Bihar State Building Construction Corporation Limited - Bihar

44867788 estimate of iti mahnar type4 phase 2 ( centre of excellence ) 1 23.12 clearing grass and removal of the rubbish up to distance 50m outside the periphery 2 2.6 earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed. 3 2.18.2 closed timbering over area depth exceeding 1.5m apart 4 2.27 extra for every additional lift of 1.5 m or part thereof in : 2.27.1 all kinds of soil 5 2.25a excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.if local earth is available at more than 3 km lead the actual lead mustbe approved by compitent authority. cairraiage of material will be paidseperately and calculated after deducting initial lead. 6 2.26 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead 7 2.28 supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 8 2.37.3 treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm diameter holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existingfloor. 2.37.3.1 with chlorpyriphos ec 20% with 1% concentration 9 11.72 providing designation 100 a one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of e/l, 10 4.1 providing and laying in position cement concrete of specified grade. 4.1.2 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 4.1.3 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 11 16.75 providing and laying c.c. pavement of mix m 25 with ready mixedconcrete from batching plant. the ready mixed concrete shall be laidand finished with screed board vibrator , vacuum dewateringprocess and finally finished by floating, brooming with wire brush etc.complete as per specifications and directions of engineer incharge. (the panel shuttering work shall be paid for separately).(note: cement content considered in this item is @ 330 kg/cum.excess/less cement used as per design mix is payable/ recoverableseparately) 12 5.33 providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana /ordinary portland /portland slag cement 5.33.1.1 all work upto plinth level : concrete of m 25 grade with minimum cement content of 330 kg/cum 13 5.33.2.1 all work above plinth level upto floor v level. : concrete of m 25 grade with minimum cement content of 330 kg/cum 14 5.22 reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete. 5.22.1a tmtc 500 08 mm dia. 5.22.1b tmtc 500 10 mm dia. 5.22.1c tmtc 500 12 mm dia. 5.22.1d tmtc 500 16 mm dia. 5.22.1e tmtc 500 20 mm dia. 15 5.9 centring and shuttering including strutting, propping etc. and removal 5.9.1 foundations, footings, bases of columns etc. for mass concrete. 16 5.9.3 suspended floors, roofs, landings, balcnies and access platform. 17 5.9.16.1 edges of slabs and breaks in floors and walls : under 20 cm wide 18 5.9.5 lintels, beams, plinth bams, griders, bressumers and contilevers. 19 5.9.6 columns,pillars, piers, abutments, posts and struts 20 5.9.7 stairs,(excluding landings) except spiral staircaces. 21 5.9.19 weather shade,chajjas, corbels etc. including edges 22 6.1a brick work with 100a bricks as per is 12894(2002) & is 3495 in foundations and plinth in : 6.1.14a cement mortar 1 .:6 (1 cement: 6 coarse sand ) 23 6.1c brick work with fly ash bricks as per is 12894(2002) & is 3495 in foundations and plinth in : 6.1.14c cement mortar 1 .:6 (1 cement: 6 coarse sand ) 24 6.1c brick work with fly ash bricks as per is 12894(2002) & is 3495 in foundations and plinth in 6.1.14c+ 6.3c cement mortar 1 .:6 (1 cement: 6 coarse sand ) : extra tor brick work in superstructure above plinth level upto floor v cum 25 6.1.12c brick work with fly ash bricks as per is 12894(2002) & is 3495 in foundations and plinth in cement mortar 1.:4 (1 cement: 4 coarse sand ) 26 11.41. providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorptions less than 0.08 % and conforming to is : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete. 11.41.2 size of tile 60x60 cm 27 4.17 making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. 28 6.47a providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. clear depth and 250mm apron including cost of e/w. involved with 75mm cement concrete 29 13.24 6 mm cement plaster to ceiling of mix : 13.24.2 1:4(1 cement: 4 coarse sand) 30 13.11.4 12 mm cement plaster on rough side of single or half brick wall of mix : (1 : 6) 31 13.12.3 15 mm cement plaster on rough side of single or half brick wall ofmix 32 13.17.2 12 mm cement plaster 1:4( 1 cement: 4coarse sand) finished with afloating coat of near cement details of cost for 10 sqm 33 13.80a.2 providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 34 13.92 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: 35 13.46.1 finishing walls with acrylic smooth exterior paint of required shade : new work (two or more coat applied @ 1.67 ltr/ 10 sqm over and including priming coat of exterior primer applied 36 26.41 the frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. all self drilling tapping screws for joining the members shall have atypeii coating in accordance with astmb633(13)or equivalent corrosion protection of gauge10&12,tpi 16&8 of length 20mm.the frames shall be fixed to rcc slab or tie beam over neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and121mm length conforming to aisi304 and 316 at 500 mmc/c with minimum embedment of100mm in rcc(rcc to be paid separately) and located not more than300mm from corners or termination of bottom tracks complete in all respects. the item also includes the submission of stability reports duly examined and issued by any nit/iit. the rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above 37 ar system details: providing and laying 3mm thick self levelling epoxy flooring (of approved shade) over trimix/well finished/levelled vdf floor.. ø  physical properties of nitoflor eu 5 @ 35ºc ø  pot life: 70 minutes, mixed density: 1.80 1.85 g/cc, compressive strength (bs 6319 part 2, 1983): 60 n/mm2 @ 7 days, tensile strength (bs 6319 part 7, 1983): 12 n/mm2 @ 7 days, flexural strength (bs 6319 part 3, 1983): 25 n/mm2 @ 7 days, water absorption (bs 1881 part 122, 1983): nil, curing characteristics @ 35ºc, initial hardness: 16 hours, full cure: 7 days, adhesion: greater than the tensile strength of concrete.  physical properties of nitoflor sl 1000: i) pot life @ 27 ºc ii)nitoflor sl1000: 30 min, nitoprime 25: 2 3 hours cure time iii)foot traffic: 24 hours, vehicular traffic: 48 hours, chemical resistance: 7 days iv) mixed density: 1.70 g/cc, compressive strength @7 days (bs 6319): > 50 n/mm2, flexural strength @7 days (bs 6319): > 25 n/mm2, tensile strength @7 days (bs 6319: > 12 n/mm2, abrasion resistance: 0.1mg/ cycle loss of (astm d 4060) weight (with cs 17 wheel of 1000g weight), shore d hardness as per (astm d 2240): >75, adhesion strength: > 1.5n/mm2 @ 7 days (astm d4541) ø application methodology: the prevailing relative humidity should not exceed 75% at any stage of the application. ambient temperature at the time of application 20°c 30°c 40°c. max elapsed time for light spiked rolling from time of final trowel 30 – 60 mins 20 – 30 mins 10 – 20 mins ø surface preparation: • new concrete, or cementitious substrates, should be at least 28 days old and have a moisture content not exceeding 5% (rh <75%).• the substrate should be clean, sound and free from contamination such as mortar and paint splashes curing compounds, oil and grease. excess laitance deposits are best removed by light mechanical scabbling, grinding or grit/captive blasting followed by vacuum cleaning to remove dust debris. all preparation equipment should be of a type approved by fosroc.• all blowholes and other surface undulations greater than 1 mm in depth should be repaired with a proprietary, repair compound consult the local fosroc office for specific recommendations.• oil and grease contamination must be completely removed by grinding down to sound, clean concrete. alternatively, captive/grit blasting techniques can be used to provide the required substrate.• where these methods are considered impracticable, alternative methods may be considered but a clean, sound and dry substrate must still result. in particular it is essential that the substrate does not suffer from conditions of rising damp. fosroc must approve any alternative preparations prior to commencement of work, as fosroc will not accept responsibility under any other condition. • isolation joint treatment: nitoseal pu50 single component, non sag, medium modulus, moisture cure, polyurethane hybrid joint sealant having properties shore a hardness 32, average peel strength 220n,elastic cover of 80% as per guidelines of en iso 7389, maf up to 50%. coving: providing & applying coving of size 75mmx75mm at wall & floor junctions after application of nitoprime 25 using nitoflor tf30 having compressive strength as per (bs6319 part 2) 75 n/mm2 flexural strength as per (bs6319 part 3) 26 n/mm2 tensile strength as per (bs6319 part 7) 13.5 n/mm2, abrasion resistance 3.0 mg/cycle bond strength to concrete 3.0 n/mm2.coving has to be coated with nitoflor fc150 high build, solvent free epoxy resin floor coating. priming: apply epoxy resin primer nitoprime 25 after mixing the base and hardener mechanical using a slow speed heavy duty drilling machine (300 400 rpm) fitted with a suitable paddle to achieve homogeneous mix and apply to prepared surface at a coverage rate of 5.5 to 6.5 sqm/lit. ø application of nitoflor eu5 (2mm): • nitoflor sl1000 flooring is supplied in four pre weighed packs (base, hardener, aggregate & colour pack) which are ready for immediate on site use. part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor and would furthermore automatically invalidate fosroc’s standard product guarantee.• mixing should be carried out using either a forced action mixer; or a heavy duty, slow speed drill with proprietary mixing paddle attachment. fosroc should of a type and capacity approve all such equipment. the components should be mixed in a suitably sized mixing vessel.• add the entire contents of the colour pack into the base pack and mix for 15 30 seconds, until homogeneous.• empty the hardener pack into the mix of base and colour pack and mix until an even texture and colour is obtained.• thereafter, the contents of the graded aggregate pack should be slowly added and mixing carried out for a further 3 minutes until completely homogenous material is obtained.• application of nitoflor eu5 (laying):• the applicator should ensure that there are sufficient supplies of plant, labour and materials to make the mixing and subsequent application process a continuous one for any given, independent floor area.• once mixed, the material must be used within its specified pot life see ‘properties’ section of the relevant data sheet.• the material should be spread to a uniform thickness across the floor area using a squeegee or a notched trowel.• overcoating:• nitoflor eu5 will be ready for overcoating, using nitoflor sl 1000, after 48 hours from completion of application.  application of nitoflor sl 1000 (1mm): • mixing nitoflor sl 1000: • nitoflor sl1000 flooring is supplied in four pre weighed packs (base, hardener, aggregate & colour pack) which are ready for immediate on site use. part mixing of these components is not acceptable and will affect both performance and appearance of the finished floor and would furthermore automatically invalidate fosroc’s standard product guarantee. • mixing should be carried out using either a forced action mixer; or a heavy duty, slow speed drill with proprietary mixing paddle attachment. fosroc should of a type and capacity approve all such equipment. the components should be mixed in a suitably sized mixing vessel. • add the entire contents of the colour pack into the base pack and mix for 15 30 seconds, until homogeneous. • empty the hardener pack into the mix of base and colour pack and mix until an even texture and colour is obtained. • thereafter, the contents of the graded aggregate pack should be slowly added and mixing carried out for a further 3 minutes until completely homogenous material is obtained • application (laying): • the applicator should ensure that there are sufficient supplies of plant, • once mixed, the material must be used within its specified pot life see “properties” section of the data sheet.labour and materials to make the mixing and subsequent application process a continuous one for any given, independent floor area. • the material should be poured onto the prepared and primed substrate as soon as mixing is complete. it should be spread to the required thickness using a serrated trowel; with care taken not to overwork the resin, spreading evenly and slowly. • immediately after laying, the material should be rolled, using a spiked nylon roller, to remove slight trowel marks, and to assist air release. the rolling should be carried out using a ‘back and forth’ technique along the same path. an overlap of 50% with adjacent paths is recommended. • further light rolling may be required to remove surface imperfections, or for subsequent release of trapped air, but should be carried out in accordance with the maximum times given below: note: any chemical/ product specified above of equivalent quality can be used. final finishing of floor must be as per the direction of engineer in charge. 38 26.43 providing and fixing internal wall panels on light gauge steel frame work with 12.5mm thick gypsum plaster board conforming is 2095:2011 fixed on cement board as per standard sizes fixed with self drilling / taping screws / fasteners @ 60cm c/c of approved make, screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm. proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately 26.43.1 cement fiber board 8 mm thick as per is 14862:2000 of type b (high pressure steam cured) 39 26.44 providing and fixing in all exterior face panels breathable vapour barrier underneath the cement fiber board as per national building code 2009 complete as per direction of engineer in charge. 40 12.62 x providing and fixing thermal insulation with resin bonded rock wool conforming to is: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 g virgin polythene bags fixed to wall wirh screw, rawel plug & washers and held and in position by criss cossing gi wire etc. complete as per directions of engineer in charge. 41 26.22 providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595x595mm of approved texture, design and patterns as per cpwd specification 2019, to be laid in true horizontal level suspended on inter locking metal t grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main t runners of size 24x38 mm of length 3000 mm,cross t of size 24x32 mm of length 1200 mm and secondaryintermediate cross t of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and l shape level adjuster of size 76x25x25x1.6 mm fixed with grid and z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require,fixed with glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall s.s screws. the workshall be carried out as per specifications, drawing and as per directionsof the engineer in charge. 26.22.1 with 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. 42 ar supplying and fixing rolling shuters of approved make. madeof required size of gi sheets interlocked together through theirentire length and jointed together at the end by end locksmounted on specially designed pipe shaft with brackets, sideguides and arragements for inside and outside locking withpush and pull operation complete including the cost ofproviding and fixing necessary 27.5cm long wire springsmanufactured from high tensile steel wire of adequatestrength conforming to is:4454 part1 and gi top cover ofrequired thickness for rolling shutters including providing andfixing ball bearing for rolling shutters ...

