configurations to suit different conference rooms. it is made of particle board and has wire management facilities for uncluttered wiring. it has profiled legs with twin colored modesty for better looks, double 1350.0wx 600.0dx 750.0h, work surface top thickness is 25mm plb with pvc beading allover, legs modesty wire manager made from 18mm thick plt having curved profile.made from plt ( prelaminated twin ) boards 18mm thick in two shades. a wire manager running along the width of desk fitted on the modesty panel from inside. cort corner table of size 530w x 450d x 450h built with the extremely durable rubberwood, with a very suitable cappuccino color, the table will complement any style of décor. the tapered legs provide stable support. it’s free of flaws design can accommodate your books, magazines, laptop and coffee mugs, all at once. the well thought out dimensions of the table make it easier to position it anywhere in the house. dt a ss canteen table with s.s top 8 seated with foldable stool size : l 2130 mmx d 915 mmx ht 750mm: under structure made of prime quality cold rolled close annealed square tube 30mm x 30mm x 1.2mm thick. with 8 nos. folding / tilting stools 4 on each side. stools fitted on specially designed c clamps over leg rest on each side with bush for smooth functioning. top 1.0mm thick, stainless steel properly bent & edge formed, supported with 12mm ply / plpb below the top. the stool top is made up of 1.0mm thick. stainless steel dia 30mm, supported on 12mm ply / plpb fitted with csk screw on 25mm x 3mm thick. ms flat welded on stool frame. all steel components are epoxy powder coated followed by seven tanks of anti corrosion treatment of the surface. fct file cabinet with 4 drawer width: 470mm, height: 1320mm, depth: 620mm , rigid knockdown construction, material: top, side & drawer frontmade from0.7mm thk **crca, drawer inside cover, side back side made from0.6mmthk **crca, back, bottom, drawer bottommade from 0.5mmthk **crca, **crcasteel confirming to is 513, grade d, label holder snap on type plastic label holder on drawer fronts, locking & anti tipping arrangement centralized lockingwith camlock& having antitipping arrangement to ensure that when one , drawer is opened for use, it does not allow other drawers to be opened, finish epoxy polyester powder coated to the thickness of 50 microns ( + / 10 ) . fp cbnt fire proof cabinet shall be designed to protect the contents ( paper media documents ) against the fire hazard.shell: the external shell of the cabinet shall be of steel of minimum 2 mm thick and internal shell of steel of 1.6 mm thick, both conforming to is 513. further fortified by suitable in situ insulating fire resistant barriers to meet the required protection. the overall protection to the contents shall be minimum 70 mm on all six sides. door: the external door of the cabinet shall be of steel of minimum 2 mm thick conforming is 513 and further fortified with hard plate over the lock for burglary protection and in situ insulating fire resistant barrier material to meet required fire protection.  bolt work: the door shall be secured by four way locking mechanism / bolt work with minimum 8 moving shooting bolts of 20 mm diameter. door & body fitment: the door fits in the cabinet having tongue and groove construction that stops hot gases and high temperature to pass through and withstand temperature up to 1010 deg.c. locking: the frrc shall be equipped with a dual control high precision key lock of minimum six levers. the lock body shall be of zinc alloy and the levers in the lock shall be of brass conforming to is 410. there shall not be any dummy lever in the lock. the storage capacity shall be minimum 650 liters with minimum usable internal sizes in mm as 1620 ( h ) x 670 ( w ) x 599 ( d ) .the cabinet shall be provided with minimum four nos. adjustable shelves. oc d office chair with seat / back assembly: the cushioned seat assembly consists of seat base moulded in glass filled poly amide, moulded polyurethane foam & upholstered with high stretch knitted polyester fabric. the cushioned back assembly consists of back inner moulded in polypropylene in situ moulded with polyurethane foam & upholstered with high stretch knitted polyester fabric. back size : 45.5 cm. ( / 1 / ) x 53.0 cm. ( h ) seat size : 48.5 cm. ( w ) x 49.0 cm. ( d ) high resilience ( hr ) polyurethane foam: the hr polyurethane foam used in seat and back cushion is moulded in density min 48 kg / m3, and hardness load 15 ± 2 kgf as per is:7888 for 25% compression. tilt mechanism, spines & spine connector: the seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. the cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. the s shaped spines moulded in high strength glass filled poly amide and the spine connector moulded in glass filled poly amide form the back spine structure involved in multi dimensional recline motion. the variable tilt angle recline motion can be adjusted with 3 position tilt limit feature which should be inbuilt in seat base and the tension ( return force ) should be user weight dependent. adjustable armrests: the assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled poly amide: the height adjustment feature should be button operated having adjustment of 6.6±0.5cm. the armrest top should be made up of integral skin pu moulded over plastic inner moulded in glass filled poly amide. pneumatic height adjustment: the seating height can be adjusted with a pneumatic gas lift having an adjustment stroke of 9.2 ± 0.3 cm pedestal assembly: the pedestal should be injection moulded in glass filled poly amide and fitted with 5 nos. twin wheel castors. the pedestal should be 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors twin wheel castors :5 nos. twin wheel castos are injection moulded in poly amide having 5.0 ± 0.1 cm wheel diamter assembled to the pedestal. ht hod table of size 1500 x 750 x 743 understructure: the understructure is in prelam panels, made with plt boards.drawer storage units with different combinations to support tops, made with 18mmplt boards of different colours. modesty and back panels, made with 18mm plt boards. the pedestals / storages are fitted with necessary locks plt board tops ( straight edges ) : wenge and savannah maple plt board used for making tops. pvc membrane tops ( with profiles ) : jdb job display board with dimensions ( 1200x900x150 ) mm board having 9 mm ply tdb tool display board ( 1200x900x150 ) mm board having 9 mm ply lt chem chemistry lab table of size 4130mm x 1540mm x 900mm with pp drop sink of size 560 x 355, single tap deck mounted 8 swing goose neck, ss peg board 550x420x55 with 25 pegs. two reagent shelves of width 1050 with glass shelf. c frames all cframes assemblies should be manufactured from standard hollow metal sections; confirming to i.s. code 7138:1973 ( indian standard specification for steel tubes for furniture ) and all sheet metal components should be of crca confirming to is code 513:1994. the suspended under bench welded units should be supported on heavy duty steel frames fully carrying the load of worktops. c frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. the c frame shall also have skirting at back bottom side. horizontal members should be made from rectangular pipes of 2mm thickness. lt n lab table of size 4130mm x 1540mm x 900mm frames all cframes assemblies should be manufactured from standard hollow metal sections; confirming to i.s. code 7138:1973 ( indian standard specification for steel tubes for furniture ) and all sheet metal components should be of crca confirming to is code 513:1994. the suspended under bench welded units should be supported on heavy duty steel frames fully carrying the load of worktops. c frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. the c frame shall also have skirting at back bottom side. horizontal members should be made from rectangular pipes of 2mm thickness. cross sectional dimensions of the pipe should be 60 x 30 x 2 mm. lu 4d locker unit with 4 door plu + lkr ( base ) with stand size 1830hx380wx450d, stackibilit the add on units can be stacked width wise to formbank of lockers having common side panel, locking cam lock with lock leveroption of hasp arrangement, material crca 0.6mmthickness, rigid knockdown construction, shelf uniformly distributed load capacity per each shelf level is 35 kg maximum, hat self 4 door model at the top, finish epoxy polyester powder coated to the thickness of 50 microns ( + / 10 ) .ventilation attractive punched pattern for ventilation lt b long table of size 1800 x 900 x 740 worktop 25 mm thick plb tops with 2mm thick pvc edge beading understructure c – frames legs 1.6 mm thick m.s c­frame supporting the top. legs dia. 38.1 x 1.6 mm thick m.s erw tube. dt b meeting table with 10 seater with wire manager of size 2400w * 1200d * 750h h top all tops are made from 25mm thick pre—laminated board with 2mm thick. pvc edge beading side panel all side panels are made from 25mm thick pre—laminated twin with 2mm thick pvc lipping of same color on sides and 0.8mm pvc lipping of matching color on the bottom curve, modesty these panels are made from 18mm thick pre laminated board with 0.8mm pvc lipping of matching color, access flap and switch mounting tray made from matt silver anodized aluminium extrusion and plastic moulded components to facilitate access of electrical / data voice. sockets from top, powder coated switch mounting tray made from 0.8mm and 1.2mm m.s sheet. switches to be mounted on tray as per requirement. provision for mounting 8 — module anchor roma switch plate on switch mounting tray. wire manager rehau made from rau pvc 1309 / 7558 ( black color ) nb notice board with size 4 x 3 surface material woolen felt / fabric in various colours, core material 9 mm thick soft board, backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour or 0.16 to 0.25 mm thick isi mark gp sheet, aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness rt da reception table double arch with dl top of size 2410 x 1065 x 725 worksurface, 1035 counter, d l top top clean matt pu finish 18mm thick inside radius 700.0 mm outside radius – 1350.0 mm depth – 650 mm glass frosted glass 10mm thick diamond cut finishing on edges inside radius – 1202.5mm outside radius – 1402.5mm depth – 200mm, modesty panel ms perforated sheet below worksurface : 0.8 mm ( thick ) x 665.0 mm ( height ) x 1345.0 mm ( flat length ) above worksurface : 0.8mm ( thick ) x 260 mm ( height ) x 1345.0 mm ( flat length ) , legs ms tube 1.6 mm thick diameter 50.8 mm height 604 mm. wb s non magnetic small white board 4 x 3 surface material 0.62 to 0.72 mm thick laminate sheet with extra melamine surface, core material 8 mm thick particle board, backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour, aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness. s al steel almirah of size 1981 x 916 x 486 mm multi bend construction and inter locking design and full length over apping doors and sides. three way bolting mechanism. spot welding & co2 welding. anticorrosion treated components, oven baked powder coating process. material thickness 0.9mm.top, bottom, lh & rh sides and back material thickness= 0.9mm, removable rh & lh main door with stiffeners material thickness= 0.9mm, 4 adjustable shelves of thickness= 0.8mm sr a steel rack of size 6x36x18 with six shelves prime quality crc sheet conforming to is 513d / 10748 / 5986. the pitches of the slots at 19.05 mm, panel / shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back ( minimum ) in mm 0.8, paint powder coated with lead free paint. ls lab stool of circular type 30.0 + / 0.5 cm and made up of 0.1+ / 0.012 cm thk cr steel. it is welded to the understructure and black powder coated ( dft 40 60 microns ) . understructure assembly: the understructure is made of ms tube 2.2 + / 0.03 cm x 0.16+ / 0.0128 cm thk ms erw tube. lt is welded ti the ms fabricated circular seat assembly and black powder coated ( dft 40 60 microns ) . the understructure is provided with black pp injection moulded ferrules. sr b steel rack of size 2 6x36x18 with three shelves prime quality crc sheet conforming to is 513d / 10748 / 5986. the pitches of the slots at 19.05 mm, panel / shelves: 6 bnd bending process of 905l x 448d of load capacity 80 kgs. udl max per shelf. shelf material 0.8 mm thick ms sheet conforming to commercial quality cr 1, grade 340 of is 513, angle posts material and size rolled steel angle posts of 40 x 40 x 1.8 mm, m s sheet thickness of shelves and back ( minimum ) in mm 0.8, paint powder coated with lead free paint. ot a office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18mm thick pre laminated top size 1199 x 590 x 735 mm with one side three drawer unit made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with lock. ct computer table of size 600w x 450d x 750h mm compact and easy to use . top made up of 1.5 cm medium density fiber. all the other panels are made of particle board. vacuum lamination of pvc has been done on the table to surface. 