Bihar Industrial Area Development Authority - Bihar

42999173 request for proposal ( rfp ) for selection of firm / agency / supplier for supply, installation, testing and commissioning of different machines including civil, electrical and other fixtures for setting up food testing lab in upendra maharathi shilp anusandhan sansthan, patna, bihar. list of proposed equipment – chemical 1 highly sensitive triple quadrupole lcms / ms system 2 gas chromatographs with ecd, fid, fpd detector, with headspace and auto sampler ( auto sampler to be provided ) with 5 years consumable and warranty extended upto 5 years 3 gc ms ms with ecd, fid, fpd detector, with headspace and auto sampler ( auto sampler to be provided ) with 5 years consumable and warranty extended upto 5 years 4 icpms accessories and microwave digestion system 5 double beam atomic absorption spectrophotometer 6 high performance liquid chromatography ( gradient ) with uv and fld detector, auto sampler & essential columns with accessories with 5 years consumable and warranty extended upto 5 years 7 uv vis spectrophotometer 8 centrifuge with 5 years consumable and warranty extended upto 5 years 9 ultra low temperature 80 ult freezer 10 ph meter with 5 years consumable and warranty extended upto 5 years 11 elisa reader, filter based plate reader with 5 years consumable and warranty extended upto 5 years 12 heating mantles with 5 years consumable and warranty extended upto 5 years 13 laboratory precision oven uniform temperature 300 o c with 5 years consumable and warranty extended upto 5 years 14 cyclotec lab grinding millwith 5 years consumable and warranty extended upto 5 years 15 magnetic stirrer with 5 years consumable and warranty extended upto 5 years 16 magnetic stirrer with hotplate with 5 years consumable and warranty extended upto 5 years 17 block digestor for eight samples with 5 years consumable and warranty extended upto 5 years 18 moisture analyzer with 5 years consumable and warranty extended upto 5 years 19 muffle furnace 930 degree c with 5 years consumable and warranty extended upto 5 years 20 rectangular hot plate with 5 years consumable and warranty extended upto 5 years 21 refrigerated microcentrifuge with 5 years consumable and warranty extended upto 5 years 22 refrigerators, 2 to 8degreec, capacity 1000l with smart view with 5 years consumable and warranty extended upto 5 years 23 refrigerated incubator orbital shaker ( stackable ) with 5 years consumable and warranty extended upto 5 years 24 soxhlet extraction unit with 5 years consumable and warranty extended upto 5 years 25 nitrogen concentrator ( turbo vap. concentrator ) with 5 years consumable and warranty extended upto 5 years 26 solid phase extraction manifold with 5 years consumable and warranty extended upto 5 years 27 vaccum fitration apparatus along with vaccum pump with 5 years consumable and warranty extended upto 5 years 28 multi tube vortex with mixing, heating, and cooling functions with 5 years consumable and warranty extended upto 5 years 29 analytical weight box, e2 with 5 years consumable and warranty extended upto 5 years 30 analytical weight box, e2, with 5 years consumable and warranty extended upto 5 years 31 analytical balance, 220g x 0.1mg with internal calibration with 5 years consumable and warranty extended upto 5 years 32 microbalance, 5.2g x 0.001mg with internal calibration and static eliminator with 5 years consumable and warranty extended upto 5 years 33 precision balance, 6200g x 0.1 with external calibration with 5 years consumable and warranty extended upto 5 years 34 micro pipette, 30 300 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 35 micropipette, 1 to 10 ml, eppendorf with 5 years consumable and warranty extended upto 5 years 36 micro pipette, 2 to 20 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 37 micro pipette, 10 to 100 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 38 micro pipette, 20 to 200 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 39 micro pipette, 100 to 1000 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 40 rotary vacuum evaporator along with heating bath, diaphragm pump, interface and recirculating chiller rotary evaporator and heating bath with 5 years consumable and warranty extended upto 5 years 41 digital stop watch list of proposed equipment – biological 1 real time pcr system with 5 years consumable and warranty extended upto 5 years 2 b.o.d cooling incubators with 5 years consumable and warranty extended upto 5 years 3 vertical laboratory autoclave ( radial locking ) with 5 years consumable and warranty extended upto 5 years 4 laboratory precision oven uniform temperature 300 o c with 5 years consumable and warranty extended upto 5 years 5 horizontal laminar air flow with 5 years consumable and warranty extended upto 5 years 6 digital top pan balance ( 20 gm 800 gm ) , with 5 years consumable and warranty extended up to 5 years 7 analytical balance ( 0.01mg 20 gm ) , with 5 years consumable and warranty extended upto 5 years 8 stability chamber with 5 years consumable and warranty extended upto 5 years 9 biosafety cabinet type ii b, with 5 years consumable and warranty extended upto 5 years 10 deep freezer 20°c, with 5 years consumable and warranty extended upto 5 years olsc 119 12 11 stomacher, with 5 years consumable and warranty extended upto 5 years 12 homogenizer / lab stirrer, with 5 years consumable and warranty extended upto 5 years outer & inner ss 13 ph meter, with 5 years consumable and warranty extended upto 5 years 14 lab grinding mill ( homogenizer ) with 5 years consumable and warranty extended upto 5 years olsc ls 01 15 vortex mixer, with 5 years consumable and warranty extended upto 5 years 16 refrigerated microcentrifuge with 5 years consumable and warranty extended upto 5 years 17 non refrigerated microcentrifuge with 5 years consumable and warranty extended upto 5 years 18 gel documentation system with printer, with 5 years consumable and warranty extended upto 5 years 19 biosafety cabinet type ii b, with 5 years consumable and warranty extended upto 5 years 20 sonicator, with 5 years consumable and warranty extended upto 5 years 21 binocular microscope / 3d microscope, with 5 years consumable and warranty extended upto 5 years 22 uv cabinet, with 5 years consumable and warranty extended upto 5 years 23 serological water bath, with 5 years consumable and warranty extended upto 5 years 24 electronic colony counter with 5 years consumable and warranty extended upto 5 years proposed cost for furniture and fixture for setting up of testing lab, dept. of industries 1 wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit, with modular type switch, modular plate, suitable size g.i. box and earthing the point with 1.5 sq.mm. fr pvc insulated copper conductor single core cable etc.as required group c 2 wiring for light / power plug with 2x4 sq.mm fr pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit along with 1 no 4 sq.mm. fr pvc insulated copper conductor single core cable for loop earthing as required. 3 wiring for circuit / submain wiring along with earth wire with the following sizes of fr pvc insulated copper conductor, single core cable in surface / recessed pvc conduit as required. 2x2.5 sq.mm +1x2.5 sq.mm 2 x 6 sq.mm + 1 x 6 sq.mm. earth wire 2 x 10 sq.mm. + 1 x 10 sq.mm. earth wire 4 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 4 x 6 sq. mm + 1 x 6 sq. mm earth wire 4 x 10 sq. mm + 1 x 10 sq. mm earth wire 4 x 16 sq. mm + 1 x 16 sq. mm earth wire 4 supplying and fixing pvc / g.i box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required ( adopter box above each d.b ) . 5 supplying and fixing suitable gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pinm 5 / 6 and 15 / 16 amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc. as required. ( for power plug ) 6 supplying and fixing suitable size g.i box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5 / 6 amps modular socket outlet and 5 / 6 amps modular type switch, connection, painting etc., as required. ( for light plugs to be used in non residential buildings ) 7 supply & fixing 8 way double door sp & n, sheet steel, mcb distribution board, 240 volts, on surface / in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required ( but without mcb / rccb / isolator ) lighting db ( a ) 40 amps double pole mcb isolator : 1 no. ( b ) outgoing 6 / 32 amps sp mcb ( b series ) :6 nos. 8 supply & fixing 4 way ( 4+12 ) double door tp & n, sheet steel, mcb distribution board, 415 volts, on surface / in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required ( but without mcb / rccb / isolator ) power db ( a ) 63 amps double pole mcb isolator : 1 no. 9 ( b ) outgoing 16 / 32 amps sp mcb ( c series ) : 12 nos. s / f following modular type switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc as required. 10 tv antenna socket outlet 11 s / f electronics musical call bell suitable for d.c / a.c. single phase 230 copmplete as required. 12 supplying and fixing batten / angle holder incluiding connection etc as required. 13 supplying and fixing 2 pin, 5 amp, celling rose on the existing junction box / pvc box incluiding connection etc as required. 14 s / f modular blanking plate on the existing modular plate and switch box excluding modular plate as required. 15 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. electrical fixture fitting 16 supply and installation of 300 mm 230volt ac exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required. 17 supply & installation 400 mm dia 230 volt ac wall / cabin fan including fixing the bracket making connection testing commissioning etc as required. 18 supply and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver directly on false ceiling including connection with 1.5 sq mm fr insulated copper conductor cable and earthing the body etc as required 19 supplying and fixing indoor recess mounting 36 watt led flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. directly on false ceiling including connection with 1.5 sqmm fr pvc insulated copper conductor cable and earthing the body etc as required. 20 supplying and fixing of following types lamp in the existing electrical fitting / fixtures etc. as required. 10 / 12 watt led lamp 21 supplying and fixing 90 watt led type street light with die cast aluminium housing for ingress protection of ip65 and complete with all accessories etc, on pole / building including connection with fr pvc insulated copper conductor cable and earthing the body etc. as required. 22 supplying and fixing following sizes of pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. section 4: fire extinguishers p / f with brackets wall mounted fire extinguishers as per details below: 23 abc power type ( stored pressure ) fire extinuisher 4 kg .capacity , isimark ( is: 15683 ) squeeze gripe valve, operating temperature ( +5 deg. to ( +55 ) deg.for class 3a type of fire with abc powder , complete in all respect. 24 co2 type fire extinguisher 4.5kg capacity isi mark ( is : 15683 ) squeeze grip value , operating temperature ( 30deg. to 55deg.foe class 13b type of fire fitted with 1mt.hose & pvc hoen, complete in all respect. earthing 25 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. 26 providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. 27 providing chemical / mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. 