0.4mm lapping is used for all the other panels ot b office table made of ms erw round tube dia 25.4 x 1.2mm thick with 18 mm thick pre laminated top size 1365 x 680 x 735 ( approx. ) with both side drawer unit one side three drawers & another side two drawers made of .5mm thick crca sheet mild steel, all steel components have powder coated paint fitted with both side drawer lock pt principal table main desk of size 1800 x 900 x 740, eru of size 1550 x 450 x 705 made up of top 25 mm thick plain particle board ( ppb ) clad with 0.6mm thick post formed laminate and 1mm thick backing laminate ( bdl ) . flat edge duly sealed with 2mm thick pvc beading., modesty 18mm thick plain particle board ( ppb ) clad with 1.0mm thick decorative laminate ( dl ) on both sides. edge sealed with 2mm thick pvc beading with 01 no. 3 drawers free standing pedestal. ot c office table with eru & pedestal of size 1350 x 750 x 750 mm + eru + pedestel main desk of size 1350 x 750 x 750 with eru of size 1200 x 450 x 750 & 01 no. 3 drawers pedestal: top panel made from 25 ±0.5 mm thk pre laminated boards as per is 12823 with 2 mm thick pvc beading on all sides. side panel the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm pvc beading on all sides. modestty 1 & 2 the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm thick pvc beading on all edges. the panel is made from 25 ±0.5 mm thk pre laminated boards as per is 12823 with 2 mm thick pvc beading on all sides, the panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with 0.8 mm pvc beading on all sides. the panel is made from 18 ±0, 5 mm thk pre laminated boards as per is 12823 with 0.8 mm thick pvc beading on all edges. pedestal wooden panel ( 1 box+ 1 filling ) back wooden panel is made from 18 ±0.5 mm thk pre laminated boards as per is 12823 with pvc beading on all sides. the panel is made from 9 ±0.5 mm thk pre laminated board. sstp steel table with stainless steel top of size 1180 x 750 x 750. worktop the top is in stainless steel brushed finish with plb insert for durability. easy to clean and maintain hygiene. side frames made from 30mm x 30mm x 1.5mm thick m.s powder coated tubes at base which are welded and are fixed to top with screws. the bottom ends are closed with plastic buffers. ms shade : s / g metallic dark grey ( nerocoat 9000626 ) , cross member made from 30mm x 30mm x 1.5mm thick m.s powder coated tube, which is welded and bolted to side frames. tp a teaching platform with the dimensions of length 6 ft x breadth 4 ft x height 1.5 ft with 19 mm plywood on top, shall be rectangular hallow box shape without legs. tp b teaching platform with the dimensions of length 12 ft x breadth 6 ft x height 1.5 ft with 19 mm plywood on top, shall be rectangular hallow box shape without legs. pod wooden podium with dimensions: 45 h x 20 w x 15 d to 50 h x 25 w x 20 d presenter side height: 40 to 45 shelves: 20 h x 20 w x 10 d to 25 h x 25 w x 12 d product weight: 50 to 55 lbs. shipping weight: 65 to 70 lbs. material: scratch resistant high pressure laminate. the top of the table shall be provided 19 mm ost. the table shall be neatly finished and polished. smchr seminar chair with understructures could be revolving or fixed type as per need. option of hinge type and retractable desk let. desklet 100% voc free powder coating knock down design reducing transportation emissions designed for long life ot e office table of size 900 x 590 x 750 made of ms erw square tube 18 mm x 25mm x 1.2mm thick with pre laminated top size 1199 x 590 x 750 mm thick with single side one drawers, drawer unit made of .5mm thick ms crca sheet, all steel components have powder coated paint wb l non magnetic long white board 8 x 4 size and surface material 0.62 to 0.72 mm thick laminate sheet with extra melamine surface, core material 8 mm thick particle board, backing material 0.62 mm to 0.82mm thick laminate sheet with extra melamine surface mix colour, aluminium frame anodized 5 microns extruded aluminium section designation 63400 as per is:1285 2002 16 mm thickness. bkrk a double sided book rack with the dimensions width 900mm, height: 1850mm, depth: 600mm, rigid knockdown construction. construction, material crca0.8mmthickness, finish epoxypolyester powder coated to the thickness of 50 microns ( + / 10 ) .number of adjustable shelf: five adjustable shelves on one side ( total 12 loading levels ) . uniformlydistributed load capacity per each shelf is 80 kgmaximum. label holder & range indicator label holder & range indicator on eachmain unit for inserting labels. bkrk b single sided book rack with the dimensions width 900mm, height: 1850mm, depth: 316mm, rigid knockdown construction, material crca 0.8 mm thickness, finish: epoxypolyester powder coated to the thickness of 50 microns ( + / 10 ) ., number of adjustable shelf five adjustable shelves. ( total 6 loading levels ) . uniformlydistributed load capacity per each shelf is 80 kg maximum, label holder & range indicator label holder & range indicator on eachmain unit for inserting labels. m r magazine rack with overall dimensions of all steel periodical display rack shall be 900mm ( w ) x450mm ( d ) x1830mm ( h ) . rigid knockdown construction , panels shall be made from crca 0.6 mm thick and front frame shall be made from crca 0.8 mm thick . crca d grade as per is 513 . there shall be 5 level racks , display tray shall be suitable for fullscape size magazines, periodicals, aesthetically appealing metal tray at an angle for easy viewing . receding facility to access the storage behind . sliding on plastic rollers . behind storage shelving each of 5 level has a behind storage shelf . uniformly distributed load capacity per each shelf is 40 kg . leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns. glsd almirah with glass door size 916mm ( w ) x 486mm ( d ) x 1980mm # ( h ) # excluding leveler, construction & material • welded construction, • 0.7mm thk ( ±0.07mm ) crca* for shelf, • 0.8mm thk ( ±0.08mm ) high yield strength crca** for doors and back, • 0.9mm thk ( ±0.08mm ) crca* for all other components, crca ‘d’ grade as per is:513, crca ‘d’ grade high yield strength as per is:513, locking & handle • brass handle with • two way locking mechanism with shooting bolt, shelves • height wise adjustable shelf mounting • uniformly distributed load capacity per each full shelf is 40 kg maximum, • 4nos. of adjustable full shelf, • box file a4 size ( 85wx345hx285d ) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm, • m10 screw type leveler with hex plastic base, finish • epoxy powder coated to the thickness of 50 microns ( + 10 ) . dd dual desk is specially designed for rugged use with overall dimentions of l1054 x w980 x h760 mm and all edges are fillet. the desk is made of pressed formed ms crca section & crca tube fitted with pre laminated particle board top, seat & back with injection molded ppcp edge. hanger for water bottle and bag. space for keeping pen, pencil and scale. the overall appearance of the product shall be as per photograph. top injection molded ppcp edge. size : 1054x450x18 mm thk. particle board. seat injection molded ppcp edge. seat height : 450 mm , seat size : 1054x304x18 mm thk. particle board. back injection molded ppcp edge. back size : 1054x154x18 mm thk. particle board. shelf shelf 0.8 mm thk. crca sheet. bullnose front edge with stiffner 1 mm thk crca. modesty modesty 0.8 mm thk. crca sheet. slot perforated. tie members horizontal tie members 25x25x1.2 mm thk. crca pipe. footrest footrest pressed formed crca section 1.5 mm thk. side frame side frame c section pressed formed 1 mm thk.crca sheet welded with 25x50x1.2 mm thk tube. and back rest pipe ø25 x 1.2 mm thk. top end rounded. cap & levellers all pipe caps are curved ppcp material. finish all steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. drs t dressing table of size 460w x 486d x 1710h mm , mirror w x h: 362 mm x 1156 mm dressing table comes with a long mirror, two storage drawers, and a stool. available in wenge color, the dresser is crafted from good quality mdf wood, making it sturdy and lasting. the shelves of this stylish dressing table can be used to keep items like perfume bottles, hair products, and medicines, for that clutter free look. the stool, also wenge color with an orange colored cushion, offers comfortable seating, while the full length mirror is perfect to dress up, and check your overall ensemble. s al m steel almirah with mirror of size 900w x 507d x 1950h mm rafted from prime steel, your slimline cupboard will be resistant to corrosion and peststhis cupboard comes with 2 easily adjustable shelvesthe hanging rod inside the cupboard ensures ample space for your daily wear, suits, sarees and / or dressesknock down construction makes shifting and handling of slimline easieravailable with over head unit option to maximize vertical space usage you can also choose to have a mirror with slimlinestylish snap shut flush handle enhances slimline’s aesthetics. audi c auditorium chair seat / back assembly: the seat and back are made up of 1.2±0.1 cm. thick hot pressed plywood measured as per qa method described in ocp qlta p14 18 and upholstered with fabric and moulded polyurethane foam. the back is, flexing type.back size 47.0 cm. ( w ) x 51.0 cm. ( h ) , seat size 47.0 cm. ( w ) x 47.0 cm. ( d ) . 2. high resilience ( hr ) polyurethane foam: the hr polyurethane foam is moulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgf as per is:7888 for 25% compression.3. armrests :the one piece armrests are made of black integral skin polyurethane foam with 50 70 shore hardness and reinforced with m.s. insert. the armrests are scratch and weather resistant.5. understructure assembly: it is made of dia. 2.54±0.03cm. x 0.2±0.016cm. thk. m.s.e.r.w. tube with connecting strips made of 0.5 ± 0.05 cm. thk. hr steel welded to it for holding the seat. the assembly is powder coated ( dft 40 60 microns ) .the auditorium chair is designed to get mounted / grouted on floors with flooring specification as per engineer in charge.overall width 57.0, depth 57.0, height 86.0, seat height 44.0 cm. ss mc movable chair made out of stainless steel, understructure seat and back are made up of injection moulded high impact strength polypropylene polymer compound with indoor grade uv resistance *seat size: 52.5 cm. ( w ) x 53.2 cm. ( d ) , * back size : 51.6 cm. ( w ) x 40.5 cm. ( h ) .s.s. understructure: the tubular welded frame is made from dia 2.22 ± 0.03 cm x o.12 ± 0.0128 cm and 3.5 ± 0.03 cm x 1.5 ± 0.03 cm x 0.12 ± 0.0128 cm stainless steel 202 grade tube. the tubes are buff polished to give shiny finish. bd hostel bed made out of steel with overall size length 1994mm, width 907mm, height 822 / 623 / rest height 450mm, structure of metal bed frame including legs and head structure mild steel pipe, head board shape of headboard semi circular, thickness of hollow section in structure ( 1.2mm ) , support panel for placement of mattresses mild steel hollow box rectangular section, thickness of support panel ( in 1.2mm ) , material of head board mild steel erw tube is:7138 square tube of 38.1 mm x 1.2 mm thick, material of mattress panel ms perforated / sheet, thickness of mattress panel 1.2 ( mm ) , size of support members in mm ( ±5 mm ) 50 x 50mm, number of support members is 04 nos., paint / finish of all m s parts powder coating 60 micron. oc a office chair with seat and back are made from seasoned wood and plywood. the same is upholstered with black synthetic leather and polyurethane foam. back size 46.0cm ( w ) x27.0cm ( h ) . seat size 46.0cm ( w ) x40.0cm ( h ) . the armrest is gas assisted injection moulded from black polypropylene. the understructure assembly is a cantilever type frame.width of the chair 58cm, depth 56.5cm, height 87.5cm, seat height 48cm. sc study chair is made of blow molded high density polyethylene andis fixed on the understructure assembly with the help of stainless steel pop rivets.seat: seat is made of blow molded high density polyethylene and is fixed on the understructure assembly.understructure all side metal frames and cross connectors are made from mild steel erw tubes , 40 x 20 x 2mm thk ( approx. 14 swg ) as per 1s:7138 which are welded togetherthe welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. bag storage tray made of 04 mild steel rod ( as per 15:432 ) forms a cage at the bottom and is welded to the main understructure. seat support channel made of 1mm thk mild steel sheet ( as per is:513 ) is welded to the understructure for fixing seat. plastic caps plastic caps made of polypropylene are provided on the foot rest side tubes and back leg tubes adding more aestheic value to the product. st study table with all sides metal frames and cross connectors are made from mild steel erw tubes , 40 x 20 x 2mm thk ( approx. 14 swg ) as per 15:7138 which are welded together.the welded structures and cross connectors are coated with min 45 micron thickness of epoxy polyester coating. shelf tray and desktop mounting brackets made of 2mm thk mild steel sheet ( as per 15:513 ) are welded to the understructure for fixing shelf tray and desktop respectively. hooks are provided ori the vertical side frames on both sides of the desk for hanging bags / bottles. they are made from 09 mild steel rod ( as per 15:432 ) and are welded to the main understructure plastic caps: plastic caps made of polypropylene are provided on the foot rest side tubes and front leg tubes adding more aestheic value to the product....