28 providing and fixing copper tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( for horizontal run ) 29 providing and fixing copper tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( for vertical run ) air condition 30 2 ton inverter cassette ac 5 star inverter ( make: mitsubisi / daikin / toshiba / o general ) noise level indoor ( low / mid2 / mid1 / high ) in db ( a ) not below 45 / 49 / 51.outdoor in not below 54 db ( a ) 31 1.5 ton 5 star inverter split ac ( make: mitsubisi / daikin / toshiba / o general ) noise level indoor ( low / mid2 / mid1 / high ) in db ( a ) not below 45 / 49 / 51.outdoor in not below 54 db ( a ) stablizer ( voltage range: ( 90v to 230 v ) extra copper pipe & electrical wires pvc pipe for drain water fire fighting 32 supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices ( including detectors ) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics / lcd display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory ( eprom ) , power supply unit ( 230± 5% v, 50 hz ) , 48 hrs back up with 24 volt sealed maintenance free batteries with automatic charger. the panel shall have facility to connect printer to printout log and facility to have seamless integration with analog / digital voice evacuation system ( which is part of the schedule of work under sh: pa system ) and shall be complete with all accessories. the panel shall be compatible for ibms system with open protocol bacnet / modbus over ip complete as per specifications. ( edwards est ) 1 loop panel. 1 kva line interactive ups with 30 min battery back up 33 supplying and fixing intelligent addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd. 34 supplying and fixing intelligent addressable type heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd. 35 sypplying and fixing intelligent addressable manual call point having inbuilt short circuit isolator i / c testing and commissiong etc as reqd. 36 addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature 10⁰c to + 55⁰c 37 analogue addressable control module with ip66 casing containing four relay outputs, each containing a potential free dpdt contact with a fail safe and in built short circuit isolator the ambient temperature range shall be 20c to +60c. 37 analogue addressable monitor module with ip66 casing containing four relayinputs, each containing a potential free dpdt contact with a fail safe and in built short circuit isolator the ambient temperature range shall be 20c to +60c. duel led response indicator ( local ) 38 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. ( malhotra / anchor ) 20 mm dia 39 supplying & drawing following sizes of fr pvc insulated copper conductor single core cables in existing surface / recessed pvc conduit etc. as complete as required ( polycab / havels ) 2 x 1.5 sq.mm 40 kanex brand abc type fire extinguisher cap. 6 kg filled with mono ammonium phosphate powder 50% confirms to is 4308, stored pressure type, ugts pressure gauge, gross weight 8.9 kg, empty weight 2.9 kg, can height 530 mm, diameter 150 ± 10mm, discharge time 24 sec, controllable discharge mechanism, jet range 5 meters, average discharge is 90%, applicable on class a, b & c and electrically started fire, fire rating 4a:144b, can construction : deep drawn & co2 mig welded, epdm rubber hose with both end aluminum clamped, internal coating epoxy powder coating, external coating pure polyester powder coating ( uv resistant ) , brass forged valves with safety pin is of ss material, sheet metal thickness : 1.8 mm, isi approved is 15683:2018. 41 kanex brand co2 high pressure portable 4.5 kg fire extinguisher, filled with co2 gas as per is 15222, gross weight 16.4, empty weight 11.9 kg, control discharge mechanism fitted with 1 meter wire braided hose & flat horn with diffuser nozzle for dispersed discharge of co2, discharge time 12 sec, average discharge is 95%, applicable on class b, c and electrically started fire, fire rating 55b, internal coating is not applicable & external coating is of enamel spray painting, powder coated handle, squeeze grip type valve confirm to is 3224 isi marked, co2 cylinder construction: hot spinning by seamless pipes & bearing isi mark, body confirms to is 7285 and peso approved, extinguishers confirmed to is 15683:2018 and isi marked. 42 clean agent 2 kg fire extinguishers filled with hfc based gas electrically nonconductive non corrosive, colorless and non residual gas, applicable classes a, b, c, and electrical fires, ugts pressure gauge, gross weight 3.6 kg, empty weight 1.6 kg, height 380mm, diameter 106 ± 10mm, discharge time 12 sec, controllable discharge mechanism, jet range 3 meters, average discharge is 95%, deep drawn with mig welding technology, epdm rubber hose with special aluminum discharge nozzle, external coating pure polyester powder ( uv resistant ) , internal coating epoxy polyester powder, brass forged valves with safety pin is of ss material, fire rating 1a:21b, confirms to is 15683 & isi marked. 43 supplyy, installation, testing & commissioning of 5 lb capacity novec1230 dlp assembly with automatic valve push in connector for tube 5lb novec 1230 gas mounting bracket end linear adopter and low pressure switch for monitoring system activation. : kanex / fire trace 44 supply, installation, testing and commissioning of linear pneumatic heat detection tube with all necessary fitting and supports. ( rotarex / fire trace ) 45 supply, installation, testing & commissioning of audio visual alarm. : kanex / fire trace 46 automatic type 5 kg fire extinguishers hfc 236fa, applicable fire classes a, b & c, ugts pressure gauge, empty weight 2.64 kg, full weight 7.64 kg, can height 375mm, diameter 230 ± 10mm, sheet metal thickness : 2 mm, body construction deep drawn with mig welding technology, brass forged sprinkler valves with nozzle is specially designed to give more than 99% discharge. together with orifice characteristic to cover adequately fire risks with scattering cone of 40 to 45° angle. external pure polyester ( uv resistant ) and internal epoxy polyester powder coated, heat sensitive glass bulb of 68 °c. area covered will be 2 2.5 m2 and volume of coverage is 7 m3. brand : kanex cctv 47 network switch: 24 x 10 / 100 / 1000base t, poe, fixed, 2 x sfp 100 / 1000 mbps, 52 gbps sitching performance capacity, 39 mbps forwarding performance rate. 525 k byte packet buffer, 8k mac address table. 9k bytejumbo frame, 170 watt poe power. 48 bullet camera : 1 / 3 3 megapixel progressive scan cmos, pixels 2304 ( h ) x 1296 ( v ) , electronic shutter speed automanual, 1 / 3 ( 4 ) 1 / 100000s, min illumination 0.1 lux, f1.4 ( color ) ; 0 lux ( ir leds on ) , ir distance upto 100 ft ( 30 m ) , depending upon scene reflectance.day / night auto ( icr ) / color / bw, backlight compensation blc / hlc / dwdr , white balance auto / manual, gain control auto / manual, noise reduction3d, privacy masking upto 4 areas, lens focal length 2.7 12mm, max, aperture f1.4, focus control auto , horizontal angle of view 86 28 degree, lens type motorized focus / zoom, video compression h 264 ( main / high / baseline profile ) / mjpeg, resolution 3 mp ( 2304 x 1296 ) , 1080p ( 1920x1080 ) , 720p ( 1280x720 ) , d1 ( 704x576 / 704x480 ) , cif ( 352x288 / 352x240 ) , frame rate main stream 3 mp ( 1 20 fps ) , 1080p ( 1 25 / 30 fps ) , frame rate 49 dome camera: image sensor 1 / 3 3 magapixel progressive scan cmos, effective pixels 2304 ( h ) x 1296 ( v ) , electronic shutter speed min. illumination 0.045 lux, f2.1 ( color ) , 0 lux ( ir leds on ) , ir distance upto 100 ft ( 30 m ) , depending on scene reflectance, day / night auto ( icr ) / color / bw, backlight compensation blc / hlc / dwdr, white balance, auto / manual, gain control auto / manual, noise reduction 3d, privacy masking upto 4 areas, focal length 2.8mm, max. aperture f2.1, horizontal angle of view 92degree, lens type fixed, video compression h264 ( main / high / baseline profile ) / mjpeg, resolution 3mp ( 2304x1296 ) , 1080p ( 1920x1080 ) , 720p ( 1280x720 ) , d1 ( 704x576 / 704x480 ) 50 video recorder: simultaneous multi channel live view, real time recording, playback, network operation, remote access, usb backup, user interface support 16 bit true color graphical menu interface and mouse operation.preview screen 1 / 4 / 8 / 16 / 24 windows, ip video input 24 channels, video standard pal ( 625 line, 50t / s ) , ntsc ( 525 line, 60t / s ) , video compression h264 high profile, display moitor d1;vga & hdmi, hd ( support 1920x1080, 1280x720, 1440x900, 1260x1024, 1024x768, 800x600 ) 51 display: screen size 42 inch or above ( lg / sony / samsung / philips ) , panel technology ips, aspect ratio 16:9, native resolution 1920x1080 ( fhd ) , brightness 350nit or higher, contrast ratio 1100:1 or higher, dynamic cr 500, 000:1 or higher, viewing angle ( hxv ) 178x178, orientation portrait & landscape, operation temperature 0 degree c to 40 degree c, safety ul, eul, emc fcc class a, ip video unit 16 channel, 1 ch, rca ( 2.0 vp p, 1kohm ) two way audio input, 100 mbps incoming bandwidth, 80 mbps bandwidth, 128 remote connection, hdmi / vga output : 1 ch, resolution hard disk 4 tb camera installation and connectivity telephone 52 epabx with 50 line extension up to 80 line with 2 slt / 2 console the equipment shall be electronic type. it shall have microprocessor / micro controller based.it shall employ pcm / tdm / ip, 100% non blocking, ip digital switching technology.it shall have distributed processing architecture, slic and smt design.system power supply should be in built and smps type which input which input ranges from 90 – 265 vac, 48 60 hz & it has to be battery charger circuit inbuilt, so that, in case of power failure the psu can automatically switch to battery and vice versa. it should be suitable for dtmf as well as fsk type of telephone instruments.its capacity shall be suitable for maximum 96 numbers of c.o. lines, 120 analog extension lines and 500 ip extensions. 53 supply, installation, testing & commissioning of termination box for 50 pair epabx system complete as required 54 base phone cli ( panasonic / beetal ) landline phone with caller id facility corded phone numerical keypad 35 call logs3 display lines disclaimer, tone / pulse switchable ring led indication flash pause dynamic change over from pulse tone, 1 year manufacturer warranty 55 digital console phone 56 network switch : 24 x 10 / 100 / 1000base t, poe, fixed, 2 x sfp 100 / 1000 mbps, 52 gbps sitching performance capacity, 39 mbps forwarding performance rate, 525 k byte packet buffer, 8k mac address table, 9k byte jumbo frame, 170 watt poe power. 57 smart ups on line, 5.4 kw / 6 kva with 1 hour backup12 v 65 ah smf battery ups toplogy double conversion on line, power rating ( va / watts ) 5400watts / 6000va, form factor rack / tower convertible; output power capacity 5400 watts / 6000 va, max configurable power 5400watts / 6000va, nominal output voltage 230v, output voltage note configurable for 220 : 230 or 240 nominal output voltage, efficiency at full load 94.00%, output voltage distortion less than 3%, output frequency ( sync to mains ) 50 / 60 hz + / 3 hz, crest factor 03:01, waveform type sine wave, output connections ( 1 ) *hard wire 3 wire ( 8 ) * ( h n + g ) iec 320 c13 ( 8 ) , bypass built in bypass, output short circuit protection yes, parallel redundancy ( option ) 1 + 1, nominal input voltage 230v, input power factor>0.98, input frequency 40 70hz, input connections terminal block, protection thermal circuit breaker ( 250vac / 20a ) , input voltage range for main operations full load 160 285v, input voltage range for mains operation half load 160 285v, high voltage withstand capability 420 vac, green mode range 210 250 vac ( 230 v ) , battery type mintenance free sealed lead acid battery with suspended, electrolyte. 12v 65 ah smf battery for 60 min battery back up. 58 supplying and drawing following pair 0.5 sq. mm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed pvc conduit as required. 2 pair networking 59 supplying & fixing rj 45 type computer socket suitable for cat 6 on modue gi box along with base and cover plate in surface or in recess including making connection , soldering etc as required. supplying and drawing utp 4 pair cat 6 lan cable patch cord 1 meter patch cord 2 meter 60 24 port gbe smart managed switch with gbe uplink interfaces 24 ports 10 / 100 / 1000mbps+4 sfp;port standards & functions ieee 802.3 10base t ethernet ( twisted pair copper ) , ieee 802.3u 100basetx fast ethernet ( twisted pair copper ) , ieee 802.3ab 1000base t gigabit ethernet ( twisted pair copper ) , ieee 802.3az compliance autonegotiation, ieee 802.3x flow control; full / half duplex full / half duplex for 10 / 100 mbps speeds, full duplex for gigabit speed;media interface exchange auto mdi / mdix adjustment for all twisted pair ports;switching capacity 56 gbps; transmission method store and forward; mac address table 16, 000 entries per device, maximum 64 bytes packet forwarding rate 41.7 mpps, packet buffer memory 1.5 mb, maximum power consumption 22.45 watts, standby power consumption 17.84 w / 240 v, acoustics 0 dba heat dissipation 76.55 btu / hr certifications ce ( lvd ) 61 category 6, utp 24 port patch panel size 482.6mm x 44.2 ( 19’’ x 1u ) , panel material steel fully powder coated, unshielded rj 45, plug insertion cycle 750 times dc resistance 72ω max, voltage rating 72 vdc max, current rating 1.5a max 62 supply fitting fixing rack 19 12u fully powder coated complete etc as required with complete accessories ( 5 amp x 6 socket, wire manager, rack fan ) valrack / netrack make. 63 wireless n access point interface one 10 / 100mbps rj45 port ( auto mdi / mdix ) , button wps button, reset button, external power supply 9vdc / 0.6a, antenna type 5dbi detachable omni directional antenna, frequency 2.4 2.4835ghz, wireless standards ieee 802.11n, ieee 802.11g, ieee 802.11b, wireless security ssid enable / disable mac address filter 64 / 128 / 152 bit wep encryption wpa / wpa2 / wpa psk / wpa2 psk ( aes / tkip ) encryption wireless modes ap mode, multi ssid mode, client mode, repeater mode ( wds / universal ) , bridge mode, tplink / cisco / netgear panel meter board mb 1 incomer 125a, 415v, ics=icu=25ka rupturing capacity, fp, mccb with extended rotary handle 1 no. 1 no. type 1+2 class i+ii lightning surge arrester 3 pole plus neautral. obo make type no. v25 b+c 3npe385 as per item no. 5094478 with mpcb busbar heat shrinked colour coded aluminium bus bars with smc / dmc busbar supports, nuts & bolts with spring washers. a set of tpn 200a al bus bars. current density shall be 1a / sq.mm instrumentation for incoming 1 no. three phase 0 500v digital voltmeter with selector switch 1 no. 0 125a digital ammeter with cts 125 / 5a and selecter witch 1 set of led type phase indicating lamps with hrc fuses meter compartments meter compartments with electonic meters three phase direct type 10 nos. the vendor shall submit details before fabrication outgoings 25 32a fp mcb 12 nos. supply of main l.t. panel fabricated out of 16swg m.s. iron sheets, compartmentalized type, with epoxy powder protective paint having sufficient housing compartpents for mounting of switchgears as per below mentioned specifications, make: kde / scpl / equivalent design, fabrication and supply of suitable electrical grade enclosure, compartmentalized type with epoxy powder protective paint and panel is to be fabricated out of 16swg make: kde / scpl / equivalent supply and installation of 1000 amp of electrolytic aluminium busbar for power load section. supply and installation of proper dmc busbar supporting system suitable for 1000 amp ratings. 250 amp, 35 ka, tpmccb supply of 160amp, 4pole mccb extended rotary handle make: abb / ge / siemens. 25 / 100 amps. 4 pole mccb, 16 ka cable 3.5 core, 300 sq. mm xlpe / pvc insulated sheathed ( heavy duty ) armoured electric cable with aluminium conductor. 3.5 core, 95 sq. mm xlpe / pvc 3.5 core, 150 sq. mm xlpe / pvc 3.5 core, 185 sq. mm xlpe / pvc detailed estimate for the proposed renovation and upgradation work for food test lab at first & 2nd floor, patliputra industrial area, patna. n.s. 1 parking deck flooring with high build, solvent free textured finish epoxy coating with roller applied 5 mm thick epoxy resin based floor coating nitoflor fc150 over epoxy resin screed nitoflor tf 5000 the intended surface shall be prepared by mile scarification to get mechanical key effect to the primer and the concrete surface for ensuring maximum bonding. strong degrease shall be used to remove the oil deposit on the concrete if any. dust and loose particles shall be cleaned using vacuum cleaners . after which nitoprime 25 shall be applied after mixing the base and hardener mechanically using a slow speed heavy duty drilling machine ( 400 to 500 rpm ) fitted with a suitable paddle to achieve homogeneous mix and applied on the prepared surface. after primer nitoflor tf 5000 shall be applied as a base layer after mixing the base hardener and aggregates throughly and poured on the primed surface and spread evenly to maintain the required thickness of 3 mm. the material should be tampered with a wooden float to ensure complete compaction and finally finished to closed even texture using a steel trowel and cured for seven days. as a finishing coat nitoflor fc 150 shall be applied over the screed surface after mixing mechanically the three components using heavy duty slow speed paddle mixer until achieving a homogeneous mix and spread on the prepared area using medium haired rol;ler for a thickness of 400 microns in two coat. 8.2 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement: 4 coarse sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels. 8.2.2 granite of any colour and shade 8.2.2.2 area of slab over 0.50 sqm 8.3 extra for providing edge moulding to 19 mm thick marble stone counters, vanities etc. over item no. 8.2 mm thick marble stone counters, vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. granite work 8.3.2 granite work 26.27 providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ≥85%, thermal conductivity k=0.057 w / m k, fire performance as per ( bs 476 pt 6 & 7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanised iron section of 0.33mm thick ( galvanized @120gsm ) comprising of main t runners of 15x32mm of length 3000mm, cross t of size15x32mm of length 1200mm and secondary intermediate cross t of size 15x32mm of length600mm to form grid module of size 600x600mm suspended from ceiling using galvanized mild steel item ( galvanised @80gsm ) 50mm long 8mm outer diameter m 6 dash fasteners, 6mm diameter fully threaded hanger rod upto 1000mm length and l shape level adjuster of size 85x25x2mm, spaced at 1200mm centre to centre along main t. the system should rest on periphery walls / partitions with the help of gi perimeter wall angle of size 24x24x3000mm made of 0.40 mm thick sheet, to be fixed to the wall with the help of plastic rawl plug at 450mm centre to centre & 40mm long dry wall s.s. screws. the exposed bottom portion of all t sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. the work shall be carried out as per specifications, drawings and as per directions of the engineer in charge. 26.27.2 with 20mm thick beveled tegular mineral fibre false ceiling tile ( nrc0.7 ) . 12.45.3 providing and fixing false ceiling at all height including providing and fixing of frame work made up of special sections power pressed from m.s. sheet and galvanized in accordance with zinc coating of 120 gms / sqm as per is:277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts to the angle hanger of 25x25x5 mm of required length, and other end of angle hanger being fixed with nut and bolts to g.i. channels 45x15x0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm centre to centre shall be fixed in a direction perpendicular to g.i. channel with connection clips made out of 2.64 mm dia x 230 mm long g.i. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450 mm centre to centre with 25 mm long drive all screws @230 mm interval including jointing and fixing to a flush finish of tapered and square edges of the gypsum board with recommended filler, paper tapes, finishers and two coats of primer suitable for gypsum board as per manufacturers specification and also including the coat of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per the drawing and specification and direction of the the engineer in charge but excluding the cost of painting. 12.5 mm thick tapered edge gypsum moisture resistant board 12.62 extra for any sunk or raised moulding in the plaster of paris ( gypsum anhydrous ) ceilng .all complete as per specification and direction of e / i. ns 2 supplying fitting and fixing roman blinds in jacard cloth finish as per company specification and as per approved colour and sample inclusive of all taxes and royalty all complete as per specifications / approval and direction of engineer in charge. n.s. 3 providing & fixing double skin laminated both side wpc partition upto specified height with 1.0 mm lamination of greenply / marino / century mica over 12 mm thick wpc of alstone / greenply / century ( min wt. 550kg / cum ) make fitted and fixed both sides over aluminium frame of 50 x 50mm posts at 60 cm centres and 50x50mm horizontal members at approx 60 cm centers including cost of anchoring the partition to floors, walls and ceiling properly as per drawing including making hidden doors as per drawing all complete as per drawing, specifications and direction of e / i. providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of engineer in charge ( door handle , lock, and stopper etc . n.s 4 supplying fitting and fixing glass door handles, h type ( qbghl 5 ) made up of stainless steel brushed steel finish 300 mm heigh / equivalent make all complete including taxes and royalty as per approval and direction of e / i. n.s 5 supplying fixing and fitting high security corner lock for patch fitting ( qbpl 1 make ) brushed steel finish made of graded aluminium alloy cast housing slim and compact size light in weight all complete as per specification and direction of e / i ns 6 providing and fixing of 1.0mm laminated ( greenlam / century / merino ) panelling upto specified height over 12 mm thick wpc board of alstone / greenply / century make fitted and fixed over aluminium frame of 25 x 25mm posts at 30 cm centres and 25 x 25mm horizontal members at approx 30 cm centers including cost of anchoring the panelling to walls properly including termite treatment as per drawing specification and direction of e / i. 14.1.1 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground, all complete as per direction of e / i. cement mortar 1:4. 13.74 removing white or colour wash by scraping and sand papering and preparing the surface smooth including necessary repair scratches etc. complete 13.80 a.2 providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 13.92 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. 13.92.1 two or more coat on new surface. 9.48 providing and fixing m.s grills of required pattern in frames of windows etc. with m.s flats, square or round bars etc. all comlete. 9.48.1 fixed to steel windows by welding. 13.94 painting with sythetic enamel paint of approved brand and manufacture to give an even shade. 