Health And Family Welfare Department - Bihar

30458823 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler 1 fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 2 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 5 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 2 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 3 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 5 telephone socket outlet , s / f modular switch / socket on the existing modular plate 6 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 7 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 2 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 1 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 2 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 4 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 5 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly : . , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30458807 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler 1 fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 2 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 5 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 2 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 3 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 5 telephone socket outlet , s / f modular switch / socket on the existing modular plate 6 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 7 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 2 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 1 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 2 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 4 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 5 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly : . , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30458798 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler 1 fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 2 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 5 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 2 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 3 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 5 telephone socket outlet , s / f modular switch / socket on the existing modular plate 6 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 7 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 2 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 1 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 2 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 4 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 5 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly : . , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30458765 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 1 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 1 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 2 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 3 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 1 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 2 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 3 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 telephone socket outlet , s / f modular switch / socket on the existing modular plate 5 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 6 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray 2 upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 5 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends”3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing 1 earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 2 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 4 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 5 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 7 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30458761 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler 1 fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 2 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 5 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 2 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 3 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 5 telephone socket outlet , s / f modular switch / socket on the existing modular plate 6 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 7 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 2 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 1 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 2 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 4 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 5 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly : . , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30457596 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler 1 fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 2 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 5 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 2 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 3 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 5 telephone socket outlet , s / f modular switch / socket on the existing modular plate 6 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 7 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 2 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 1 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 2 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 4 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 5 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly : . , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30457511 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler 1 fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 2 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 5 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 2 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 3 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 5 telephone socket outlet , s / f modular switch / socket on the existing modular plate 6 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 7 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 2 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 1 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 2 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 4 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 5 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly : . , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30456419 bids are invited for pile boring, providing and installation bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using direct mud circulation ( dmc ) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads ( length of pile for payment shall be measured up to bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , upvc door providing and fixing of factory made upvc white colour casement door, upvc multichambered extruted frame, sash and mullion profile. frame duly reinforced with 1.2mm gi section box tpe chamber and sash with 1.5mm thick gi section ( ± 0.2mm ) based on wind load calculations ( shape and size according to upvc profiles ) , appropiate dimentions of upvc extruded glazing bead, epdm gasket ( k / o type ) , seperate drainage system, ss34 grade friction hinges 2d / 3d plate hinges, zinc alloy ( white powder coated ) casement handle, gi fastener 8x100 mm size for fixing frame to finish wall, plastic packer and caps and necessary steel screws etc.profile of frame and sash shall be metered cut and fusion welded at all corners, mullion shall be also fusion welded / joined mechanically including drilling of holes for fixing hardware and drainage of water etc. after fixing of frames , gap between frame and adjascent wall shall be filled with pu foaam / backer rod required size and the approved quantity. after that sealed with weather proof silicon sealant at both side, all complete as per approved drawing and direction of eic , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 1 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge :flamed finish granite stone slab jet black, cherry red, elitebrown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item ( galvanised@80gsm ) 50 mm long 8mmouter diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’ , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975. the wind load shall be as per provisions of is 875 ( part iii ) . lgsfs frame shall be designed as per is: 801 using commercially available software such as frame cad pro 11.7 / staad pro v8i / architekv2.5.16 / revit architecture 2011 or equivalent. proper usage of connection accessories like heavy duty tension ties, light duty hold ons, twist straps ( to connect truss with wall frames ) , strong tie, tie rod, h brackets, boxing sections, l shaped angles for better structural stability. the framing section shall be cold form c type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple / slot at required locations as per approved drawings. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , face panel providing and fixing in all exterior face panels breathable vapour barrier underneath the cementfiber board as per national building code 2009 complete as per direction of engineer in charge. , lap siding supplying and installation of moisture resistant / fire resistantlap siding 8 mm thick and width as per standard sizes made ofiber cement board with embossed decorative finish to give pleasing exterior fixed horizontally with staggered joints including minimum over lapof 32 mm external cement fibre boardconforming to is 14862:2000 offixed with self drilling / taping screws / fastners of approved make. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1 new work ( two or more coats ) over and including water tinnable priming coat with cement primer , ex. paint finishing walls with textured exterior paint of required shade : new work ( two or more coats applied @ 3.28 ltr / 10 sqm ) over and including priming coat of exterior primer applied @ 2.20kg / 10 sqm sqm , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel 1 steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , road providing and laying c.c. pavement of mix m 25 with ready mixed concrete from batching plant. the ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer in charge. ( the panel shuttering work shall be paid for separately ) . ( note: cement content considered in this item is @ 330 kg / cum. excess / less cement used as per design mix is payable / recoverableseparately ) . , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 1 providing & fixing stone slab table rubbed, edges rounded and polished of size 75 x 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size ) as per engineer in charge and finished smooth white agaria marble stone , phe 2 providing and fixing salem stainless steel a isi 304 ( 18 / 8 ) kitchen sink as per is: 13983 with ci brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. kitchen sink with drain board510x1040mm bowl depth 200mm. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing:rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixturescomplete, including cutting and making good the walls andlevel whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings andfloors wherever required :white vitreous china orissa pattern w.c. pan of size580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 9 providing and fixing cp brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.. ( sink & urinal ) , phe 10 providing & fixingptmt towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealedfittings arrangement of approved quality and colour weighing not less than 88 gms , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size 660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 15 providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption ) , having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of engineer in charge.. , phe 16 providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. , phe 17 providing and fixing white vitreous china laboratory sink with c.i. brackets, c.p. brass chain with rubber plug, 40 mm c.p brass waste and 40mm c.p. brass trap with necessary c.p. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :size 600x450x200 mm , phe 18 providing and fixing cp brass single lever telephonic wall mixer of quality & make as approved by engineer in charge . a ) 15 mm nominal dia. , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 21 providing and fixing ptmt liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 24 two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand andmanufacturetwo more coast on new work , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm.clear depth and 250mm apron including cost of e / w. involved with 75mmcement concrete ( 1:4:8 ) over one brick designation 100 a flat soling inproper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 8 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia. exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 11 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 450 mm dia rcc pipe , ex. phe 12 inside size 120x90 cm and 90 cm deep including c.i. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg ) :with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , ex. phe 13 providing and fixing square mouth sw gully trap grade ‘a’ complete ci grating brick masonry chamber with bricks of class designation 75 and water tight ci cover with frame of 300 x 300 mm size ( inside ) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. ( cover min. 4.5 kg & frame min.2.7 kg ) 180x150 mm size p type with fps bricks , ex. phe 14 constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement:4 coarce sand ) for stop cock complete with c.i. surface box 100x100x75mm ( inside ) with locking arrangement and rcc top slab 1:2:4 mix ( 1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size ) necessary excavation foundation concret 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design. , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , ex. phe 16 structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. , ex. phe 17 making connection of gi distribution branch with gi main of 50 80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. , rain water harvesting 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , rain water harvesting 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , rain water harvesting 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150 mm nominal size dia , rain water harvesting 4 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 5 supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , rain water harvesting 7 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , rain water harvesting 8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , rain water harvesting 9 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 , tubewell 1 boring / drilling bore well of required dia for casing / strainer pipe, bysuitable method prescribed in is:2800 ( part i ) , including collecting sample from different strata , preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of engineer in charge, upto 90m depth below ground level.300 mm dia , tubewell 2 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.150mm nominal size dia , tubewell 3 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing ( cm ) pipe of required dia, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100mm nominal size dia , tubewell 4 supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen ( rms ) pipes with ribs, conforming to is: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of engineer in charge.100 mm nominal size dia , tubewell 5 supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of engineer in charge. , tubewell 6 providing and fixing bail plug / bottom plug of required dia to the bottom of pipe assembly of tube well as per is:2800 ( part i ) . 100 mm dia , submersible pump 35m deep boring with casing and pipe. supply of pipe etc supplying & installation of suitable 2hp submersible pump b.s or k.s.bor equivalent make with finolex cable 1x3x2.5 squmm ( upto 50mtr ) withflexible conduit 25mm dia, electrical out door pannel with required electrical fitting such as mcb of 0 25amp ( havell or indocopp or mds make ) , volt & ampere meter ( ae make ) , single phase preventer ( minilac or vsp 1 make ) starter ( l&t or bch make ) etc of approved make, 40mm hdpe pipe ( 25 mtr ) and all accessories complete as per requirement of site. , water purifier and cooler fitting and fixing single faucet storage type water cooler ( size 461 mm wide x 582 mm deep x 1217 mm height, weight 46 kg ) fully stainless body having storage capacity of 40 ltrs, cooling capacity of 40 ltrs. / hr. with hermetic type compressor, gas cooled motor equipped with over load protector, condensor for propeller type, thermostat autometically controlled temperature, refrigerent r 22, 230 volt, single phase 50 hertz, maximum current 2.3 amp including plug top and electrical lead wire connection upto 3 metres from the cooler, water inlet and drain out connections complete in all respects of voltas model no 40 / 40 tushar pss type or similar type of approved make. , water purifier and cooler 1 fitting and fixing water purifier for drinking purpose of capacity 6 litres / min, 5 purification system with reverse osmosis system with ultra ventilated membrane, tds500 to 2000 mgl / ppm, auto shut off with microswitch float manual flush facility, tds reduction 90% having automatic backwash system with filteration unit along with all accessories including plug top and electrical lead wire connection upto 3 metres from the purifier, water inlet and drain out connections complete in all respects similar to aquaguard or similar approved make ( model aquasure elegant ro water purifier of size width 360 mm x height 430 mm x depth 235 mm and weight 8.5 kg ) . , fire extinguisher 1 providing and fixing carbon di oxide type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. capacity 4.5 kg. , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 6.0 kg. , electrical 1 wiring for light point / fan point / exhaust fan point / call bellpoint with 1.5 sq.mm frls pvc insulated copper conductorsingle core cable in surface / recessed steel conduit, withmodular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required. group c , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , pvc conduit 1 supplying and fixing of following sizes of medium class 20mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 2 supplying and fixing of following sizes of medium class 32mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , pvc conduit 3 supplying and fixing of following sizes of medium class 50mmpvc conduit along with accessories in surface / recessincluding cutting the wall and making good the same incase of recessed conduit as required. , electrical 4 wiring for light / power plug with 2x4 sq. mm frls pvcinsulated copper conductor single core cable in surface / recessed conduit alongwith 1 no. 4 sq. mm frls pvcinsulated copper conductor single core cable for loop earthingas required. , wiring frls pvc insulated copper conductor 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 1 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 2 4 x 6 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 3 4 x 10 sq. mm + 2 x 6 sq. mm earth wire , wiring frls pvc insulated copper conductor 4 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 1 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 3 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 4 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 1 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 2 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 3 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 4 telephone socket outlet , s / f modular switch / socket on the existing modular plate 5 tv antenna socket outlet , s / f modular switch / socket on the existing modular plate 6 bell push , electrical 5 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, “c” curve including connections, painting etc. as required. ( for ac / geyser ) , electrical 6 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 11 supplying and fixing 20 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 12 supplying and fixing 30 a, 415 v, tpn industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 a c curve, tpmcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , electrical 14 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 12 way , double door , electrical 15 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 16 way, double door , electrical 16 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 6 way ( 4 + 18 ) , double door , electrical 17 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way ( 4 + 24 ) , double door , electrical 18 supplying and fixing of following ways surface / recess mounting, vertical type, 415 v, tpn mcb distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 a tinned copper bus bar, common neutral link, earth bar, din bar for mounting mcbs ( but without mcbs and incomer ) as required . ( note : vertical type mcb tpdb is normally usedwhere 3 phase outlets are required. ) 4 way ( 4 + 12 ) , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 63a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , 100a 4p mcb supplying and fixing of following mcbs, 415 volts, c curve, miniature circuit breaker suitable for inductive load offollowing poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , l / f pvc sheathed / xlpe power cable in trench laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 95 sq. mm and upto 185 sq. mm , l / f pvc sheathed / xlpe power cable in trench 1 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. above 185 sq. mm and upto 400 sq. mm , l / f pvc sheathed / xlpe power cable over cable tray 2 upto 35 sq. mm ( clamped with 1mm thick saddle ) , l / f pvc sheathed / xlpe power cable over cable tray 3 above 35 sq. mm and upto 95 sq. mm ( clamped with 25x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 4 above 95 sq. mm and upto 185 sq. mm ( clamped with 25 / 40x3mm ms flat clamp ) , l / f pvc sheathed / xlpe power cable over cable tray 5 above 185 sq. mm and upto 400 sq. mm ( clamped with 40x3mm ms flat clamp ) , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3.5c x 300 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 1 3.5c x 240 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 2 3.5c x 120 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 3 3.5c x 95 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 4 3.5c x 50 sqmm, aluminium conductor cable a2xfy , s / m end termination with brass compression gland and aluminium lugs aluminium conductor cable of 1.1 kv grade 5 4c x 35 sqmm aluminium conductor cable a2xfy , cable tray 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 100 mm width x 50 mm depth x 1.6 mm thickness , cable tray 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness , cable tray 3 supplying and installing following size of perforated hot dipped galvanised iron cable tray ( galvanisation thickness not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required. 