13.94.1 two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 15.23 dismantling tile works in floor and roofs laid in cement mortar including stacking material within 50 metres lead. 15.23.2 for thickness of tiles above 25 mm and upto 40 mm 15.7 demolishing brick work including stacking of serviceable material and disposal of unserviceable materials within 50 metres lead : 15.7.4 in cement mortar disposal of building rubbish / malba / similar unserviceable, dismantled or waste waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer in charge, beyond 50 m initial section 3: electrical work s.h. i : wiring 1.3.3 point wiring in pvc conduit, with modular type switch: wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit, with modular switch, modular plate, suitable g.i. box etc. as required. group c 1.4 twin control point wiring in pvc conduit with modular type switch: wiring for twin control light point with 1.5 sq mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit, 2 way modular switch, modular plate, suitable g.i. box etc. as required. 1.5 power plug wiring in pvc conduit ( 2x4 sq. mm ) : wiring for light / power plug with 2 x 4 sq. mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit alongwith 1 no. 4 sq. mm fr pvc insulated copper conductor singlre core cable for loop earthing as required. ( for 15 amp socket ) 1.7 circuit / sub main wiring in pvc conduit : wiring for circuit / submain wiring alongwith earthwire with the following sizes of pvc insulated copper conductor, singlre core cable in surface / recessed pvc conduit as required. 1.7.1 2 x 1.5 sq.mm. + 1 x 1.5 sq. mm earth wire 1.7.2 2 x 2.5 sq.mm. + 1 x 2.5 sq. mm earth wire 40185 4 x 4 sq.mm. + 1 x 4 sq. mm earth wire 40550 4x 6 sq.mm. + 1 x 6 sq. mm earth wire 1.16 telephone wiring in existing conduit: supplying and drawing following pair, 0.5 sq. mm fr pvc insulated copper conductor, unarmoured telephone cables in existing surface / recessed pvc conduit as required 1.16.2 2 pair 1.21 s / f pvc conduit: supplying and fixing of following sizes of pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recess conduit as required. 1.21.1 20 mm 1.24 s / f modular type switch / socket : supplying and fixing following modular type switch / socket on the existing modular switch / socketon the existing modular plate& switch box including connections but excluding modular plate etc. as required. 1.24.4 3 pin, 5 / 6 amps socket outlet 1.24.5 6 pin, 15 / 16 amps socket outlet 1.24.6 telephone socket outlet 1.24.8 bell push 1.27.1 s / f modular boxes, base & cover plate: supplying and fixing following size / modules, gi box along with modular base & cover plate for modular switches in recess as required. 1 or 2 module ( 75 mm x 75 mm ) 1.31 s / f light plug point modular type accessories: supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch, connection, painting etc. as required. ( for light plugs to be used in non residential buildings. ) 1.32 s / f power plug point modular type accessories: supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5 / 6 & 15 / 16 amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc. as required. 5.4 supplying and fixing replaceable compact commercial batten suitable for single tb led tube complete with 20 watt led polycarbonate tb tube with built in driver etc. directly on wall / ceiling including connections with 1.5 sq. mm fr pvc insulated copper conductor etc. as required. 1.37 providing and fixing ding dong call bell suitable for single phase, 230 volts complete as required. 8.15 supply and installation of regular / standard model a.c. ceiling fan of 1200 mm sweep with service value ( cm / mm ) minimum 4.00, air delivery minimum 270 cum / min including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq mm fr pvc insulated copper conductor etc as required. 5.7 supplying and fixing recess mounted following types led downlighter with minimum efficacy 100 lm / w in pressure die cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm frls pvc insulated copper conductor cable etc as required. 5.7.1 5 / 7 watt 5.7.5 18 watt 5.9 supplying and fixing recess mounted 36 watt led flat panel ( 2 x 2 ) with minimum efficacy 100 lm / w which provides soft light and glare free symmetrical illumination suitable for armstrong / grid ceiling and integrated electronic driver etcdirectly on false ceiling including connections with 1.5 sq.mm frls pvc insulated copper conductor cable etc as required. 5.11 supplying and fixing wall mounted light bracket / fixture made with polycarbonate suitable for single 9 / 10 watt led lamp directly on wall including connections etc as required. ( but without lamp ) 6.1.6 supplying and fixing of following types lamp in the existing electrical fitting / fixtures etc. as required. 14 / 15 watt cfl lamp. 2.12 s / f c series, sp mcb: supplying and fixing following rating, 240 / 415 volts, c curve, miniature circuit breaker, suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 2.12.1 6 / 32 amps, single pole 2.12.2 6 / 32 amps, spn 2.12.4 6 / 32 amps, triple pole and neutral 2.12.8 40 amps, triple pole and neutral 2.19 supplying and fixing 20amp 240 volts spn mcb industrial type, power socket with 25amp spn mcb and 25 amps top in proper size steel box and plate as required. all complete as per instructions of elec.er. / architect. 8.11 supply and fixing of fabricated electrical control panel of cubical construction, floor / wall mounted type, fabricated out of 16 swg crca sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, bus bar chamber, insulator and complete in all respect etc and panel manufactures must be approved by cpri. ( but without ryb inicator, ammeter, voltmeter, inter connection copper conductor cable / solid copper strip, switchgears etc. ) ...

Bihar Industrial Area Development Authority - Bihar

42981157 request for proposal ( rfp ) for selection of firm / agency / supplier for supply, installation, testing and commissioning of different machines including civil, electrical and other fixtures for setting up food testing lab in upendra maharathi shilp anusandhan sansthan, patna, bihar. 1 highly sensitive triple quadrupole lcms / ms system 2 gas chromatographs with ecd, fid, fpd detector, with headspace and auto sampler ( auto sampler to be provided ) with 5 years consumable and warranty extended upto 5 years 3 gc ms ms with ecd, fid, fpd detector, with headspace and auto sampler ( auto sampler to be provided ) with 5 years consumable and warranty extended upto 5 years 4 icpms accessories and microwave digestion system 5 double beam atomic absorption spectrophotometer 6 high performance liquid chromatography ( gradient ) with uv and fld detector, auto sampler & essential columns with accessories with 5 years consumable and warranty extended upto 5 years 7 uv vis spectrophotometer 8 centrifuge with 5 years consumable and warranty extended upto 5 years 9 ultra low temperature 80 ult freezer 10 ph meter with 5 years consumable and warranty extended upto 5 years 11 elisa reader, filter based plate reader with 5 years consumable and warranty extended upto 5 years 12 heating mantles with 5 years consumable and warranty extended upto 5 years 13 laboratory precision oven uniform temperature 300 o c with 5 years consumable and warranty extended upto 5 years 14 cyclotec lab grinding millwith 5 years consumable and warranty extended upto 5 years 15 magnetic stirrer with 5 years consumable and warranty extended upto 5 years 16 magnetic stirrer with hotplate with 5 years consumable and warranty extended upto 5 years 17 block digestor for eight samples with 5 years consumable and warranty extended upto 5 years 18 moisture analyzer with 5 years consumable and warranty extended upto 5 years 19 muffle furnace 930 degree c with 5 years consumable and warranty extended upto 5 years 20 rectangular hot plate with 5 years consumable and warranty extended upto 5 years 21 refrigerated microcentrifuge with 5 years consumable and warranty extended upto 5 years 22 refrigerators, 2 to 8degreec, capacity 1000l with smart view with 5 years consumable and warranty extended upto 5 years 23 refrigerated incubator orbital shaker ( stackable ) with 5 years consumable and warranty extended upto 5 years 24 soxhlet extraction unit with 5 years consumable and warranty extended upto 5 years 25 nitrogen concentrator ( turbo vap. concentrator ) with 5 years consumable and warranty extended upto 5 years 26 solid phase extraction manifold with 5 years consumable and warranty extended upto 5 years 27 vaccum fitration apparatus along with vaccum pump with 5 years consumable and warranty extended upto 5 years 28 multi tube vortex with mixing, heating, and cooling functions with 5 years consumable and warranty extended upto 5 years 29 analytical weight box, e2 with 5 years consumable and warranty extended upto 5 years 30 analytical weight box, e2, with 5 years consumable and warranty extended upto 5 years 31 analytical balance, 220g x 0.1mg with internal calibration with 5 years consumable and warranty extended upto 5 years 32 microbalance, 5.2g x 0.001mg with internal calibration and static eliminator with 5 years consumable and warranty extended upto 5 years 33 precision balance, 6200g x 0.1 with external calibration with 5 years consumable and warranty extended upto 5 years 34 micro pipette, 30 300 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 35 micropipette, 1 to 10 ml, eppendorf with 5 years consumable and warranty extended upto 5 years 36 micro pipette, 2 to 20 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 37 micro pipette, 10 to 100 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 38 micro pipette, 20 to 200 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 39 micro pipette, 100 to 1000 μl, eppendorf with 5 years consumable and warranty extended upto 5 years 40 rotary vacuum evaporator along with heating bath, diaphragm pump, interface and recirculating chiller rotary evaporator and heating bath with 5 years consumable and warranty extended upto 5 years 41 digital stop watch , 1 real time pcr system with 5 years consumable and warranty extended upto 5 years 2 b.o.d cooling incubators with 5 years consumable and warranty extended upto 5 years 3 vertical laboratory autoclave ( radial locking ) with 5 years consumable and warranty extended upto 5 years 4 laboratory precision oven uniform temperature 300 o c with 5 years consumable and warranty extended upto 5 years 5 horizontal laminar air flow with 5 years consumable and warranty extended upto 5 years 6 digital top pan balance ( 20 gm 800 gm ) , with 5 years consumable and warranty extended up to 5 years 7 analytical balance ( 0.01mg 20 gm ) , with 5 years consumable and warranty extended upto 5 years 8 stability chamber with 5 years consumable and warranty extended upto 5 years 9 biosafety cabinet type ii b, with 5 years consumable and warranty extended upto 5 years 10 deep freezer 20°c, with 5 years consumable and warranty extended upto 5 years olsc 119 12 11 stomacher, with 5 years consumable and warranty extended upto 5 years 12 homogenizer / lab stirrer, with 5 years consumable and warranty extended upto 5 years outer & inner ss 13 ph meter, with 5 years consumable and warranty extended upto 5 years 14 lab grinding mill ( homogenizer ) with 5 years consumable and warranty extended upto 5 years olsc ls 01 15 vortex mixer, with 5 years consumable and warranty extended upto 5 years 16 refrigerated microcentrifuge with 5 years consumable and warranty extended upto 5 years 17 non refrigerated microcentrifuge with 5 years consumable and warranty extended upto 5 years 18 gel documentation system with printer, with 5 years consumable and warranty extended upto 5 years 19 biosafety cabinet type ii b, with 5 years consumable and warranty extended upto 5 years 20 sonicator, with 5 years consumable and warranty extended upto 5 years 21 binocular microscope / 3d microscope, with 5 years consumable and warranty extended upto 5 years 22 uv cabinet, with 5 years consumable and warranty extended upto 5 years 23 serological water bath, with 5 years consumable and warranty extended upto 5 years 24 electronic colony counter with 5 years consumable and warranty extended upto 5 years 1 wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit, with modular type switch, modular plate, suitable size g.i. box and earthing the point with 1.5 sq.mm. fr pvc insulated copper conductor single core cable etc.as required group c 2 wiring for light / power plug with 2x4 sq.mm fr pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit along with 1 no 4 sq.mm. fr pvc insulated copper conductor single core cable for loop earthing as required. 