600 mm width x 62.5 mm depth x 2.0 mm thickness , cable tray “bends” supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.100 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 1 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.150 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends” 2 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.300 mm width x 50 mm depth x 1.6 mm thickness , cable tray “bends”3 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.450 mm width x 50 mm depth x 2 mm thickness , cable tray “bends” 4 supplying and installing following size of perforated hot dipped galvanised iron cable tray “bends” ( galvanisation not less than 50 microns ) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with g.i. suspenders including g.i. bolts & nuts, etc. as required.600 mm width x 62.5 mm depth x 2.0 mm thickness , mv cable supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 300 sqmm, aluminium conductor cable a2xfy , mv cable 1 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 240 sqmm, aluminium conductor cable a2xfy , mv cable 2 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 120 sqmm, aluminium conductor cable a2xfy , mv cable 3 supplying following 1.1kv grade, xlpe insulated, frls type, heavy duty armoured cables suitable for 415v, 50hz, ac system, with inner and outer pvc sheath, outer sheath provided with frls insulation, galvanised steel armouring ( round ( w ) or flat ( f ) as mentioned ) and with all components as mentioned , specifications, complete as required.3.5c x 95 sqmm, aluminium conductor cable a2xfy , earthing 1 earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 2 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 3 earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required. , earthing 4 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 5 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , earthing 6 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. , earthing 7 providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : , fiting & fixtures 4 supplying and fixing recess mounted 12 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 6 supply, installation, testing and commissioning of 400 mm sweep, 65w, blade material aluminium blades , speed & oscillation 3 speed, pull cord for speed and oscillation.air delivery minimum 72 m³ / min, speed minimun 1350 revolution per minute.suitable for 230 v, 50 hz, single phase ac supply, earthing etc. complete as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , fiting & fixtures 8 supplying installation testing & commissioning ofb22 based 9w led 3 star bulb with 850 lumen, 6k color temperature including holder. , fiting & fixtures 9 supplying installation testing & commissioning of black painted extruded aluminium housing. green / red led’s mounted inside the housing. laser engraved signage matter on single / double acrylic sheet fixed on one side suitable for wall / ceiling / suspension type single / double sided display. in double sided version black paper is inserted. ni cd battery back up to 2 hrs. ( charged up to 8 10 hrs ) .mounting strings provided for pendent mounting operating voltage 150 280v ac ambient operating temperature. – 0 to 450c ingress protection – ip42.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required.   220208 besl 03 led ssd wbb green 240 3 8wor220209 besl 03 led ssd wbb red 240 3 8wor220210 besl 03 led dsd wbb green 240 3 8wor220211 besl 03 led dsd wbb red 240 3 8w , fiting & fixtures 10 supply, installation, testing & erecting of ip66 bulkhead surface type lighting fixture 10w made up of pressure die cast aluminium housing and polyster powder coated die cast aluminium with high quality polycarbonate diffuser in opal finish for glare free light distribution.high efficiency long life led module with smd led package mounted on mcpcb with lumen efficacy of >95 lm / w with system lumen 950. powered by integral electronic led driver with apfc with low thd output short / open circuit protection. cct 5700, cri>80, system efficacy>90lm / w, thd<15%, pf>.95, ip66, ik 10, life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz.including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. cat ref: havells : hexaft10wled857ssymbopc or approved equivalent. , civil & misc works1 providing and fixing m.v. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works2 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. , civil & misc works3 supplying and making cable route marker with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm x 60 cm at the bottom and 50 cm x 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. , civil & misc works4 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. , civil & misc works5 providing & fixing in position 1000 mm wide , electrical insulating rubber mats as per is 15652:2006, 2 mm thick, suitable up to 1.1 kv , fire retardant, no effect of acids, alkalis and transformer oils, moisture proof, high tensile strengthandtexture finish / cloth impression ( anti slip , marking on top ) , civil & misc works6 supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as required ( approx front area 1.20 sq metre ) , 40 kvaups supplying, installation, testing and commissioningof online double conversion fully microprocessor based , indoor type, compact ups system of following rating with igbt based pwm technology to achieve thd < 3% and input power factor of greater than 0.95 at 50% loading, suitable for three phase ac input voltage 380 v to 440 v, 50 hz +3% / 3 % and three phase ac output voltage 415 ± 1% volts & frequency 50 ± 0.5 hz , inbuilt isolation transformer, necessary vrla batteries of suitable size having 30 minutes back up time , mounting rack including and suitable size connecting cable ( for ups to battery and battery to battery ) , static and maintenance bypass switch, snmp card for rs232 / ethernet ip computability for operation and monitoring etc. with all components as mentioned , specifications, complete as required.note : concerning vendor needs to furnish the battery sizing calculations at the time of ga approval and battery size has to be as per the approved ga drawing. , external lighting 1 supply and erection of 4 metre height hot dipgalvanized octagonal street light pole with followingarm with top dia 70 mm and bottom dia a / f 130 mm, made of 3 mm thick sheet along with base plate of size220 x 220 x 12 mm , small door opening for junctionbox mounting with mcb & connector, cement concreteof 1:3:6 including excavation, refilling and suitable sizefoundation bolts with template and all complete jobasrequired. ( but without pole collar ) single arm , external lighting 2 supplying and fixing 40 / 45 watt led type street lightwith die cast aluminium housing for ingress protectionof ip65 and complete with all accessories etc, onpole / building including connection with fr pvcinsulated copper conductor cable and earthing thebody etc. as required. , ip based cctv system 1 sitc of 2 megapixel @ 25fps, h.265 ip bullet camera, 1 / 2.9 cmos with 2.8~12mm varifocal lens, 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 2 sitc of 2 megapixel @ 25fps, h.265 ip dome camera, 1 / 2.9 cmos with 3.6 fixed mm 0 lux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 3 sitc of 2 megapixel @ 25fps, ptz camera h.265 ip dome camera, 1 / 2.9 cmos with 2.6 fixed lenslux with night vision ir up to 30 mtrs.support intelligent analytics like abnormal video signal detection, video mask, heartbeat, password protection. supports digital wdr, icr, true d / n, 3d dnr, roi coding, poe, onvif, ip66 etc. complete as required. , cctv 4 sitc of 32ch 4k ivr , h.265 / h.264 • 1080p real time • 4k display • dual lan • 8x hdd • raid •web plugin free h.265 / h.264 compression technology 4k display for clear monitoring up to 1080p 16ch decoding ability smart search ii smart vca event searchsupport raid 0, 1, 5 supported to prevent from recording data loss browsers supported: ie , smart functions : target count, electric fence, face detection, humaniod detection, retrograde detection, leave position detectio output, local & network backup etc. complete as required. , cctv 5 sitc of harddiskdrive8tb, 24 / 7surveillance category only complete etc as required.etc.all complete , cctv 6 sitc of 55 led narrow bazel for monitoring for nvr server etc. all complete. , cctv 7 sitc of rj 45 outlets near the cameras etc. all complete. etc. all complete. , cctv 8 sitc of cat 6 patch cords 1 meter high quality four pair twisted stranded cable terminated with rj45 modular plugs at both the ends. , signage 1 providing & fixing of building direction signage mounted on pole, with pole of 100x100mm shs ( square hollow section ) of height of 5600mm, and sign size of 900x1050, sign made of aluminiu c section of 60mm with internal framing to support the frame in ms tubes hollow section, frame work duly painted with anti rust coatings, with facia of 3mm thick exterior grade aluminium composite panel, cladded with uv cured digital printed retroreflective sheet of 3m make, and back panel of 3mm exterior grade acp, all pipes to be painted in approved color. cost shall includecost towards installation, including excuvation and filling up with specified pcc and fixing of foundation bolts as specified, also it shall include the designing charges.all complete as per direction by engineer in charge. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , 2 tr air conditioning 1 split ac ( inverter model ) : supply, installation, testing, commissioning of split type wall mounted air conditioning units of following capacity including inddor, outdoor unit fitted with inverter based rotary compressor fitted with rotary compressor, copper condensor and first charge refrigent r410a / eco friendly green gas only, all complete including all electrical connections to the electrical power supply system of the building, includingbut not limited to supply of all electrical plugs, etc., as necessary, lengthening of all electrical wires of ac units ( both indoor and outdoor ) , drain pipe andincluding suitable voltage stabilisers, etc. so as to place them in a concealed manner in the desired position. the copper pipes and electrical cables shall be concealed in approved manner and neatly run in straight lines in a workman like manner with proper supports. complete supply and installation of split2 tr star rating 3 star , refrigerant piping copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 25 mm od, wall thickness >= 1.2 mm ( insulation 19 mm thick ) , refrigerant piping 1 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 19.1 mm od, wall thickness >= 1.0 mm ( insulation 13 mm thick ) , refrigerant piping 2 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 15.9 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , refrigerant piping 3 copper piping: supply, installation, providing, testing and commisioning of interconnectiong copper refrigent pipe work ( 19mm / 13 mm thick ) duly insulated with elastomeric nitrile rubber, joints shall be covered with nitrile tape of 3mm thick complete as per specification soft refrigerant copper piping as per specifications and drawings. 9.5 mm od, wall thickness >= 0.8 mm ( insulation 13 mm thick ) , drain piping providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 20 mm , drain piping 1 providing and fixing of cpvc 6 kg / cm2 drainpiping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings. 32 mm , main oxygen manifold supply, installation, testing and commissioning of following gas manifold system ( excluding cylinders ) . the manifold is configured for designed numbers of cylinders and is suitable to withstand a pressure of 145 kg / cm2, along withhigh pressure copper annealed tail pipes with end brass adapter suitable for cylinders and manifold. top frame comprising of high pressure copper pipes of size 1 / 2” nb x 15swg with high pressure brass fittings made of high tensile brass and connections through nonreturn valves, the design of middle and bottomframes is provided to fit both round and flat bottom cylinders safely. the manifold is tested ( hydraulically ) at 3500 psig. ( it should be ce and iso 13485 certified ) mani fold oxygen manifold 6 + 6 cylinder banks complete with nrv, middle frame, bottom frame with ce marked, , emergency manifold emergency oxygen manifold 01 + 01 cylinder emergency manifold with complete regulator, nrv, middle frame & bottom frame, , control panelfor oxygen fully automatic three port control panel for oxygen supply, installation, testing and commissioning of automatic manifold control panel would provide a duty or standby gas supply from two cylinder banks with automaticchangeover the manifold indicates local status and has a remote indicator facility. automaticmanifold control panel would be designed to supply the mgps with a constant pressure supply via a control panel form two equal banks of cylinders and the changeover from the ‘duty’ to the ‘standby’ bank of cylinders would beautomatic. automatic changeover from the duty to the standby bank would occur at a