3 wiring for circuit / submain wiring along with earth wire with the following sizes of fr pvc insulated copper conductor, single core cable in surface / recessed pvc conduit as required. 2x2.5 sq.mm +1x2.5 sq.mm 2 x 6 sq.mm + 1 x 6 sq.mm. earth wire 2 x 10 sq.mm. + 1 x 10 sq.mm. earth wire 4 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 4 x 6 sq. mm + 1 x 6 sq. mm earth wire 4 x 10 sq. mm + 1 x 10 sq. mm earth wire 4 x 16 sq. mm + 1 x 16 sq. mm earth wire 4 supplying and fixing pvc / g.i box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required ( adopter box above each d.b ) . 5 supplying and fixing suitable gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pinm 5 / 6 and 15 / 16 amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc. as required. ( for power plug ) 6 supplying and fixing suitable size g.i box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5 / 6 amps modular socket outlet and 5 / 6 amps modular type switch, connection, painting etc., as required. ( for light plugs to be used in non residential buildings ) 7 supply & fixing 8 way double door sp & n, sheet steel, mcb distribution board, 240 volts, on surface / in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required ( but without mcb / rccb / isolator ) lighting db ( a ) 40 amps double pole mcb isolator : 1 no. ( b ) outgoing 6 / 32 amps sp mcb ( b series ) :6 nos. 8 supply & fixing 4 way ( 4+12 ) double door tp & n, sheet steel, mcb distribution board, 415 volts, on surface / in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required ( but without mcb / rccb / isolator ) power db ( a ) 63 amps double pole mcb isolator : 1 no. 9 ( b ) outgoing 16 / 32 amps sp mcb ( c series ) : 12 nos. s / f following modular type switch / socket on the existing modular plate and switch box including connection but excluding modular plate etc as required. 10 tv antenna socket outlet 11 s / f electronics musical call bell suitable for d.c / a.c. single phase 230 copmplete as required. 12 supplying and fixing batten / angle holder incluiding connection etc as required. 13 supplying and fixing 2 pin, 5 amp, celling rose on the existing junction box / pvc box incluiding connection etc as required. 14 s / f modular blanking plate on the existing modular plate and switch box excluding modular plate as required. 15 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required. electrical fixture fitting 16 supply and installation of 300 mm 230volt ac exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required. 17 supply & installation 400 mm dia 230 volt ac wall / cabin fan including fixing the bracket making connection testing commissioning etc as required. 18 supply and fixing recess mounted 18 watt led vertical downlighter complete with all accessories and replaceable electronic driver directly on false ceiling including connection with 1.5 sq mm fr insulated copper conductor cable and earthing the body etc as required 19 supplying and fixing indoor recess mounting 36 watt led flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. directly on false ceiling including connection with 1.5 sqmm fr pvc insulated copper conductor cable and earthing the body etc as required. 20 supplying and fixing of following types lamp in the existing electrical fitting / fixtures etc. as required. 10 / 12 watt led lamp 21 supplying and fixing 90 watt led type street light with die cast aluminium housing for ingress protection of ip65 and complete with all accessories etc, on pole / building including connection with fr pvc insulated copper conductor cable and earthing the body etc. as required. 22 supplying and fixing following sizes of pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. section 4: fire extinguishers p / f with brackets wall mounted fire extinguishers as per details below: 23 abc power type ( stored pressure ) fire extinuisher 4 kg .capacity , isimark ( is: 15683 ) squeeze gripe valve, operating temperature ( +5 deg. to ( +55 ) deg.for class 3a type of fire with abc powder , complete in all respect. 24 co2 type fire extinguisher 4.5kg capacity isi mark ( is : 15683 ) squeeze grip value , operating temperature ( 30deg. to 55deg.foe class 13b type of fire fitted with 1mt.hose & pvc hoen, complete in all respect. earthing 25 providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required. 26 providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface / recessed conduit / submain wiring / cable as required. 27 providing chemical / mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. 28 providing and fixing copper tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( for horizontal run ) 29 providing and fixing copper tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( for vertical run ) air condition 30 2 ton inverter cassette ac 5 star inverter ( make: mitsubisi / daikin / toshiba / o general ) noise level indoor ( low / mid2 / mid1 / high ) in db ( a ) not below 45 / 49 / 51.outdoor in not below 54 db ( a ) 31 1.5 ton 5 star inverter split ac ( make: mitsubisi / daikin / toshiba / o general ) noise level indoor ( low / mid2 / mid1 / high ) in db ( a ) not below 45 / 49 / 51.outdoor in not below 54 db ( a ) stablizer ( voltage range: ( 90v to 230 v ) extra copper pipe & electrical wires pvc pipe for drain water fire fighting 32 supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices ( including detectors ) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics / lcd display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory ( eprom ) , power supply unit ( 230± 5% v, 50 hz ) , 48 hrs back up with 24 volt sealed maintenance free batteries with automatic charger. the panel shall have facility to connect printer to printout log and facility to have seamless integration with analog / digital voice evacuation system ( which is part of the schedule of work under sh: pa system ) and shall be complete with all accessories. the panel shall be compatible for ibms system with open protocol bacnet / modbus over ip complete as per specifications. ( edwards est ) 1 loop panel. 1 kva line interactive ups with 30 min battery back up 33 supplying and fixing intelligent addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd. 34 supplying and fixing intelligent addressable type heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd. 35 sypplying and fixing intelligent addressable manual call point having inbuilt short circuit isolator i / c testing and commissiong etc as reqd. 36 addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature 10⁰c to + 55⁰c 37 analogue addressable control module with ip66 casing containing four relay outputs, each containing a potential free dpdt contact with a fail safe and in built short circuit isolator the ambient temperature range shall be 20c to +60c. 37 analogue addressable monitor module with ip66 casing containing four relayinputs, each containing a potential free dpdt contact with a fail safe and in built short circuit isolator the ambient temperature range shall be 20c to +60c. duel led response indicator ( local ) 38 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. ( malhotra / anchor ) 20 mm dia 39 supplying & drawing following sizes of fr pvc insulated copper conductor single core cables in existing surface / recessed pvc conduit etc. as complete as required ( polycab / havels ) 2 x 1.5 sq.mm 40 kanex brand abc type fire extinguisher cap. 6 kg filled with mono ammonium phosphate powder 50% confirms to is 4308, stored pressure type, ugts pressure gauge, gross weight 8.9 kg, empty weight 2.9 kg, can height 530 mm, diameter 150 ± 10mm, discharge time 24 sec, controllable discharge mechanism, jet range 5 meters, average discharge is 90%, applicable on class a, b & c and electrically started fire, fire rating 4a:144b, can construction : deep drawn & co2 mig welded, epdm rubber hose with both end aluminum clamped, internal coating epoxy powder coating, external coating pure polyester powder coating ( uv resistant ) , brass forged valves with safety pin is of ss material, sheet metal thickness : 1.8 mm, isi approved is 15683:2018. 41 kanex brand co2 high pressure portable 4.5 kg fire extinguisher, filled with co2 gas as per is 15222, gross weight 16.4, empty weight 11.9 kg, control discharge mechanism fitted with 1 meter wire braided hose & flat horn with diffuser nozzle for dispersed discharge of co2, discharge time 12 sec, average discharge is 95%, applicable on class b, c and electrically started fire, fire rating 55b, internal coating is not applicable & external coating is of enamel spray painting, powder coated handle, squeeze grip type valve confirm to is 3224 isi marked, co2 cylinder construction: hot spinning by seamless pipes & bearing isi mark, body confirms to is 7285 and peso approved, extinguishers confirmed to is 15683:2018 and isi marked. 42 clean agent 2 kg fire extinguishers filled with hfc based gas electrically nonconductive non corrosive, colorless and non residual gas, applicable classes a, b, c, and electrical fires, ugts pressure gauge, gross weight 3.6 kg, empty weight 1.6 kg, height 380mm, diameter 106 ± 10mm, discharge time 12 sec, controllable discharge mechanism, jet range 3 meters, average discharge is 95%, deep drawn with mig welding technology, epdm rubber hose with special aluminum discharge nozzle, external coating pure polyester powder ( uv resistant ) , internal coating epoxy polyester powder, brass forged valves with safety pin is of ss material, fire rating 1a:21b, confirms to is 15683 & isi marked. 43 supplyy, installation, testing & commissioning of 5 lb capacity novec1230 dlp assembly with automatic valve push in connector for tube 5lb novec 1230 gas mounting bracket end linear adopter and low pressure switch for monitoring system activation. : kanex / fire trace 44 supply, installation, testing and commissioning of linear pneumatic heat detection tube with all necessary fitting and supports. ( rotarex / fire trace ) 45 supply, installation, testing & commissioning of audio visual alarm. : kanex / fire trace 46 automatic type 5 kg fire extinguishers hfc 236fa, applicable fire classes a, b & c, ugts pressure gauge, empty weight 2.64 kg, full weight 7.64 kg, can height 375mm, diameter 230 ± 10mm, sheet metal thickness : 2 mm, body construction deep drawn with mig welding technology, brass forged sprinkler valves with nozzle is specially designed to give more than 99% discharge. together with orifice characteristic to cover adequately fire risks with scattering cone of 40 to 45° angle. external pure polyester ( uv resistant ) and internal epoxy polyester powder coated, heat sensitive glass bulb of 68 °c. area covered will be 2 2.5 m2 and volume of coverage is 7 m3. brand : kanex cctv 47 network switch: 24 x 10 / 100 / 1000base t, poe, fixed, 2 x sfp 100 / 1000 mbps, 52 gbps sitching performance capacity, 39 mbps forwarding performance rate. 525 k byte packet buffer, 8k mac address table. 9k bytejumbo frame, 170 watt poe power. 48 bullet camera : 1 / 3 3 megapixel progressive scan cmos, pixels 2304 ( h ) x 1296 ( v ) , electronic shutter speed automanual, 1 / 3 ( 4 ) 1 / 100000s, min illumination 0.1 lux, f1.4 ( color ) ; 0 lux ( ir leds on ) , ir distance upto 100 ft ( 30 m ) , depending upon scene reflectance.day / night auto ( icr ) / color / bw, backlight compensation blc / hlc / dwdr , white balance auto / manual, gain control auto / manual, noise reduction3d, privacy masking upto 4 areas, lens focal length 2.7 12mm, max, aperture f1.4, focus control auto , horizontal angle of view 86 28 degree, lens type motorized focus / zoom, video compression h 264 ( main / high / baseline profile ) / mjpeg, resolution 3 mp ( 2304 x 1296 ) , 1080p ( 1920x1080 ) , 720p ( 1280x720 ) , d1 ( 704x576 / 704x480 ) , cif ( 352x288 / 352x240 ) , frame rate main stream 3 mp ( 1 20 fps ) , 1080p ( 1 25 / 30 fps ) , frame rate 49 dome camera: image sensor 1 / 3 3 magapixel progressive scan cmos, effective pixels 2304 ( h ) x 1296 ( v ) , electronic shutter speed min. illumination 0.045 lux, f2.1 ( color ) , 0 lux ( ir leds on ) , ir distance upto 100 ft ( 30 m ) , depending on scene reflectance, day / night auto ( icr ) / color / bw, backlight compensation blc / hlc / dwdr, white balance, auto / manual, gain control auto / manual, noise reduction 3d, privacy masking upto 4 areas, focal length 2.8mm, max. aperture f2.1, horizontal angle of view 92degree, lens type fixed, video compression h264 ( main / high / baseline profile ) / mjpeg, resolution 3mp ( 2304x1296 ) , 1080p ( 1920x1080 ) , 720p ( 1280x720 ) , d1 ( 704x576 / 704x480 ) 50 video recorder: simultaneous multi channel live view, real time recording, playback, network operation, remote access, usb backup, user interface support 16 bit true color graphical menu interface and mouse operation.preview screen 1 / 4 / 8 / 16 / 24 windows, ip video input 24 channels, video standard pal ( 625 line, 50t / s ) , ntsc ( 525 line, 60t / s ) , video compression h264 high profile, display moitor d1;vga & hdmi, hd ( support 1920x1080, 1280x720, 1440x900, 1260x1024, 1024x768, 800x600 ) 51 display: screen size 42 inch or above ( lg / sony / samsung / philips ) , panel technology ips, aspect ratio 16:9, native resolution 1920x1080 ( fhd ) , brightness 350nit or higher, contrast ratio 1100:1 or higher, dynamic cr 500, 000:1 or higher, viewing angle ( hxv ) 178x178, orientation portrait & landscape, operation temperature 0 degree c to 40 degree c, safety ul, eul, emc fcc class a, ip video unit 16 channel, 1 ch, rca ( 2.0 vp p, 1kohm ) two way audio input, 100 mbps incoming bandwidth, 80 mbps bandwidth, 128 remote connection, hdmi / vga output : 1 ch, resolution hard disk 4 tb camera installation and connectivity telephone 52 epabx with 50 line extension up to 80 line with 2 slt / 2 console the equipment shall be electronic type. it shall have microprocessor / micro controller based.it shall employ pcm / tdm / ip, 100% non blocking, ip digital switching technology.it shall have distributed processing architecture, slic and smt design.system power supply should be in built and smps type which input which input ranges from 90 – 265 vac, 48 60 hz & it has to be battery charger circuit inbuilt, so that, in case of power failure the psu can automatically switch to battery and vice versa. it should be suitable for dtmf as well as fsk type of telephone instruments.its capacity shall be suitable for maximum 96 numbers of c.o. lines, 120 analog extension lines and 500 ip extensions. 53 supply, installation, testing & commissioning of termination box for 50 pair epabx system complete as required 54 base phone cli ( panasonic / beetal ) landline phone with caller id facility corded phone numerical keypad 35 call logs3 display lines disclaimer, tone / pulse switchable ring led indication flash pause dynamic change over from pulse tone, 1 year manufacturer warranty 55 digital console phone 56 network switch : 24 x 10 / 100 / 1000base t, poe, fixed, 2 x sfp 100 / 1000 mbps, 52 gbps sitching performance capacity, 39 mbps forwarding performance rate, 525 k byte packet buffer, 8k mac address table, 9k byte jumbo frame, 170 watt poe power. 57 smart ups on line, 5.4 kw / 6 kva with 1 hour backup12 v 65 ah smf battery ups toplogy double conversion on line, power rating ( va / watts ) 5400watts / 6000va, form factor rack / tower convertible; output power capacity 5400 watts / 6000 va, max configurable power 5400watts / 6000va, nominal output voltage 230v, output voltage note configurable for 220 : 230 or 240 nominal output voltage, efficiency at full load 94.00%, output voltage distortion less than 3%, output frequency ( sync to mains ) 50 / 60 hz + / 3 hz, crest factor 03:01, waveform type sine wave, output connections ( 1 ) *hard wire 3 wire ( 8 ) * ( h n + g ) iec 320 c13 ( 8 ) , bypass built in bypass, output short circuit protection yes, parallel redundancy ( option ) 1 + 1, nominal input voltage 230v, input power factor>0.98, input frequency 40 70hz, input connections terminal block, protection thermal circuit breaker ( 250vac / 20a ) , input voltage range for main operations full load 160 285v, input voltage range for mains operation half load 160 285v, high voltage withstand capability 420 vac, green mode range 210 250 vac ( 230 v ) , battery type mintenance free sealed lead acid battery with suspended, electrolyte. 12v 65 ah smf battery for 60 min battery back up. 58 supplying and drawing following pair 0.5 sq. mm fr pvc insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed pvc conduit as required. networking 59 supplying & fixing rj 45 type computer socket suitable for cat 6 on modue gi box along with base and cover plate in surface or in recess including making connection , soldering etc as required. supplying and drawing utp 4 pair cat 6 lan cable patch cord 1 meter patch cord 2 meter 60 24 port gbe smart managed switch with gbe uplink interfaces 24 ports 10 / 100 / 1000mbps+4 sfp;port standards & functions ieee 802.3 10base t ethernet ( twisted pair copper ) , ieee 802.3u 100basetx fast ethernet ( twisted pair copper ) , ieee 802.3ab 1000base t gigabit ethernet ( twisted pair copper ) , ieee 802.3az compliance autonegotiation, ieee 802.3x flow control; full / half duplex full / half duplex for 10 / 100 mbps speeds, full duplex for gigabit speed;media interface exchange auto mdi / mdix adjustment for all twisted pair ports;switching capacity 56 gbps; transmission method store and forward; mac address table 16, 000 entries per device, maximum 64 bytes packet forwarding rate 41.7 mpps, packet buffer memory 1.5 mb, maximum power consumption 22.45 watts, standby power consumption 17.84 w / 240 v, acoustics 0 dba heat dissipation 76.55 btu / hr certifications ce ( lvd ) 61 category 6, utp 24 port patch panel size 482.6mm x 44.2 ( 19’’ x 1u ) , panel material steel fully powder coated, unshielded rj 45, plug insertion cycle 750 times dc resistance 72ω max, voltage rating 72 vdc max, current rating 1.5a max 62 supply fitting fixing rack 19 12u fully powder coated complete etc as required with complete accessories ( 5 amp x 6 socket, wire manager, rack fan ) valrack / netrack make. 63 wireless n access point interface one 10 / 100mbps rj45 port ( auto mdi / mdix ) , button wps button, reset button, external power supply 9vdc / 0.6a, antenna type 5dbi detachable omni directional antenna, frequency 2.4 2.4835ghz, wireless standards ieee 802.11n, ieee 802.11g, ieee 802.11b, wireless security ssid enable / disable mac address filter 64 / 128 / 152 bit wep encryption wpa / wpa2 / wpa psk / wpa2 psk ( aes / tkip ) encryption wireless modes ap mode, multi ssid mode, client mode, repeater mode ( wds / universal ) , bridge mode, tplink / cisco / netgear panel meter board mb 1 incomer 125a, 415v, ics=icu=25ka rupturing capacity, fp, mccb with extended rotary handle 1 no. 1 no. type 1+2 class i+ii lightning surge arrester 3 pole plus neautral. obo make type no. v25 b+c 3npe385 as per item no. 5094478 with mpcb busbar heat shrinked colour coded aluminium bus bars with smc / dmc busbar supports, nuts & bolts with spring washers. a set of tpn 200a al bus bars. current density shall be 1a / sq.mm instrumentation for incoming 1 no. three phase 0 500v digital voltmeter with selector switch 1 no. 0 125a digital ammeter with cts 125 / 5a and selecter witch 1 set of led type phase indicating lamps with hrc fuses meter compartments meter compartments with electonic meters three phase direct type 10 nos. the vendor shall submit details before fabrication outgoings 25 32a fp mcb 12 nos. supply of main l.t. panel fabricated out of 16swg m.s. iron sheets, compartmentalized type, with epoxy powder protective paint having sufficient housing compartpents for mounting of switchgears as per below mentioned specifications, make: kde / scpl / equivalent design, fabrication and supply of suitable electrical grade enclosure, compartmentalized type with epoxy powder protective paint and panel is to be fabricated out of 16swg make: kde / scpl / equivalent supply and installation of 1000 amp of electrolytic aluminium busbar for power load section. supply and installation of proper dmc busbar supporting system suitable for 1000 amp ratings. 250 amp, 35 ka, tpmccb supply of 160amp, 4pole mccb extended rotary handle make: abb / ge / siemens. 25 / 100 amps. 4 pole mccb, 16 ka cable 3.5 core, 300 sq. mm xlpe / pvc insulated sheathed ( heavy duty ) armoured electric cable with aluminium conductor. 3.5 core, 95 sq. mm xlpe / pvc 3.5 core, 150 sq. mm xlpe / pvc 3.5 core, 185 sq. mm xlpe / pvc detailed estimate for the proposed renovation and upgradation work for food test lab at first & 2nd floor, patliputra industrial area, patna. n.s. 1 parking deck flooring with high build, solvent free textured finish epoxy coating with roller applied 5 mm thick epoxy resin based floor coating nitoflor fc150 over epoxy resin screed nitoflor tf 5000 the intended surface shall be prepared by mile scarification to get mechanical key effect to the primer and the concrete surface for ensuring maximum bonding. strong degrease shall be used to remove the oil deposit on the concrete if any. dust and loose particles shall be cleaned using vacuum cleaners . after which nitoprime 25 shall be applied after mixing the base and hardener mechanically using a slow speed heavy duty drilling machine ( 400 to 500 rpm ) fitted with a suitable paddle to achieve homogeneous mix and applied on the prepared surface. after primer nitoflor tf 5000 shall be applied as a base layer after mixing the base hardener and aggregates throughly and poured on the primed surface and spread evenly to maintain the required thickness of 3 mm. the material should be tampered with a wooden float to ensure complete compaction and finally finished to closed even texture using a steel trowel and cured for seven days. as a finishing coat nitoflor fc 150 shall be applied over the screed surface after mixing mechanically the three components using heavy duty slow speed paddle mixer until achieving a homogeneous mix and spread on the prepared area using medium haired rol;ler for a thickness of 400 microns in two coat. 8.2 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement: 4 coarse sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels. 8.2.2 granite of any colour and shade 8.2.2.2 area of slab over 0.50 sqm 8.3 extra for providing edge moulding to 19 mm thick marble stone counters, vanities etc. over item no. 8.2 mm thick marble stone counters, vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. granite work 8.3.2 granite work 26.27 providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance ( rh ) of 99%, light reflectance ≥85%, thermal conductivity k=0.057 w / m k, fire performance as per ( bs 476 pt 6 & 7 ) in true horizontal level suspended on interlocking t grid of hot dipped all round galvanised iron section of 0.33mm thick ( galvanized @120gsm ) comprising of main t runners of 15x32mm of length 3000mm, cross t of size15x32mm of length 1200mm and secondary intermediate cross t of size 15x32mm of length600mm to form grid module of size 600x600mm suspended from ceiling using galvanized mild steel item ( galvanised @80gsm ) 50mm long 8mm outer diameter m 6 dash fasteners, 6mm diameter fully threaded hanger rod upto 1000mm length and l shape level adjuster of size 85x25x2mm, spaced at 1200mm centre to centre along main t. the system should rest on periphery walls / partitions with the help of gi perimeter wall angle of size 24x24x3000mm made of 0.40 mm thick sheet, to be fixed to the wall with the help of plastic rawl plug at 450mm centre to centre & 40mm long dry wall s.s. screws. the exposed bottom portion of all t sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. the work shall be carried out as per specifications, drawings and as per directions of the engineer in charge. 