cylinder pressure that will ensure the maximum usage of the contents of the duty bank. the changeover unit would be provided with monitoring todetect and display: duty bank operating, duty bank empty, standby bank operating, and standby bank below 10 % when the duty bank is empty, reserve bank low, pipeline pressure fault. there would be facility to connect liquidoxygen supply ( i.e. three port control panel ) ( it should be ce and iso 13485 certified ) fully automatic three port control panel for oxygen , emergency manifold line regulator emergency manifold line regulator supply, installation, testing and commissioning of emergency manifold line regulator i n p u t p r e s s u r e 1 5 0 k g / c m 2 working pressure 4 kg / cm2 it should be ce and iso 13485 certified.oxygen input pressure 150 kg / cm2 working pressure 4 kg / cm2capacity : 1500 lpm , cylinderconnectingpipe ( pig tail ) supply, installation, testing and commissioning of cylinder connecting pipe ( pig tail ) made up of flexible ss hose with safety cord 5 / 8 inch bsp gland nut and one side 1 / 2 inch bsp internal threads having one meter length. ( oxygen 24 , n2o 10, co2 4 ) , backpressurecompensated [ bpc ] oxygen flowmeter supply, installation, testing and commissioning of back pressure compensated [ bpc ] oxygen flow meter body should be made of brass material dully chrome plated and graduated from 0 15 l / m on an expanded lower scale forprecision setting at low flow and 5 15 l / m for general use. the humidifier bottle should be made up of unbreakable polycarbonate / polysulphone material and autoclavable at 121 degree centigrade temperature. it should be ceand iso 13485 certified. , oxygen gas outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , medical air ( 4 bar ) outletfront loadeddin / bsstd gas outlet front loaded din / bs std:supply, installation, testing and commissioning of din / british standard gas outlets are for use with medical gas system. the gas outlets completely complywith htm2002 and c11 standard regulations and pass the test of leakage and connector stability. medical gas outlet shall be gas specific for the services indicated and accept only corresponding din / british standard quickconnect adapter. specifically, gas specific indexed to eliminate interchangeability of gas services. the gas outlet is offered in consoletype, wall type with box and hose barb type gas system. it should be ce and iso 13485certified. din / bis std. gas outlets feature and benefits:* comply with htm2002 and c11 standardregulations* color coded according to iso32 color*100% pressure and leak tested* full range of mounting options* available in wall type with box, console typeand hose barb type* gas specific adapters , quickconnectadapter din / british standard quick connect oxygen adapter ( safety probe ) , tube oxygen h.p. rubber tube white color, , alarm supply, installation, testing and commissioningof area pressure alarm panel would be witdigital display, closed circuit, self monitoringtype. the alarm would be designed to monitorthe line pressure in piping systems.it should be ce and iso 13485 certified. withfour digit notified no. area line pressure alarm 1 gases , isolation valve, supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified.42mm , isolation valve 2 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 28mm , isolation valve 3 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 22mm , isolation valve 4 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 15mm , isolation valve 5 supply, installation, testing and commissioning of the ball valves [ for dividing the pipelines into various zones for the case of maintenance ] the internal ball with full borne is made of stainless steel with teflon seats. these valves are leakproof and needs only quarter turn for its operation [ either fully open or fully closed ] . it should be ce and iso 13485 certified 12mm , pipeline 1 medical grade copper pipeline ( in mtrs. ) as per en 13348, 12 mm ( od ) x 0.7 mm thickness , pipeline 2 medical grade copper pipeline ( in mtrs. ) as per en 13348, 15 mm ( od ) x 0.9 mm thickness , pipeline 3 medical grade copper pipeline ( in mtrs. ) as per en 13348, 22 mm ( od ) x 0.9 mm thickness , pipeline 4 medical grade copper pipeline ( in mtrs. ) as per en 13348, 28 mm ( od ) x 0.9 mm thickness , pipeline 5 medical grade copper pipeline ( in mtrs. ) as per en 13348, 42 mm ( od ) x 1.2 mm thickness , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 2268 mm x ( w ) 922 mm x ( h ) 610 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sandwitchconstruction: round corners yeshitlon thickness ( mm ) : 60hitlondensity ( gm / dcm3 ) : 23coir ( both side ) thicknessmm: 20density ( gm / dcm3 ) : 70, drc ( % ) : 22quilting combination / layers:pilled foam – quilting ( one side ) thicknessmm 14pilled foam density gm / dcm3 18pu foam / epe sheet side walling thicknessmm 3total mattress thickness mm 87rexine ( gsm ) : 150note: * finish product thickness should be measure from outer to outer surface. tolerance +5 mm , paediatric bed with mattress paediatric bed of overall sizes in mm: 1500 ( l ) x 850 ( w ) x 1210 ( h ) flat single section bed with grille frame on 4 sides.suitable for children up to 12 years.drop down grill frame on both sides for protection of the patient.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral white , bed side locker type i over all dimension :402mmlx422mm wx840mm ht .locker should have one cabinet and one drawer unit .both provided with cam lock .there should be gap between drawer and unit to keep general items for frequesnt use castors are provided for easy handling .drawer made up of crca sheet 1 mm thick and has ball slide for easy operation .top ss 304 sheet 0.8 mm thick castors 50 mmdia , hamdle abs ..powder coating of epoxy polyester , medicinetrolleytype i overall size902mm ( l ) x532mm ( w ) x915mm ( h ) .top shelf should be made of ss 304 sheetof 1 mm thick. supporting legs made of ss304 tubesection 30.30 mm dia.of 1.2 mm thick provided to suppoort the entire structure.ss 304 tube provided at the bottom for placement of instument being used .handle made up of ss 304 tubeof dia dia 16 mmand thickness 1.2 mm provided to handle trolley .and maneuver accordingly. high endurance anti static plastic injection moulded castors of 125 mm dia.ss should be finished in glossy mirror finish. max load capacity of 10 kg / shelf udl , round stooltype i overall sizes diagonal legdia 538 mmh470 min 655max.ss 202 made sheet with spin section of thickness 1mm & should be non corrosive. it should have a diameter of 305mm, seat base is made of ms ring and rectangular tube.en8 screw having dia of 22 mm should be used for height adjustment of the seat base.the hub should be made of ms erw tube having dia of 38mm and thickness 2 mm.the hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.the understructure should consist of 4 legs made up ofms erw tube of diameter 25.4 mm and 1.6mm thick. the press formed pipe leg should give a round & clean look. all the legs should be provided with 4 nos of nylon 6 bush.all metal componentsshould be pre treated with zinc phosphating in 9 tank process and then powder coated with anti microbialepoxy polyster powder coating . all welding should be co2 argon welding to minimise rusting on the welding areas.safe working load must be 135kg , strecher on trolley type i 2005mm ( l ) x666mm ( w ) x827mm ( h ) .the trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick erw tube.holder for stretcher should be made up of mild steel.castor should be of 200 mm dia , diagonal locking castor.stretcher should be made up oferw tubeof dia 25.4 mm and thickness 1.6 mm.top sheet should be made of crca sheetof thickness 1.2 mm with contour shape to accommodate patient.iv pole holder should be made ofms .maximum safe work load should be 135 kg.to ensure qood quality welding co2 argonprocess should be adhered to.all metal componentsshould be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbialepoxy polyster powder coating.goods should be supplied in knocked down construction to reduce carbon emission. performance test :proof loading test , cycle tests , impact test, salt spray test, castor break test, the manufacturer should compilant with iso 9001, 14001, 13485, ohsas 1800 and ce certification. , doctor desk type x s / f / f executive table main desk should be of dimesion : 1350w x 750d x 750h.the table top should bein white cedar, side panelsin black, while the modestypanel ina combination of black & white cedar. side panels : ( black ) made form 18mm thick plt with pvc lipping.modesty panel : made form 18mm thick plt with pvc lipping. bigger upper panel in black and smaller lower panel in white cedar. made from 18mm thick plt with pvc lipping. mobile pedestal : one box and one filing drawer with 18mm thick plb fronts and top. handles : black powder coated die cast aluminum alloy handles. mobile pedestal and hdu are fitted with central lock. , chair type iii s / f / f executive chair1 ) seat / back assembly: the seat and back are made up of 1.2 cm. thick hot pressed plywood, upholstered withfabric upholstery covers and moulded polyurethane foam. the back foam is designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area.high back size : 47.5 cm ( w ) x 69.5 cm ( h ) seat size : 47.0 cm. ( w ) x 48.0 cm. ( d ) 2 ) polyurethane foam: the polyurethane foam is moulded with density = 45 + / 2 kg / m 3and hardness = 20 + / 2at 25% compression. 3 ) armrests: the one piece armrests are injection moulded from black co polymer polypropylene. 4 ) center tilt synchro mechanism : the mechanism is designed with the following features:• 360 revolving type. • upright position locking. • tilt tension adjustment.• seat / back tilting ratio of 1:3 ( 60 seat tilt / 180 back tilt ) . 5 ) pneumatic height adjustment : the pneumatic height adjustment has anadjustment stroke of 12.0 cm. 6 ) telescopic bellow assembly : the bellow is 3 piece telescopic type and injection moulded in black polypropylene. 7 ) pedestal assembly , staff / visitor chair type i chair of over all size: 58.0cm ( w ) x 56.5cm ( d ) x 87.5cm ( h ) & 48.0cm ( sh ) seat / back assembly: the seat and back are made from chemically treated and seasoned wood, upholstered with plywood, black leather cloth, and u foam.*back size: 46.0cm ( w ) x 27.0cm ( h ) .*seat size: 46.0cm ( w ) x 40.0cm ( d ) .armrest tube: the armrest tube is made of m.s. e.r.w. tube dia. 2.54cm. ( 1” ) x 16bg thick and powder coated.armrest: the armrest is gas assisted injection moulded from black polypropylene.understructure assembly: the understructure assembly is a cantilever type frame made of dia. 2.54cm. ( 1” ) x 14bg. thick m.s. e.r.w. tube and powder coated. , wheel chair type i ( l ) 790 x ( w ) 600 x ( h ) 870mm.foldable frame structure should be made of section 22diax1.2mm a3 carbon steel with chrome finish. cross bar should be made of a3 carbon steel with section 25.4 x 1.2mm.rear wheel:24 inch solid mag wheels with alloy in the rim .integrated handrim provide to drive the wheel chair of section 16x1.2mm a3 carbon steel with chrome finish.front wheel :8 inch hub made of pa polymer and outer with solid rubber.pu molded arm rest & base should be made of abs for better arm support .leatherite strap for calf rest & leatherite cushion for seat.adjustable alluminimum die cast foot rest with updown & swivel type mechanism.handles should be made of moulded rubber grip to push the wheelchair.hand brakes should be provided to lock the wheelchair at desired location.foot pressextended base with molded plastic for better grip.anti rust chrome finsh. safe work load of100 kg , basin stand type i ht 850 mm ss bowl ms tubular frame of dia 25.4 x1.2 mm tube work mounted on three 50 dia.non rusting castors all without brack. ss part finished with matt polish , kick buckettype i overa all dimension of the bucket should be 517 mm ( l ) x 517 mm ( w ) x 210 mm h.it should made of 12.7 mm dia and 1.6 mm thick ss 304 ring. the bowl should be ss made of .8 mm thck .3 nos 50 mm diahigh endurance plasticinjection moulded castors should be provided for the movement.mx load bearing capacity should be 10 kg. , hospital curtain tracks & i.v. tree system supply installation testing & commissioning of cubical tracks system made of powder coated aluminium alloy, stain free polyster fabric , water repellent curtains , smooth movement , non sticking runnner with stainless steel hooks made from mirror finish stainless steel , adjustable height with all accessories. total quantity : 1...