26.27.2 with 20mm thick beveled tegular mineral fibre false ceiling tile ( nrc0.7 ) . 12.45.3 providing and fixing false ceiling at all height including providing and fixing of frame work made up of special sections power pressed from m.s. sheet and galvanized in accordance with zinc coating of 120 gms / sqm as per is:277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm at 1200 mm centre to centre one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts to the angle hanger of 25x25x5 mm of required length, and other end of angle hanger being fixed with nut and bolts to g.i. channels 45x15x0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm centre to centre shall be fixed in a direction perpendicular to g.i. channel with connection clips made out of 2.64 mm dia x 230 mm long g.i. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450 mm centre to centre with 25 mm long drive all screws @230 mm interval including jointing and fixing to a flush finish of tapered and square edges of the gypsum board with recommended filler, paper tapes, finishers and two coats of primer suitable for gypsum board as per manufacturers specification and also including the coat of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per the drawing and specification and direction of the the engineer in charge but excluding the cost of painting. 12.5 mm thick tapered edge gypsum moisture resistant board 12.62 extra for any sunk or raised moulding in the plaster of paris ( gypsum anhydrous ) ceilng .all complete as per specification and direction of e / i. ns 2 supplying fitting and fixing roman blinds in jacard cloth finish as per company specification and as per approved colour and sample inclusive of all taxes and royalty all complete as per specifications / approval and direction of engineer in charge. n.s. 3 providing & fixing double skin laminated both side wpc partition upto specified height with 1.0 mm lamination of greenply / marino / century mica over 12 mm thick wpc of alstone / greenply / century ( min wt. 550kg / cum ) make fitted and fixed both sides over aluminium frame of 50 x 50mm posts at 60 cm centres and 50x50mm horizontal members at approx 60 cm centers including cost of anchoring the partition to floors, walls and ceiling properly as per drawing including making hidden doors as per drawing all complete as per drawing, specifications and direction of e / i. providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of engineer in charge ( door handle , lock, and stopper etc . n.s 4 supplying fitting and fixing glass door handles, h type ( qbghl 5 ) made up of stainless steel brushed steel finish 300 mm heigh / equivalent make all complete including taxes and royalty as per approval and direction of e / i. n.s 5 supplying fixing and fitting high security corner lock for patch fitting ( qbpl 1 make ) brushed steel finish made of graded aluminium alloy cast housing slim and compact size light in weight all complete as per specification and direction of e / i ns 6 providing and fixing of 1.0mm laminated ( greenlam / century / merino ) panelling upto specified height over 12 mm thick wpc board of alstone / greenply / century make fitted and fixed over aluminium frame of 25 x 25mm posts at 30 cm centres and 25 x 25mm horizontal members at approx 30 cm centers including cost of anchoring the panelling to walls properly including termite treatment as per drawing specification and direction of e / i. 14.1.1 repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground, all complete as per direction of e / i. cement mortar 1:4. 13.74 removing white or colour wash by scraping and sand papering and preparing the surface smooth including necessary repair scratches etc. complete 13.80 a.2 providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 13.92 wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. 13.92.1 two or more coat on new surface. 9.48 providing and fixing m.s grills of required pattern in frames of windows etc. with m.s flats, square or round bars etc. all comlete. 9.48.1 fixed to steel windows by welding. 13.94 painting with sythetic enamel paint of approved brand and manufacture to give an even shade. 13.94.1 two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. 15.23 dismantling tile works in floor and roofs laid in cement mortar including stacking material within 50 metres lead. 15.23.2 for thickness of tiles above 25 mm and upto 40 mm 15.7 demolishing brick work including stacking of serviceable material and disposal of unserviceable materials within 50 metres lead : 15.7.4 in cement mortar disposal of building rubbish / malba / similar unserviceable, dismantled or waste waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer in charge, beyond 50 m initial section 3: electrical work s.h. i : wiring 1.3.3 point wiring in pvc conduit, with modular type switch: wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit, with modular switch, modular plate, suitable g.i. box etc. as required. group c 1.4 twin control point wiring in pvc conduit with modular type switch: wiring for twin control light point with 1.5 sq mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit, 2 way modular switch, modular plate, suitable g.i. box etc. as required. 1.5 power plug wiring in pvc conduit ( 2x4 sq. mm ) : wiring for light / power plug with 2 x 4 sq. mm fr pvc insulated copper conductor single core cable in surface / recessed pvc conduit alongwith 1 no. 4 sq. mm fr pvc insulated copper conductor singlre core cable for loop earthing as required. ( for 15 amp socket ) 1.7 circuit / sub main wiring in pvc conduit : wiring for circuit / submain wiring alongwith earthwire with the following sizes of pvc insulated copper conductor, singlre core cable in surface / recessed pvc conduit as required. 1.7.1 2 x 1.5 sq.mm. + 1 x 1.5 sq. mm earth wire 1.7.2 2 x 2.5 sq.mm. + 1 x 2.5 sq. mm earth wire 40185 4 x 4 sq.mm. + 1 x 4 sq. mm earth wire 40550 4x 6 sq.mm. + 1 x 6 sq. mm earth wire 1.16 telephone wiring in existing conduit: supplying and drawing following pair, 0.5 sq. mm fr pvc insulated copper conductor, unarmoured telephone cables in existing surface / recessed pvc conduit as required 1.16.2 2 pair 1.21 s / f pvc conduit: supplying and fixing of following sizes of pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recess conduit as required. 1.21.1 20 mm 1.24 s / f modular type switch / socket : supplying and fixing following modular type switch / socket on the existing modular switch / socketon the existing modular plate& switch box including connections but excluding modular plate etc. as required. 1.24.4 3 pin, 5 / 6 amps socket outlet 1.24.5 6 pin, 15 / 16 amps socket outlet 1.24.6 telephone socket outlet 1.24.8 bell push 1.27.1 s / f modular boxes, base & cover plate: supplying and fixing following size / modules, gi box along with modular base & cover plate for modular switches in recess as required. 1 or 2 module ( 75 mm x 75 mm ) 1.31 s / f light plug point modular type accessories: supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch, connection, painting etc. as required. ( for light plugs to be used in non residential buildings. ) 1.32 s / f power plug point modular type accessories: supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5 / 6 & 15 / 16 amps modular socket outlet and 15 / 16 amps modular switch, connection, painting etc. as required. 5.4 supplying and fixing replaceable compact commercial batten suitable for single tb led tube complete with 20 watt led polycarbonate tb tube with built in driver etc. directly on wall / ceiling including connections with 1.5 sq. mm fr pvc insulated copper conductor etc. as required. 1.37 providing and fixing ding dong call bell suitable for single phase, 230 volts complete as required. 8.15 supply and installation of regular / standard model a.c. ceiling fan of 1200 mm sweep with service value ( cm / mm ) minimum 4.00, air delivery minimum 270 cum / min including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq mm fr pvc insulated copper conductor etc as required. 5.7 supplying and fixing recess mounted following types led downlighter with minimum efficacy 100 lm / w in pressure die cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm frls pvc insulated copper conductor cable etc as required. 5.7.1 5 / 7 watt 5.7.5 18 watt 5.9 supplying and fixing recess mounted 36 watt led flat panel ( 2 x 2 ) with minimum efficacy 100 lm / w which provides soft light and glare free symmetrical illumination suitable for armstrong / grid ceiling and integrated electronic driver etcdirectly on false ceiling including connections with 1.5 sq.mm frls pvc insulated copper conductor cable etc as required. 5.11 supplying and fixing wall mounted light bracket / fixture made with polycarbonate suitable for single 9 / 10 watt led lamp directly on wall including connections etc as required. ( but without lamp ) 6.1.6 supplying and fixing of following types lamp in the existing electrical fitting / fixtures etc. as required. 14 / 15 watt cfl lamp. 2.12 s / f c series, sp mcb: supplying and fixing following rating, 240 / 415 volts, c curve, miniature circuit breaker, suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 2.12.1 6 / 32 amps, single pole 2.12.2 6 / 32 amps, spn 2.12.4 6 / 32 amps, triple pole and neutral 2.12.8 40 amps, triple pole and neutral 2.19 supplying and fixing 20amp 240 volts spn mcb industrial type, power socket with 25amp spn mcb and 25 amps top in proper size steel box and plate as required. all complete as per instructions of elec.er. / architect. 8.11 supply and fixing of fabricated electrical control panel of cubical construction, floor / wall mounted type, fabricated out of 16 swg crca sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, bus bar chamber, insulator and complete in all respect etc and panel manufactures must be approved by cpri. ( but without ryb inicator, ammeter, voltmeter, inter connection copper conductor cable / solid copper strip, switchgears etc. ) ...

Planning And Development Department - Bihar

34921495 bids are invited for boq boq floor coating , bala paint , normal canvas paint , name board , minor electricity repair , whiteboard with duster total quantity : 308811...