Health And Family Welfare Department - Bihar

30243928 bids are invited for pile20.2.3 boring, providing and installing bored cast in situ reinforced cement concrete piles of grade m 25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement butincluding the cost of boring, with bentonite solution andtemporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavatedearth with all lifts and leads ( length of pile for payment shall be measured upto bottom of pile cap ) .450mm dia piles ( inclusive of carriage ) , pcc4.1.5 providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering all work up to plinthlevel : 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) ( inclusive of carriage ) , rcc providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana / ordinary portland / portland slag cement, admixtures in recommended proportion as per is: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer in charge; for the following grades of concrete. note: extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. in case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re design the mix or bear the cost of extra cement. ( inclusive of carriage ) , brick work brick work with bricks of class designation 100a in foundations and plinthin :cement mortar 1:4 ( 1 cement : 4 coarse sand ) ( inclusive of carriage ) , sand filing supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ( inclusive of carriage ) with lead upto 3 km , shuttering centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete , reinforcement steel steel reinforcement for r.c.c. work ready to use cut and bend rebars of approved make from factory / workshop to construction site including placing in position and binding all complete thermo mechanically treated bars of grade fe 500d or more. , plinth protection making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand ( zone iii ) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources ) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. , door & window providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. ( glazing, paneling and dash fasteners to be paid for separately ) :powder coated aluminium ( minimum thickness of powder coating 50 micron ) , glass providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . ( cost of aluminium snap beading shall be paid in basic item ) :with float glass panes of 5 mm thickness ( weight not less than 12.50 kg / sqm ) , door closer providing and fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm ) , with necessary accessories and screws etc. complete. , door providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including stainless steel butt hinges wirhnecessary screws , door stopper providing and fixing aluminium hanging floor door stopper, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour and shade, with necessary screws etc. complete. single rubber stopper , solling providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as perbuilding specification and direction of e / l, , tile 111.41a.3.1 providing and laying vitrified tiles in floor in different sizes { thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 ( 1 cement: 4 coarse sand ) jointing with grey cement slurry @3.3 kg / sqm including grouting the joints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only.laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.glazed vitrified tiles matt / antiskid finish of size size of tile 600x600 mm , tile 2 providing and laying ceramic glazed floor tiles of size 300x300 mm ( thickness to be specified by the manufacturer ) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigment etc., complete. , tile 3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. , granite providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand ) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge : flamed finish granite stone slab jet black, cherry red, elite brown, cat eye or equivalent. , false ceiling providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ? 85%, thermal conductivity k = 0.052 0.057 w / m k, fire performance as per ( bs 476 pt 6 &7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mm thick ( galvanized @120 gsm ) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel itemgalvanised @80gsm ) 50 mm long 8mm outer diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’. the system should rest on periphery walls / partitions with the help of gi perimeter wall angle of size24x24x3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall s.s. screws. the exposed bottom portion of all t sections used in false ceiling support system shall be pre painted with polyester baked paint, for all heights. the work shall be carried out as per specifications, drawings and as per directions of the engineer in charge. with 16 mm thick beveled tegular mineral fibre antimicrobial false ceiling tile confirming to iso 5 ( class 100 ) specifications , pre fabsteel designing, providing, installing and fixing factory finished custom designed cold form light gauge steel framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. the steel sheet shall be galvanized ( az 150gms aluminium zinc alloy coated steel having minimum yield strength 300 550 mpa ) conforming to aisi specifications and ibc 2009 for cold formed steel framing and construction and also as per is: 875 1987, iso 800 1984 and is:801 1975.the frames shall be fixed to rcc slab or tie beam over neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to aisi 304 and 316 at 500mm c / c with minimum embedment of 100mm in rcc ( rcc to be paid separately ) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. the item also includes the submission of stability reports dulyexamined and issued by any nit / iit. the rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above. , pre fabwall providing and fixing of external wall system on light gauge steel frame work with outer face cement boards as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make. a groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. the board shall be fixed in a staggered pattern. internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately ) outer face: outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, type a, as per is:14862:2000 ( high pressure steam cured ) inner face : 12.5 mm thick gypsum plaster board conforming to is 2095:2011 fixed on 8 mm thick fibre cement board confirming to is:14862:2000 of type b ( high pressure steam cured ) , pre fabin. wall providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c / c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. ( cost of frame work to be paid for separately , roof sheet supply & installation of precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55mm ) with epdm seal or with polymer coated j or l hooks, bolts and nuts 8mm diameter with bitumen and g.i. limpet washers or with g.i. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. , ridge plain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : ridges plain ( 500 600mm ) . , gutter drain providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + / 5% total coated thickness ( tct ) thick zinc coating 120gsm as per is: 277 in 240mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumen washers complete : gutter , flashing providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 5% total coated thickness ( tct ) , zinc coating 120gsm as per is: 277 in 240mpasteel grade, 5 7 microns epoxy primer on both side of the sheet and polyester topcoat 15 18 microns using self drilling / self tapping screws or with polymer coated j or l hooks, bolts and nuts and or g.i. seam bolts and nuts, g.i. plain and bitumenwashers complete :flashings / aprons. ( upto 600 mm ) , under deck insulation providing and fixing thermal insulation of ceiling ( under deck insulation ) with resin bonded rockwool conforming to is: 8183, density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to ceiling with metallic cleats ( 50x50x3 mm ) @ 60 cm and wire mesh of 12.5mm x 24 gauge wire mesh, for top most ceiling of building. , resin bonded rock wool providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg / m3, 50 mm thick, wrapped in 200 g virgin polythene bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineerin charge. , putty providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , distemper distempering with dry distemper of approved brand and manufacture ( two or more coats ) and of required shade on new work , over and including priming coat of whiting to give an even shade. , ex. paint finishing walls with acrylic smooth exterior paint of required shade : new work ( two or more coat applied @ 1.67 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) , oil paint painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coats on new work . , steel steel work in built up tubular ( round, square or rectangular hollow tubes etc. ) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. hot finished welded type tubes , excavation earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan ) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. , paver block providing and laying 60 mm thick factory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thickcompacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of engineer in charge. , phe 4 providing and fixing mirror of superior glass ( of approved quality ) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: rectangular shape 453x357 mm , phe 5 providing and fixing toilet paper holder:c.p. brass , phe 6 providing and fixing water closet squatting pan ( indian type w.c.pan ) with 100 mm sand cast iron p or s trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white p.v.c. flushing cistern, including flush pipe, with manually controlleddevice ( handle lever ) conforming to is : 7231, with all fittings and floors wherever required :white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests , phe 7 providing and fixing white vitreous china pedestal type water closet ( european type w.c. pan ) with seat and lid, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) , conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : w.c. pan with isi marked white solid plastic seat and lid , phe 8 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto 1 metre long with s.s. triangular plate to eureopean type w.c. of quality and make as approved by engineer in charge , phe 11 providing and fixing c.p. brass long body bib cock of approved quality conforming to is standards and weighing not less than 690 gms.15mm nominal bore , phe 12 providing and fixing c.p. brass bib cock of approved quality confirming to is:893115mm nominal bore , phe 13 providing and fixing c.p.brass angle valve for basin mixer and geyser points of approved quality conforming to is 8931 a ) 15 mm nominal bore.15 mm nominal bore , phe 14 providing and fixing wash bashin with c.i. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china surgeon type wash basin of size660x460 mm with a pair of 15 mm c.p. brass pillar taps with elbow operated levers , phe 19 providing and fixing cp brass shower rose with 15 or 20 mm inlet100 mm diameter , phe 20 providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. , phe 22 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 40 mm dia, nominal bore , phe 23 providing and fixing g.i. pipes complete with gi fittings and clamps including cutting and making good the walls etc. ( internal work ) 50 mm dia, nominal bore , phe 25 p / f m.s. cap 100 mm dia , phe 26 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.75 mm dia pipe , phe 27 providing and fixing, upvcpipes 6 kg / cm2 ( is: 4985 ) including all fittings ( plain or door ) e.g. bends, junction, offsets, access pieces, jointing with rubber ring / solvent cement joints includingrequired suports, cutting chase or holes in walls and floors and making good where required.110 mm dia pipe , phe 28 providing & fixing on wall face unplasticised rigid pvc rain water pipes conforming to is:13592 tyape a included jointing with seal ring conforning to is:5382 leaving 10 mm gap for thermal expansion. ( i ) single socketed pipes.110 mm diameter , phe 29 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. coupler 110 mm diameter , phe 30 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. bend 87.5 deg 110 mm diameter , phe 31 providing, fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is ; 13592 type a including jointing with seal ring conforming to is ; 5382 leaving 10 mm gap for thermal expansion. shoe 110mm shoe , phe 32 providing & fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .m.s. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1cement : 4 coarse sand ) and making good the wall etc. complete.110 mm dia , phe 33 providing and fixing cpvc pipes having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 20 mm nominal outer dia pipes , phe 34 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 25mm dia, nominal bore , phe 35 providing and fixing of gun metal gate valve with ci wheel of approved quality ( screwed ends ) 32 mm dia, nominal bore , phe 36 providing and fixing gun metal non return valve of approved quality ( pn 1.6 ) 40 nominal bore , phe 37 providing and fixing brass stop cock of approved quality15mm nominal bore , ex. phe 6 providing 250mm wide brick drain in cement mortar ( 1:6 ) with av. 150mm. clear depth and 250mm apron including cost of e / w. involved with 75mm cement concrete ( 1:4:8 ) over one brick designation 100 a flat soling in proper grade and slope at the base.the drain duly.plastered in cm. ( 1:3 ) with punning over exposed surface all complete as per buildingspecification and direction of e / l, , ex. phe 7 excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil ( hard or soft ) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [ hard / dense soil ] pipes, cables etc.exceeding 80mm dia.but not exceeding 300mm dia. , ex. phe 9 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 250 mm dia rcc pipe , ex. phe 10 providing and laying non pressure np2 class ( light duty ) rcc pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand ) including testing of joints etc. complete. ( for storm drainage ) 300 mm dia rcc pipe , ex. phe 15 constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement: 4 coarse sand ) for sluice valve, with c.i. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside ) with channel lid and rcc top slab 1:2:4 mix ( 1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand ) 12 mm thick finished with a floating coat of neat cement complete as per standard design:with f.p.s. bricks , fire extinguisher 2 providing and fixing abc powder type fire extinguishers consisting of welded m.s. cylindericalbody, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to is:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.capacity 4.5 kg. , electrical 2 wiring for twin control light point with 1.5 sq.mm frls pvcinsulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc. as required. , electrical 3 wiring for group controlled ( looped ) light point / fan point / exhaust fan point / call bell point ( without independent switch etc. ) with 1.5 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq. mm frls pvc insulatedcopper conductor single core cable etc. as required. group c , wiring frls pvc insulated copper conductor 1 2 x 2.5 sq. mm. + 1 x 2.5 sq. mm. earth wire , wiring frls pvc insulated copper conductor 2 2 x 4 sq.mm. + 1 x 4 sq.mm. earth wire , wiring frls pvc insulated copper conductor 3 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire , wiring frls pvc insulated copper conductor 4 4 x 16 sq. mm + 2 x 16 sq. mm earth wire , s / f, gi box along with modular base & cover plate 1 1 or 2 module ( 75mm x 75mm ) , s / f, gi box along with modular base & cover plate 2 3 module ( 100mm x 75mm ) , s / f, gi box along with modular base & cover plate 3 4 module ( 125mmx75mm ) , s / f, gi box along with modular base & cover plate 4 6 module ( 200mm x 75mm ) , s / f, gi box along with modular base & cover plate 5 12 module ( 200mmx150mm ) , s / f modular switch / socket on the existing modular plate 6 5 / 6 amps switch , s / f modular switch / socket on the existing modular plate 7 15 / 16 amp switch , s / f modular switch / socket on the existing modular plate 8 3 pin 5 / 6 amp socket outlet , s / f modular switch / socket on the existing modular plate 9 6 pin 15 / 16 amp socket outlet , s / f modular switch / socket on the existing modular plate 10 bell push , electrical 7 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. , electrical 8 providing and fixing m.s. fan clamp type i or ii of 16 mm dia m.s. bar, bent to shape with hooked ends in r.c.c. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete as required. , electrical 10 supplying and fixing 20 a, 240 v, spn industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 a c curve, sp, mcb, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. , electrical 13 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 8 way , double door , 40 a, rccb supplying and fixing following rating, double pole, ( single phase and neutral ) , 240 v, residual current circuit breaker ( rccb ) , having a sensitivity current 30 ma in the existing mcb db complete with connections, testing and commissioning etc. as required. , 40a mcb supplying and fixing 40 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 40 tp mcb , single pole mcb supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. , earthing 1 earthing with g.i. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required. , earthing 2 providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. , earthing 3 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. , fiting & fixtures 1 supply and installation of regular / standard model a.c. ceiling fan of 1400 mm sweep including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm fr pvc insulated copper conductor etc as required. , fiting & fixtures 2 supplying and fixing single wall mounted 18 / 22 watt led type batten fitting complete with electronic driver and led tube etc directly on wall / ceiling includingconnections with 1.5 sq.mm fr pvc insulated copper conductor and earthing the body etc. as required. , fiting & fixtures 3 supply installation and comissioning ofintegrated batten made ( 2ft ) of ultra slim co extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.white finish abs end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. these end caps are snap fitted to the fixture.high efficiency long life led with lumen efficacy of 130 lm / w with viewing angle of 120º.powered by an integral isolated low thd electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection.can be fixed directly into the wall / ceiling by means of mounting ss clips provided with the fixture. ip 20, lumen output of 950 lumens with system efficacy of > 105lm / w .cri >80, color temperature 6500k, thd <20% and pf>0.95, ip20 . life class of 35, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source. cat ref havells :lumilinebs9wled840spcwh or approved equivalent. , fiting & fixtures 5 supplying and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceilingincluding connection with 1.5 sq.mm fr pvc insulated copper conductor cable and earthing the body etc. as required. , fiting & fixtures 7 supply installation and comissioning of 28w 2x2 panel recess mounting luminaire with high performance leds, suitable for mounting with armstrong / grid ceiling.crca powder coated white after phosphochromate treatment.high efficiency long life led package in integral module with lumen efficacy of >100 lm / w and viewing angle of 120° to ensure better uniformity.powered by an independent isolated, selv output electronic led driver ( smps based constant current supply ) with output short circuit protection, surge protection & other reliability test. lumen output of 3450 lumens.cri >80, color temperature 5700k, thd <10% and pf >0.95, ip20, ik03.life class of 50, 000 hrs @ l70, operating temperature: 10 to +45 deg.c; input supply voltage range:140 270 v, frequency :50 60 hz;internal surge protection:3 kv; protection including 3 core 1.5 sq.mm frls pvc insulated and pvc sheathed copper conductor cable and earthing etc. up to suitable point complete as required. : reverse polarity, open & short circuit. driver safety requirement standards :is 15885 2 13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source.cat ref havells :venusneohe2x2plr128wled857 or approved equivalent. , signage 4 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge , wall projected 250x210mm, both sides , signage 5 providing and fixing of signages modular curved frame technology of various widths and lengths to fometre suggested usages made of aluminium extruded sections. duly anodised all signages shall be provided with 0.6 0.8mm polycarbonate protecting film over the prints of appropriate size .all complete as per direction by engineer in charge, door mounted, 300x80mm , hospital sheet patient bedtype iii with mattress overall sizes: ( l ) 1900 mm x ( w ) 900 mm x ( h ) 600 mmdescription: sheet bed should be a plain bed used in the recovery ward.material specifications: under structure has a higher diameter tubewhich should provide a sturdy understructure.lying surface area of crcafinish specifications: head board / leg board should be made of frame ms erw roundtube of sections ø19, ø25.4& ø31.75mm, ofthickness1.6 mmprovision for mounting of iv pole and mosquito net pole should be presentfinish specifications: powder coating should be bacteriostatic and thermosetting epoxy polyester, formulated to fulfill the requirements for bacterial protection.all powder coated parts in ral whiteperformance specifications: maximum patient load should be 135 kgthickness mattress: 3+sand